Comp Cams 1.6 full rollers

Nitrous

New member
Re: Comp Cams 1.6 full rollers

Are you getting coil bind with the 1.6's? I know on my old vortec heads I ran 1.6' with an increased cam and broke the valve spring but I knew it was going to with .528" lift on a stock vortec head. This is why I love LS1 heads, you can run .600" plus lift with a good set of springs and you're ready to go. Just stay away from Manley, I broke too many sets including the LS1 springs. Patriot dual gold is tthe way to go. Sorry to get off topic here but depending on your cam lift 1.6 rollers will give you some decent HP numbers.
 

Nitrous

New member
Re: Comp Cams 1.6 full rollers

They look nice, did you have to bore out the push rod holes any to keep the mfrom rubbing?
 

Injected1

Member
Re: Comp Cams 1.6 full rollers

Why are you selling them?

I failed to realize that in order to run 1.6 rr pushrod holes need to be elongated so they don't rub. My options are:
1. sell these new rockers and take a loss to by 1.5's
2. take the heads off the motor and drill them out (cost at least $300)
3. Try to drill them on the block with magnets and hope no shavings go in (too risky)
4 run it like it is and risk braking something in my $35k build

That's why I am selling them.
 

Syclone#2960

What ever it takes!!
Re: Comp Cams 1.6 full rollers

I failed to realize that in order to run 1.6 rr pushrod holes need to be elongated so they don't rub. My options are:
1. sell these new rockers and take a loss to by 1.5's
2. take the heads off the motor and drill them out (cost at least $300)
3. Try to drill them on the block with magnets and hope no shavings go in (too risky)
4 run it like it is and risk braking something in my $35k build

That's why I am selling them.

I run guide plates.. they rub to keep them straight. Resolved my knock issue when reving in park.
 

Syclone#2960

What ever it takes!!
Re: Comp Cams 1.6 full rollers

Run guideplates with self-aligning rockers?

I dont recommend running self-align rockers at all. It took me 3 years to figure out a knock issue in my sy because of these. You can only run one or the other. The full rollers without self aligners are less noisy.

These are ideal for someone running an aftermarket engine management system. Where they can turn off the knock sensor and run off the WB02 readings.
 
Last edited:

Nitrous

New member
Re: Comp Cams 1.6 full rollers

I drilled out my vortec 350 holes in place and vacuumed out the shavings while drilling and I've also pulled the heads so it'll work either way just cover things up and have a shop vac and magnet. If you keep a lint free rag covering everything you'll be fine. I did alot of testing with different cams and vortec heads on my 97 GMC before installing the 2002 LS6. Holley-NOS and I played with the plastic intakes and I was able to push a 175 shot all day long using an LS1 NOS kit and made 429 rwhp. You can't beat an LSX engine though HP+Gas mileage=:tup: If you decide to go with the 1.6's just make sure you keep the lift stock on the cam or you'll break the springs. The longest I ever made was 72,000 miles on the L31 and on my LS6 with Manley's made it 1200 miles and then I put new heads and dual patriot golds and love it but I had reduce the knock sensor sensitvity due to false knock retard. These are still good rockers you have and someone looking for some cheap horsepower should jump on them. I was able to get 25 rwhp with the 1.6's on the L31. :tup:
 
Top