How did you route your IC lines??

Syclone Rob

Its all ABOOT the SYTY eh
I replaced my metal IC lines with 3/4 inch heater hose... I hate the way its routed. My original plan was to run it in the passenger side fender well but the problem I ran into was that the heater hose would kink right behind the upper IC due to being to sharp of a turn to go by the blower box.

heaterhose.jpg


Can whom ever did this post some pics on which way you ran it? I truthfully don't like it the way I have it.

Rob
 

Syclone Rob

Its all ABOOT the SYTY eh
Re: How did you route your IC lines??

Divergent Lightning said:
I used a few of the plastic 90 degree elbows to solve the kink problem. Peice of cake

I would assume I can get these elbows at a local autoparts place or will the plastic elbows from the plumbing department do?
 

lurk

New member
Re: How did you route your IC lines??

I got mine at menards. you will have better luck finding the 90's there or lowes or somewhere that sells plumbing stuff
 

SeattleSy#1255

Category 5 Conservative
Re: How did you route your IC lines??

i rerouted them down the pass. side fender well so you can't even see them.
 

syclonekid43

New member
Re: How did you route your IC lines??

i used 2 hoses that had a nice bend to them. then just joined them with a straight plastic connector.ran the inside the pass side fender
 

TYRODD

My ass. Look at it.
Re: How did you route your IC lines??

Syclone Rob said:
I replaced my metal IC lines with 3/4 inch heater hose... I hate the way its routed. My original plan was to run it in the passenger side fender well but the problem I ran into was that the heater hose would kink right behind the upper IC due to being to sharp of a turn to go by the blower box.

You need two 180* 3/4" Heater Hose bends to make it around the upper IC, I got mine at NAPA for like $12 apiece. They look pretty clean! :tup:
 

sytyguy

Moderated User
Re: How did you route your IC lines??

Paul.....I'll be happy to look anything remotely like your truck anyday.:tup:

Hood
 

skwayb

NWSTP
Re: How did you route your IC lines??

Thanks.. Yours actually looks cleaner with the radiator resovoir and ABS removed. I swore for a second I was looking at mine... :)

Mine looks a little bit different now. I have Razor's Alky kit on there and installed it as stealth as I could. I had bearing go out in my AC Delete pulley and caused all my billet pulleys to get eaten up. So now I have the standard tension and AC Delete pulley on there....

I will have billet on there again.....well if Jeff Scott (J&S) would ever get my AC Delete Pulley remachined for a new bearing that I sent him 3 years ago.. LOL... We can dream :). Think Todd will be waiting a long time for his engine mounts especially since there is a steak on the line.
 

dgoodhue

BuSTeD 4.3
Re: How did you route your IC lines??

I have mine routed very similar to the first picture. The only difference is my feed line goes into and through the driver fender by the ABS. I routed mine like this because it gives me plenty of room to move my upper IC around the engine compart (read move it out of my way). However since adding alky I cant really move my IC around that much any more, so I will probably reroute ot the passenger side.
 

skata

Donating Member
Re: How did you route your IC lines??

here's another way. get some preformed bends and run the hoses along the side of the intercooler and then down along the side of the radiator area. you can put some pipe foam on the hose to if you want to help keep some heat out. also this is the shortest way to run them and the pump gets gravity fed.

also the self stick ductwork insulation works good on the intercooler.

feb280015sk.jpg




feb280039qx.jpg
 

TYRODD

My ass. Look at it.
Re: How did you route your IC lines??

Those 180* preformed bends are exactly what are needed. :)

However, running your IC lines right on top of the turbo/downpipe kind of defeat the purpose of deleting the stock metal lines...you want to keep the lines as far away from the engine/DP as far as you can, so that the coolant inside doesnt absorb any heat. Not too mention that looks like the heater hose would kind of be in the way right there, another reason to move them through the fender :) .

BTW, the shurflo pump is self priming up to 8 vertical feet, no need to gravity feed! :)

:2cents:
 

skata

Donating Member
Re: How did you route your IC lines??

TYRODD said:
Those 180* preformed bends are exactly what are needed.
icon_smile.gif


However, running your IC lines right on top of the turbo/downpipe kind of defeat the purpose of deleting the stock metal lines...you want to keep the lines as far away from the engine/DP as far as you can, so that the coolant inside doesnt absorb any heat. Not too mention that looks like the heater hose would kind of be in the way right there, another reason to move them through the fender
icon_smile.gif
.

BTW, the shurflo pump is self priming up to 8 vertical feet, no need to gravity feed!
icon_smile.gif


2cents.gif
my downpipe and turbo are wrapped, so heat soak is not much of an issue. by running the hoses through the fender, the coolant spends more than twice the amount of time in the hose(in the hot engine compartment) before it reaches the intercooler. that just gives the coolant more time to absorb heat. i figured the shortest route would work best, imo.
plus i like not seeing heater hose all over the place.
icon_smile.gif

oh well, i'm just giving you another option.
 

White97SVT

Member
Re: How did you route your IC lines??

Mine are hidden in the fender so you don't ever have to look at them. I will try and remember to get a pic tomorrow when i wash the truck.
 

White97SVT

Member
Re: How did you route your IC lines??

founda couple of pics. maybe you can see how it goes.
Pdr_0036.jpg

If you look to the left of the battery you can see it in there.
Pdr_0037.jpg
 

gmcturbo

Active member
Re: How did you route your IC lines??

i got mine routed like yours but above everything. its nice to be able to take the intercooler off and just set it on the abs unit and its all out the way..
 

TYTILIDIE

METH HEAD
Re: How did you route your IC lines??

100_1869.JPG

100_1880.JPG

100_1870.JPG


Heres how I did mine. When I did them at first the A/C box was there and thats why they were done this way. I used 2 90* 3/4m elbows and 2 90* 3/4"f elbows. I used a gasket seater called "The Right Stuff" (autozone), on the threads and screwed them together and made them the direction I wanted. I had these extra on my irrigation truck, Im pretty sure you can get them at Home Depot or what have you. I made my hoses clear as you can see so that I can tell if the pump is working. It also happens to just look cool I think.

Mike
 

GM TURBO

Sell Out
Re: How did you route your IC lines??

I'll get a pic of mine.

Basic idea...come off stock CCHE (aka lower IC). The upper inlet (non-pump side) required a 90* bend to keep from kinking. Go into drivers side fender at the lowest point possible. Go up through the fender and out behind the windshield washer tank. 90* bends there and into the upper IC.

I had to remove the the washer tank and it was a HUGE pita to get the hoses together. I should have left more length than I did.

My thinking was keeping it away from the turbo/dp as that is where most of the heat is generated (in my head anyway). Use as much hose as possible to increase the capacity of the system - the more fluid - the longer it will take to heat up (also longer to cool I suppose).

I also have my IC and DP wrapped.
 
Top