Gauge..... repair or replacement?

James Thomas

"NO CLASS"
Did a search and didn't find much so I'll have to ask. I just bought a Ty and the factory cluster oil pressure gauge doesn't work and yes I am sure it's the gauge and not the sender or wiring. I don't want to install an seperate after market gauge so that is out :tdown:.

1. Does anyone know if the gauge can be replace seperatly with out swapping the whole cluster? If not, does anyone know who can repair a stock gauge / cluster.

2. Does any one have a good cluster for sale?

Thanks
James Thomas
 

canadian

sy in progress
Re: Gauge..... repair or replacement?

what are the symptoms? you double-checked that the gauge hasn't flipped all the way around and is resting under the stop? that's a common problem.
 

James Thomas

"NO CLASS"
Re: Gauge..... repair or replacement?

Yes the gauge is shorted... I think. I subbed in a different gauge and it woks, I also verified the circut with a meter and the wiring / sender is ok. This thing is cherry, stock and I'm not sure yet but still trying to verify the #'s and codes but I think a rare "Special order & optioned Ty from GM/P.A.S.) and I don't want to screw it up. HELP!
 

James Thomas

"NO CLASS"
Re: Gauge..... repair or replacement?

Out standing :tup: ! Thanks for the link and I'll call 'em in the morning!

_____________________________
James Thomas
 

James Thomas

"NO CLASS"
Re: Gauge..... repair or replacement?

They said they could fix it with no problem but....... They want $220 to do it! I just bought a whole cluster for about that.

___________
James
 

Peter

my Ty and me 25+ years
Re: Gauge..... repair or replacement?

As Canadian said, the most common problem with the oil pressure gage is the needle going all the way around and lodging on the wrong side of the stop pin. From there it will stay forever.

You can easily remove the gage cluster and flip the oil pressure needle back around. It will work for awhile but it will probably flip around again. Don't know exactly what causes it, but assume it is a voltage spike or noise.

Anyway, the permanent fix is to trim off the stop pin with a razor blade. Problem will be solved forever. Mine has been that way for 10 years, no more problems.

Peter
 

tnsyty

Active member
Re: Gauge..... repair or replacement?

Peter said:
Anyway, the permanent fix is to trim off the stop pin with a razor blade. Problem will be solved forever. Mine has been that way for 10 years, no more problems.

Peter

That works? Sweet. I have always wanted to install a stop pin on the upper side, but this is much easier. So it will flip around, and keep reading. cool!
 

bmwtech

New member
Re: Gauge..... repair or replacement?

So My Presure Guage Is Stuck On 60 And Never Moves . Is That Where They Stick When The Hit The Stop?
 

Quickstop [UK]

Combating adversyty.
Re: Gauge..... repair or replacement?

I am concerned about my coolant temp gauge.

I took the whole Instrument cluster out of the vehicle and manually adjusted the coolant gauge and it moved free and easy.

When I applied power, it immediately moved south and stayed there. It only registers above 40C so I am just wondering if the engine has not gotten hot enough.

I have a replacement sensor, but when I tested the sensor (short the cable to ground and see if the gauge goes hot) ther did not appear to be any movement. So something is driving the sensor but not in the manner that I am expecting.

How much for a new cluster then? And mine is the metric one - same as S10s apparently.

Anyone got any thoughts?

Thanks,

mark
 

nello

Active member
Re: Gauge..... repair or replacement?

Peter said:
As Canadian said, the most common problem with the oil pressure gage is the needle going all the way around and lodging on the wrong side of the stop pin. From there it will stay forever.

You can easily remove the gage cluster and flip the oil pressure needle back around. It will work for awhile but it will probably flip around again. Don't know exactly what causes it, but assume it is a voltage spike or noise.

Anyway, the permanent fix is to trim off the stop pin with a razor blade. Problem will be solved forever. Mine has been that way for 10 years, no more problems.

Peter

How did you get into the cluster to trim the pin with a razor? I'd like to try this but don't want to screw anything up. Thanks.
 

AWD

New member
Re: Gauge..... repair or replacement?

the cluster is quite hard to take apart...theres some screws in weird places and id recommend getting the diagram that shows all the screw points...it took me about and hour and a half to get it
 
Top