Blown headgasket?? - coolant filling up overflow

BoostedSUV

Active member
I am having problems with my truck pumping coolant from the Radiator to the overflow. Truck is running warmer than normal but not getting terribly hot. It's running at about the 1/4 way up mark on the temp gauge (that gauge sucks by the way). I changed thermostat and put a new 15lb radiator cap on with no effect on the problem. It's not loosing any coolant, just filling up the overflow. Everytime I drive the truck I have to pump the coolant back into the system beacause the overflow is near full, and rad is low. Its almost as if the truck is sucking in air and building pressure which pushes out the coolant. When I shut the truck off when I am done driving i can hear the pressure being released into the overflow. Oil is clean, nothing coming out the exhaust which is typical of a headgasket though. Electric fan is working properly etc... The water pump is new, only has about 2k miles on it, upper rad house is new, thermostat is new, and new Moroso 15lb radiator cap. I have been fighting this problem for about a month now and haven't found a solution! This truck is the biggest headache and money pit I ever had! It's real close to having and "accidental" fire so I don't have to deal with it. Any help would be great! Thanks!
 
Last edited:

gkrcr882

SyTyless......for now!
Re: Blown headgasket??

Re: Blown headgasket??

Did you try burping the system to get rid of all the air?
 

BoostedSUV

Active member
Re: Blown headgasket??

Re: Blown headgasket??

How would I go about doing that? I have refilled it a few times and it seems to be air free, but it seems as though it keeps getting more air in it as I drive and it gets hot and builds pressure.
 

gkrcr882

SyTyless......for now!
Re: Blown headgasket??

Re: Blown headgasket??

With the truck off and cold, remove the radiator cap. Start the truck and allow it to get up to temperature so the thermostat opens. Let it run for a few minutes so that any air in the engine coolant passages has time to migrate to the radiator. The air bubbles will escape through the open radiator filler. There might be other ways to do it, but this is the way I do it:2cents:
 

Try Me

New member
Re: Blown headgasket??

Re: Blown headgasket??

the radiator cap has to be the highest point in the system. you should be able to jack the front end up, start the truck with the cap off, and you should be able to tell when the thermostat opens up and coolant starts flowing. that will bleed off any air. if your truck isnt returning the coolant from the overflow than your system isnt tight (leak somewhere) and its able to draw air in rather than drawing the coolant back from the overflow.
 

BoostedSUV

Active member
Re: Blown headgasket??

Re: Blown headgasket??

I will try to bleed it the ways mentioned above. I have noticed when i run it with the cap off it creates little bubbles near where the cap would be. I don't see any leaks and everything is tight. That's why I thought it was getting air in from a headgasket possibly.
 

BoostedSUV

Active member
Re: Blown headgasket??

Re: Blown headgasket??

I just let the truck run for about a half hour with the radiator cap off. It was making a lot of bubbles and foam up near the cap which is the air excaping but it never really stopped. The temp gauge was reading normal and the elec fan kicked on, I assumed the thermostat opened up but there wasn't a real good water flow at any point. I am positive it got warm enough to reach the 180deg. thermostat point. I put the cap on and let it continue to run and it didn't backfill the overflow at idle but if I reved up the motor and decelerated it would backfeed right into the overflow and stay there. I checked all hoses for leaks and all clamps were tight etc. There wasn't any liquid coming out the exhaust, and the oil looks perfect. any other ideas?
 

Try Me

New member
Re: Blown headgasket?? - coolant filling up overflow

does the coolant look like it has oil in it? does it get a ton of smoke coming out of the cap when running? does the coolant smell like gasoline?
 

BoostedSUV

Active member
Re: Blown headgasket?? - coolant filling up overflow

Deff no oil in the coolant, i don't really smell gasoline or see it smoke when cap is off. it will steam when hot that's about it.
 

jwaller

Evil Genius/SyTy Guru
Re: Blown headgasket?? - coolant filling up overflow

borrow a pressure tester from a local parts store and pressurize the rad to 16psi. let it sit and see if it bleeds off. if it does your in trouble. if it holds your good.
 

QUICK STORM

B.A.M.F. BMW Tech
Re: Blown headgasket?? - coolant filling up overflow

my s-10 is doing the same, but i think it has a cracked head or blown headgasket. what mine does is the temp goes to about 225-230 for 20 secs then immeadiately drops to 180 and stays there for the rest of my driving. i don't worry aout it cause i only drive like 3 miles to and from work. and when i shut it off i can hear the coolant bubbling into the overflow. and there is always pressure in the system unless it sits overnight or for more than 4-6hours.
 

BoostedSUV

Active member
Re: Blown headgasket?? - coolant filling up overflow

Thats exactly what mine does too! except I have an hour drive each way to work. The radiator could be cold and it still has pressure built up, and it bubbles into the overflow when I shut it off. The motor was just rebuilt less then 3000 miles ago and I am only running 17psi at most! I find it hard to believe it has a bad head gasket. Who knows, the engine is new and I have already taken it out 3 times for other problems....
 

James Thomas

"NO CLASS"
Re: Blown headgasket?? - coolant filling up overflow

BoostedSUV said:
Thats exactly what mine does too! except I have an hour drive each way to work. The radiator could be cold and it still has pressure built up, and it bubbles into the overflow when I shut it off. The motor was just rebuilt less then 3000 miles ago and I am only running 17psi at most! I find it hard to believe it has a bad head gasket. Who knows, the engine is new and I have already taken it out 3 times for other problems....



Borrow or buy from the local parts store a "Cal-Van Block Check Kit". Follow the instructions and if the blue leak check fluid bubles and changes colors from blue to green or yellow, you have a blown gskt or worse. We use to have these problems on 5.0 Stang's ALL THE TIME. Not really overheating, at least until it pushed all the coolant out of the radiator anyway, but pushing the coolant out and keeping the system pressurized all the time, even right after start up. Coolant gets pushed to overflow then forced from overflow onto the ground. Engine cools and pulls what's left in the overflow back in but due to the extra amount of coolant above and beyond normal expansion that was lost, now its low on coolant..... all the time.

Now mind you the Ford only has 4 head bolts where our GM's have 5 and we can take a lean / detonation situation better then them and longer than the Fords but it "don't take a lot" to blow a gasket. Even more true if the detonation is just at the threshold point and is not real easy to detect. Over a period of time it will start to eat a weak spot in the gasket and one day it just starts pressurizing the cooling system (if your lucky and don't have your foot in it).On the 5.0's, guys were installing Paxtons and Vortech's with stock fuel systems and had little or no trouble with the 6-8 psi. "as packaged booost" but 80 percent would start loosing gaskets at 9-10 psi. Think about it, stock our trucks make more than that and most of use are way beyond our stock boost 18-20+ psi.
_____________
James Thomas
 

BoostedSUV

Active member
Re: Blown headgasket?? - coolant filling up overflow

well i pressure tested the coolant system and it held 16psi with out moving for about a half hour. I also tested the new cap I got and some times it would hold 16 and sometimes it would bleed all the way back to like 10ish... Is it possible its just the cap causing this?
 

ed hess

race or get outta the way
Re: Blown headgasket?? - coolant filling up overflow

Its a crack in the block or head most likely.

The motor i ran in 2004 was like this the whole year.

larger valves weakens the material and add some boost and it can happen.
made up a new head but still continued with the same symptoms your describing.

we just kept running it anyway since water never got into a cylinder or the oil.

eventually water did get into it.

tear down showed we where splitting the block in 2 on both banks about 2 inches down from the deck.

put a leakdown tester on the cylinders and watch the water level in the radiator rise.

compression check wont tell you squat on this.

fwiw i lost track of how many times i swapped head gaskets, remilled the head.

and we had orings in the block and grovves in the heads.
 

James Thomas

"NO CLASS"
Re: Blown headgasket?? - coolant filling up overflow

The block check kit detects the presence of combustion gas. If it's a small leak or just starting. Cooling system test my not show it unless the engine is hot or running if it shows it at all. I am sorry to neg. but I have seen this a lot and at times it can be hard to track down. Get the kit and check it.
_____________
James Thomas
 

Try Me

New member
Re: Blown headgasket?? - coolant filling up overflow

Ive had the same problem ed was talking about with my cylinder head. i got a nice crack right near one of the intake valves. between heavy porting, and 2.055 intake valves the metal gets a little thin and doesnt take lightly to any overheating or such...
 

BoostedSUV

Active member
Re: Blown headgasket?? - coolant filling up overflow

I was afraid that's what you guys would say. I am running stock size valves with very little port work on the heads, the block is only .030 over and I am running 17-18psi of boost.I find it real hard to believe that the headgasket went or that a head is cracked but that is what it sounds like to me as well. I have been around motors for a long time and thats what the symptons pointed to in mind as well. I will leak down test the motor this week and see what I find. I would rather drive my truck into a river then take the motor out for the fourth time this year. I hate this truck with a passion and no matter what I do prevent any sort of problem one develops anyway. This truck has been nothing but a headache for the 2 years I've had it and it has never been problem free to this day. If you see a '92 Typhoon floating down a river you'll know who's it is! haha
 

ed hess

race or get outta the way
Re: Blown headgasket?? - coolant filling up overflow

if you know anyone with a boroscope you can look for rust or evidence of water in the cylinder or the head / gasket area.

an inexpensive boroscope runs about 200 as i recal for mine.

ed
 
Top