ViciousV6 visits Englishtown Raceway for Test & Tune

ViciousV6

400HP/550FTLB
Well guy as expected i unloaded 2 back to back mid 11's passes, would of been 3 passes but screwed up the 1st one on the rev limiter.

1st. Pass 12.10 @ 115 mph completely out of throttle and back in it.

2nd pass 11.63 @ 118 mph on vaccuum leak and no fuel pres regulator

3rd pass 11.69 @ 119 mph on same issue as 2nd pass.

Of course my vac line for fuel pre regulator decides it wants to pop off on both runs.
Both runs were made in Drive with no lock-up, 17 lbs of boost, no boost lauches leaving off idle, and spinning some tires all 60 foot times 1.8's

oh yea the first pass was done after driving 45 minutes to track, sat in tech inspection for an hour running, then got to stagin lanes and they took my lane right to the track.

Some videos coming right here!
My girlfriend took the video and has never shot videos before so disregard any comments!
http://www.youtube.com/watch?v=T5vOAzoie2M
http://www.youtube.com/watch?v=OqXZCq-B4IU

Hope You Enjoy,
I Did
Ralph
ViciousV6
 

mrweelr

New member
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

Not the best video, but better than nothing and congrats on the fast times :tup: Sounds like there's a lot more in the truck considering the low boost and 60' times. What's your build and what stall converter are you running?
 

autoaddictions

Active member
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

Thanks for the videos.! 119mph on 17psi with that little turbo ant bad at all!!! You got to boost that bitch up off the line. 1.70 60s be nice to see.
 

ViciousV6

400HP/550FTLB
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

MikeRenz said:
why don't you launch?

Well the problem is the tranny still has to be adjusting for the shift it is shifting @ 4800 so 3rd gear is real early, the 1st pass i tried manual shifting but hit the rev limiter because i get antsy and don't think about shifting. Right now the only way to hard launch is to manual it until i pull the governor out and adjust the weights on it. he truck has pulled 1.73 60 foots before on a little better lauches i was spinning in the 60 foot too. truck was not going staight so i got RPM Coilover set-up going in next week and still waiting on new downpipe and wastegate. Only thing that was changed on the the truck since my 12.00 passes here was new intercooler and headers from MPE with out any tuning adjusted. The truck is running 9.8-10.2 AFR on Pump gas right now.

Converter is TCS 2800 stall

Thanks Ralph
ViciousV6

Working on a track Rental for Atco so i can unleash it.
 

ViciousV6

400HP/550FTLB
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

mrweelr said:
Not the best video, but better than nothing and congrats on the fast times :tup: Sounds like there's a lot more in the truck considering the low boost and 60' times. What's your build and what stall converter are you running?

Hey Jeremy,

4.3 stock block, billet splayed (rpm) mains, stock nitrided crank(rpm), eagle h-beams rods, JE Severe duty pistons, JE hell fire rings, punched 4.030 on the block, Vortec ported and polished heads 2.02 valves flowed 290cfm @ .500 lift, LS1 springs, gold crane roller rockers, Custom Comp Cam, Ported and matched intake, stock throttle body, MPE Headers, MPE super cool Front mount with 3 inch piping, GT35R (limit engineering) with ATR #inch downpipe w/Tial 38mm wastegate(detroit turbo), Built Cottman Trans with the best and tcs 2800 stall converter, BIG STUFF3 engine management system.

Pic587.jpg

Pic585.jpg

Pic574.jpg

Pic648.jpg


ViciousV6
 

alwayscode390

pppssssshhhhhtttttttttttt
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

It sounds GREAT. I hope to see 11's soon :) . Nice to see 4 tenths gain from just a new intercooler and custom headers !!! Why the stock throttle body though? ---
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

nice runs ralph i forogt to call you back been real busy at work i will call you this weekend.
 

Big Mike

New member
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

Looks and sounds good, 11.50 and faster you will need a roll bar.
 

ViciousV6

400HP/550FTLB
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

Big Mike said:
Looks and sounds good, 11.50 and faster you will need a roll bar.

E-town does allow some faster cars, i have few friends running 11.2 and 11.3 with out all that safety equipment. It depends on how your car goes down the track and well under control it is.

The hardest part of the whole thing is stopping it @ the end of the track. I always use the last loop so i don't burn up the brakes.

So i am hoping to get a 11.00 out before they stop me.

I will have to get a Fire Jacket though.

Ralph
ViciousV6
 

typhoon92

Donating Member
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

Ralph If you don't mind me asking how much did MPE charge you for the headers?
 

ViciousV6

400HP/550FTLB
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

typhoon92 said:
Ralph If you don't mind me asking how much did MPE charge you for the headers?

If i remember correctly like 1495.00 for them installed! As far as i know he is not making them outright for purchase only! I think he is a little busy right so not sure how long it would take to get a set made. He has a real job now and this is his side thang.

Ralph
ViciousV6
 

Flyin Ryan

hated cuz he drives fords
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

Ralph, have you weighed the ty yet? whats she weigh?
 

ViciousV6

400HP/550FTLB
Re: ViciousV6 visits Englishtown Raceway for Test & Tune

Boostedpimp said:
Ralph, have you weighed the ty yet? whats she weigh?

Weds night we weighed in @ 3928 lbs with me in it.

Ralph
 
Top