Best way to get the leaf spring frame bushings out??

Z SKI

Donating Member
Like the title said. I tried banging on them and the truck was moving a little to much for me. Any tips on how to get them out??

Thanks,
 

Bustedsm

Numbered Car Crazy
Re: Best way to get the leaf spring frame bushings out??

Heat is usually the best resort to getting any sort of bushing out :D
 

Chest Rockwell

Active member
Re: Best way to get the leaf spring frame bushings out??

Ran into the same problem with my '92 C1500. A little too close to the bed for my comfort with a torch, but I was able to get in with a big c-clamp and force the bushing out that way. Rust sucks.
 

4C FED

Absolutum Dominium
Re: Best way to get the leaf spring frame bushings out??

Get a propane torch kit. Apply the flame to the center of the steel bolt eyelet for about a minute.
Push eyelet out with a screwdriver.
Pry the rubber out with a screwdriver.
 

warmpancakes

New member
Re: Best way to get the leaf spring frame bushings out??

or just light the bushing on fire, it will melt out, then collapse the sheel and remove
 

Daveman2

Autox Blazer
Re: Best way to get the leaf spring frame bushings out??

What I've done is when the leaf is OUT of the vehicle, place the leaf on it's side and basically use a long rod like a torsion bar if you have a spare one around, and ram it out. BFH will probably work too.

I'm in the california though don't have as many rust/corrosion problem as you other rough weather guys.
 

SY2455

70's Veteran
Re: Best way to get the leaf spring frame bushings out??

Paul I just did mine in early Dec. I use the following to do it.

1. A small propane torch.

2. 1 = 1/2" X 71/2" grade 8 bolt with alot of thread and nut.

3. A couple of spacers smaller than the rubber in the bushing with a 1/2" hole for the bolt.

4. A 2" copper pipe couping.

5. 1 = spacer larger than the copper coupling with a 1/2" hole for the bolt.

6. A 1/2" drive inpact and wrench to fit.

I used the torch from the inside of the frame so I would not heat the gas tank, I put the end of the torch inside the bushing sleeve to heat the bushing. Once the bushing started smoking on the other side, I turn off the torch and install the bolt with the spacers smaller than the rubber in the bushing. On the inside of the frame I install the 2" copper pipe couping and the spacer larger than the copper coupling with a 1/2" hole for the bolt so the couping will receive the rubber and sleeve that the bolt will pull out. I then spit the outer sleeve with a air inpact hammer and remove it. Once I got started it took about 3.5 hours to do all 6 bushings :tup:. I hope this helps.
 

4C FED

Absolutum Dominium
Re: Best way to get the leaf spring frame bushings out??

or just light the bushing on fire, it will melt out, then collapse the sheel and remove
Shells in the frame stay in. In the leaf they come out.
Lighting the bushing on fire is messy.
 

4C FED

Absolutum Dominium
Re: Best way to get the leaf spring frame bushings out??

Seriously, once you get the metal bolt eyelet hot enough it will push out with a screwdriver. Then the bushing is cake.
I did my control arms this way this weekend.
 

jbtsurf

New member
Re: Best way to get the leaf spring frame bushings out??

use a small drill bit and drill out as much as you can by wollowing out the rubber in between the leaf eye and the sleeve. drill half way throught the eye from each side. ive found this to be a better method over a stinky fire ball of rubber goop. however it does require a little more finess.
 

blk00z28

Forced to by choice
Re: Best way to get the leaf spring frame bushings out??

I don't mean to take his thread from him. But what are you guys doing about the leaf spring bolts? What are you replacing them with? All, yes ALL of mine I had to beat out and damaged them to the point where I need 6 new bolts. Anyone have replacements, or what what grade and where to get them from?
 

SY2455

70's Veteran
Re: Best way to get the leaf spring frame bushings out??

Just go to the stealership and get 6 ea of part #

1. Bolts = 11513937

2. Nuts = 11500748

3. Washers = you need 12 of these 2441143

These are the stock part # for our trucks. The part # show good for the bolts and the washers, but has change for the nut. My contact isn't at work yet so I can't get the new # for the nuts. The bolts and nuts are rated as a grade 10.9 so I don't know if a grade 8 bolt and nut will work.
 

warmpancakes

New member
Re: Best way to get the leaf spring frame bushings out??

grade 8 and 10.9 are the same basically ones a english measurement the other metric
 

SY2455

70's Veteran
Re: Best way to get the leaf spring frame bushings out??

Thank You Ken, I learned something new today.
 

Z SKI

Donating Member
Re: Best way to get the leaf spring frame bushings out??

Thanks all. I give it another try this weekend.
See ya,
 
Top