no tach signal with msd FIXED!!

TYTILIDIE

METH HEAD
I have a 6AL box and using the jumper harness and I have no tach, when I go back to stock I have it? Any ideas?
 
Last edited:

NecroWolf

lost marbles member
Re: no tach signal with msd

Re: no tach signal with msd

isn't the tach signal with the msd box from the box itself?
 

TYTILIDIE

METH HEAD
Re: no tach signal with msd

Re: no tach signal with msd

Hell if I know. Just thought it was weird and not sure how to fix it.
 

NecroWolf

lost marbles member
Re: no tach signal with msd

Re: no tach signal with msd

i think on my msd i have a male spade connector that is the tach output.
 

SY2455

70's Veteran
Re: no tach signal with msd

Re: no tach signal with msd

Did you connect it right ? On mine it was just a plug and play affair. When I get home from work I will look for my paper work if it will help you.
 

TYTILIDIE

METH HEAD
Re: no tach signal with msd

Re: no tach signal with msd

Switched back to the stock alternator. Tach flutters like a mo fo. I will try out hte noise reducer. Anyone know a lot about the big early 90's alternator wiring? I was only getting 12 volts out of it but it checked out great at the auto store. Stock one works fine too but wnated to use that big 140 amp of a caddy. I think maybe I needed to use a different harness on it. any suggestions?
 

ghettosled

SYTY SUPERSTORE
Re: no tach signal with msd

Re: no tach signal with msd

with the jumper harness it should be plug-n-play. just like stock. the white wire on the two wire plug to the back of the distributor is the ground/tach. i had to install a msd noise filter on a recent truck with a msd 6a b/c it made the datamaster crap out..
 

TYTILIDIE

METH HEAD
Re: no tach signal with msd

Re: no tach signal with msd

Well something is definitely off, I installed the noise filter as you guys told me to and now the tach doesn't move at all. One thing I have noticed is that when I go back to stock coil, tach works but truck runs like it has a big lope. Damn I hope I didn't wire anything wrong in the harness.
 

Aeroking

e.i.
Re: no tach signal with msd

Re: no tach signal with msd

make sure your 12V source is coming directly from the battery, or a remote battery terminal, and NOT the alternator post. and make sure the box has a solid ground to the frame.

:2cents: my 6AL has a spade connector on the box for an auxiliary tach as well, but i dont use it.
 

cloneman315

Active member
Re: no tach signal with msd

Re: no tach signal with msd

make sure none of the msd power wires are ran along the main firewall engine harness.And go to the battery with both cables.
 

cloneman315

Active member
Re: no tach signal with msd

Re: no tach signal with msd

the factory tach should have nothing to do with the msd.truck will run alot better with the msd on it!
 

TYTILIDIE

METH HEAD
Re: no tach signal with msd

Re: no tach signal with msd

Not positive, I have to do a little more research but, I think I have found my problem. The white wire at the MSD harness I used to hook up my voltmeter. I put the red wire on it. I did an ohm check and got a reading at the white wire on the two wire plug at the distributor. Well, for shits and giggles, I tested the white wire on the four wire plug at the distributor and got a reading. These wires are clearly connected. I am going to test these wires on a friends stock truck today and make sure I shouldn't have signal to both. If this ends up being the case, I know exactly where the problem should be and this wont be a hard fix.
 

Aeroking

e.i.
Re: no tach signal with msd

Re: no tach signal with msd

yours isnt a plug-n-play deal??? mine took a 12V, a ground, and the harness connection.
 

Don W.

Stab it and steer it
Re: no tach signal with msd

Re: no tach signal with msd

Hi Mike,

Not much help but FWIW I have a 6al as well. No prob, and not even the noise reducer. P&P using the MSD harness.

Does the alt have an internal regulator?
 

TYTILIDIE

METH HEAD
Re: no tach signal with msd

Re: no tach signal with msd

Running the stock alternator. Yes, I have the plug and play set up. I disconnected the harness a minute ago and checked for signal on the 4wire plug to the dist, no signal. Its only there when the harness is plugged in, but I guess the tach is the same as ground right? So that would explain that. Im not sure what to think here.
 

1madgumby

New member
Re: no tach signal with msd

Re: no tach signal with msd

I have A noise reducer that I told you about & the factory tach still does not work half the time.( all the other guages work just fine) I have A 5" autometer tach that I never have A problum, I give up on the stock tach Awhile ago, it is like 200 rpms off anyhow.


Well something is definitely off, I installed the noise filter as you guys told me to and now the tach doesn't move at all. One thing I have noticed is that when I go back to stock coil, tach works but truck runs like it has a big lope. Damn I hope I didn't wire anything wrong in the harness.
 

TYTILIDIE

METH HEAD
Re: no tach signal with msd

Re: no tach signal with msd

Interesting, the more I go through the harness and test things the more I am realizing I didn't screw anything up. I think I am going to give MSD a call and see if they have any thoughts. BTW, Did you guys with 6al boxes cut the red loop? Thats what the directions say for 6cyl aps but I have tried it both ways with no results.
 

TYTILIDIE

METH HEAD
Re: no tach signal with msd

Re: no tach signal with msd

I called MSD today, they suggest a tach adapter. Im thinking I shoudnt need it since no one else does but, should I try it anyway?
 
Top