Lots of knock!! long

J-bird

Member
Hey guys,

I've been working on this for a while now, and reasearching other things to look into. Here is the situation. My ty is mostly stock other than tuning equipment, free stuff, complete ignition, and IC pump and hoses. I have been chasing down a huge amount of knock retard.

Like I said I have changed:

Huge IC pump and replaced hard lines, temps look ok
Cap, rotor, wires, ur5's, coil, ignition module
Silicone vacuum lines
Relocated battery to rear cargo area, cone filter in its place
Ostrich, innovative wide band O2, Tuner Pro RT running code $59

I have started to tune with and things look grate other than a lot of knock retard (16-18 degrees at times). I have been playing with different things in tuning to try to remove this knock. I have good fuel pressure (50# base over 60# and rising under boost), and I Can make this thing run pig rich (11.5/1 AFR) under boost. The problem is no mater what I do I still can't get rid of this knock. I can look at my data log in TP and see where the knock is starting, then start removing timing at that point and it really doesn’t help. Yesterday I tried removing 16 degrees for the entire table (0 degrees timing advance in boost) and I still had knock. I can slowly rev the motor in N or P up over 4500rpm and not see any knock, but if I quickly stab the throttle and rev quickly I can see that it is showing KN just revving. Can this be false knock?

I need to:

Verify A\F ratio
Read plugs
Look in cylinders with bore scope
Run TEC again
Verify timing marks on balancer
Look for sources of false knock.

Is there anything you guys can see that needs to be checked, and do you think running a cooler plug (ur6's) would do anything for me?

Sorry for such a long post, thanks for reading!
 
Last edited:

Bill Z

Donating Member
Re: Lots of knock!! long

You are right to check all of your timing and tuning first.

However it could be your gas. Just try some of the octain booster in a half of a tank. If the knock goes away or is reduced, try a diffrent brand. Just because they charge more doesn't mean the product is better.

Good luck.
 

nallj92

Active member
Re: Lots of knock!! long

tank of 110 and test it then, it sounds like its false, check fuel lines and trans lines hitting stuff, and DP also
 

J-bird

Member
Re: Lots of knock!! long

I've got 3 gallons of xyleen (SP?) that I will try, anyone know the correct way to mix this stuff? Don' want to mess anything up, well anymore than it already is!

Thanks

Jeremy
 
Re: Lots of knock!! long

The best way that I have found to mix it is.

1. open can and cab door.
2. pour contents of can into said vehicle
3. light match and insert into cab
4. and this one is the most important RUN!!!

Realy it is best if mixed 1 part xyleen to 2 parts gas.

Also if you are getting knock just free reving it I would bet it is false knock.
 

J-bird

Member
Re: Lots of knock!! long

Maverick87 said:
The best way that I have found to mix it is.
1. open can and cab door.
2. pour contents of can into said vehicle
3. light match and insert into cab
4. and this one is the most important RUN!!!

Ha ha, If I can't finger it out I may just use it that way!!! :oops:
 

Bill Z

Donating Member
Re: Lots of knock!! long

Maverick87 said:
The best way that I have found to mix it is.

1. open can and cab door.
2. pour contents of can into said vehicle
3. light match and insert into cab
4. and this one is the most important RUN!!!

Realy it is best if mixed 1 part xyleen to 2 parts gas.

Also if you are getting knock just free reving it I would bet it is false knock.


You forgot the safety tip of replacing the cap on the can before you light the match. Never can be too careful.
 

J-bird

Member
Re: Lots of knock!! long

Update.

I did some looking for sources of false knock and found:

1.) DP was pressed tight against the manifold. I put a dimple in the DP but made no difference.
2.) Found a pair of pliers wedged in between the distributor and firewall. I must have left them there when installing the new ignition module. Removal of said pliers made no difference.

Yesterday I put 2.5 gallons of xylene in a 1/2 tank of gas and it really didn't help a whole lot. This morning I decided to pull the timing in the computer back to 0* advance with the higher octane fuel. The truck now has no knock, other than less than 1* at shift points.

What does this mean? I see it as meaning that the base timing at the distributor is WAY off! I have a piston stop tool coming in Monday and will check the timing marks on the balancer. I also plan to pull all plugs check them and replace with UR6's. I will probably run a can or two to sea foam through it as well. Is there anything else I should check while I'm at it? I also plan on using a bore scope down the spark plug hole just to get and idea of what it looks like in there.

Thanks,

Jeremy
 

J-bird

Member
Re: Lots of knock!! long

Ok, some progress!

I changed the plugs out, ran two cans of sea foam, and replaced the harmonic balancer. Turns out that the balancer was spun and the timing marks were about 90* off! I replaced it with a new one and set the timing, it was of about 10*.

the knock retard is alot better. I was seeing 18* at any boost level. Now I still have some knock, but its down to spikes around 7*.

The next step will be a cooler thermostat. The one in it now is a 180 and the new one is a 160*. Does this normally help knock?

I have also made some small tuning changes and it is helping.

One thing I saw when setting the timing was, when I had the timing light on it and would quickly rev the motor the timing would advance a few degrees. I had the plug under the dash unplugged, is there any mechanical advance in the stock distributor?

Thanks,

Jeremy Franke
 
Re: Lots of knock!! long

J-bird said:
One thing I saw when setting the timing was, when I had the timing light on it and would quickly rev the motor the timing would advance a few degrees. I had the plug under the dash unplugged, is there any mechanical advance in the stock distributor?

Thanks,

Jeremy Franke

I noted exactly the same thing the other day in my truck. I was setting the timing in my truck, brown wire disconnected, at idle the timing shows 0 degrees, rev the motor up and it would advance 5-6*. Is that normal?? If not, what could cause that?
 

sly dvl

Ya, it's got a Turbo
Re: Lots of knock!! long

Eric Fischer said:
I noted exactly the same thing the other day in my truck. I was setting the timing in my truck, brown wire disconnected, at idle the timing shows 0 degrees, rev the motor up and it would advance 5-6*. Is that normal?? If not, what could cause that?

Ya that's normal. It's like a default mode. Even with the tan wire unplugged it still recognizes the need for some advance. It advances a lot more then that with the tan wire plugged in.

K
 
Top