Turbo Oil Supply Using Engine Filter Assembly?

mrweelr

New member
I saw pics of a Syclone using the stock engine oil filter block to supply oil to the turbo and would like to hear from those who've done this. This looks like a simple solution, so I'd prefer to go this route instead of a remote filter assembly if it's safe to do so. I'm replacing my 60-1 non-BB turbo that has bad bearings and major shaft play with a new Turbonetics 60-1 BB oil/liquid cooled turbo and want to be sure it receives clean, filtered oil. Anyone do this and what are your impressions? Did you reuse the stock braided turbo oil supply line or have to fabricate a new one? Were any adapters needed and what size? Any info would be appreciated, thanks.

phillip19.jpg

phillip12.JPG
 

berzerker

wookie
Re: Turbo Oil Supply Using Engine Filter Assembly?

thought of doing the same to mine just haven't got around to it .can be done for pretty inexspensive .go to any hydraulic- fittings / hose -outfit such as the "parker store" if there in cali . just give them measurements / show them the old fittings from the filter housing and turbo inlet . tell them you want straflex braided hose .should be able to put together a hose for around $35 with fittings
 

mrweelr

New member
Re: Turbo Oil Supply Using Engine Filter Assembly?

I just bought the kit from RPM. Mike didn't seem to think the HOT port on the stock filter housing was filtered oil so I decided to play it safe. Ordered the new turbo today so now all I need is some 6AN braided line and some 3/8 NPT fittings for the turbo coolant lines and my truck should be running again
 

vortecfiero

New member
Re: Turbo Oil Supply Using Engine Filter Assembly?

mrweelr said:
I'm replacing my 60-1 non-BB turbo that has bad bearings and major shaft play with a new Turbonetics 60-1 BB oil/liquid cooled turbo

is the old turbo for sale ?
 

mrweelr

New member
Re: Turbo Oil Supply Using Engine Filter Assembly?

I have no use for the old turbo...someone who has the tools and knowledge could probably reuse the old CHRA and compressor cover. It's an innovative 60-1 non-BB small-shaft...had probably 3K miles on it before the bearing went bad. I'm reusing the turbine housing and it has a broken turbine blade from where it touched the housing...PM me if you really want it.

http://geocities.com/jdonavich/SyTemp/BadTurbo1.JPG
http://geocities.com/jdonavich/SyTemp/BadTurbo2.JPG
http://geocities.com/jdonavich/SyTemp/BadTurbo4.JPG
http://geocities.com/jdonavich/SyTemp/BadTurbo5.JPG
http://geocities.com/jdonavich/SyTemp/BadTurbo7.JPG
 

Daron

Active member
Re: Turbo Oil Supply Using Engine Filter Assembly?

mrweelr said:
I just bought the kit from RPM. Mike didn't seem to think the HOT port on the stock filter housing was filtered oil so I decided to play it safe. Ordered the new turbo today so now all I need is some 6AN braided line and some 3/8 NPT fittings for the turbo coolant lines and my truck should be running again

Interesting... Anyone have definitive data on whether the oil filter housing port provides filtered oil? I have my line ready to pop into the filter housing...
 

sy445

New member
Re: Turbo Oil Supply Using Engine Filter Assembly?

The stock oil line port on the engine block above where the oil filter provision is ( stock location) is filtered oil. No need to tee off a remote filter housing unless you like easier access to the line itself
 

mrweelr

New member
Re: Turbo Oil Supply Using Engine Filter Assembly?

Yup, you're basically filtering the oil twice before it hits the turbo if you're using an inline filter like the RPM kit. Cheap insurance for a $2000+ turbo.
 

Daron

Active member
Re: Turbo Oil Supply Using Engine Filter Assembly?

sy445 said:
The stock oil line port on the engine block above where the oil filter provision is ( stock location) is filtered oil. No need to tee off a remote filter housing unless you like easier access to the line itself

I guess all oil is "filtered" at some point. I wasnt wanting to "T" off the housing, I want to use the outlet ( plugged stock) that is on the housing. See picture above: "HOT" outlet...

I want to get my turbo feed closest to the filter to prevent garbage from getting to the turbo. If the filter housing outlet is being fed freshly filtered oil, the assumption would be that no matter what happened to the engine, the turbo supply would be safe. Are you saying the stock location is just a good as the housing outlet?
 

4C FED

Absolutum Dominium
Re: Turbo Oil Supply Using Engine Filter Assembly?

With 3 bypass valves, 1 in the block, 1 in the remote housing & 1 in the filter, you still have the opportunity to get junk in the turbo.
 

Daron

Active member
Re: Turbo Oil Supply Using Engine Filter Assembly?

4C FED said:
With 3 bypass valves, 1 in the block, 1 in the remote housing & 1 in the filter, you still have the opportunity to get junk in the turbo.

Exactly. Thats why I was hoping the outlet mentioned above is fed only by freshly filtered oil...
 

SY2932

Administrator
Re: Turbo Oil Supply Using Engine Filter Assembly?

DaveP6999 said:
I just looked at one that's off the car. It IS filtered, unless the bypass opens.

Another benifit to this may be that the remote filter is AFTER the oil cooler. The turbo would be getting the coolest oil in the system.

DaveP

Yup that is exactly why I have mine set up this way fed via -6 AN line. As Dave mentined, the only "danger" is if the bypass opens on the filter.
 

Daron

Active member
Re: Turbo Oil Supply Using Engine Filter Assembly?

SY2932 said:
Yup that is exactly why I have mine set up this way fed via -6 AN line. As Dave mentined, the only "danger" is if the bypass opens on the filter.

Ok, I can live with that. What tool did you use to unscrew the plug from the "hot" port? Will the stock oil feed bolt right to the housing or will I need an adapter?
 

MRKING

New Parts for Old Trucks
Re: Turbo Oil Supply Using Engine Filter Assembly?

Daron said:
Ok, I can live with that. What tool did you use to unscrew the plug from the "hot" port? Will the stock oil feed bolt right to the housing or will I need an adapter?
I am sure theres a tool that fits , but when I went to napa and other stores , I found nothing specific .

I end up using the opposite side of a thread tap and a wrench .
 

sy445

New member
Re: Turbo Oil Supply Using Engine Filter Assembly?

Daron said:
Exactly. Thats why I was hoping the outlet mentioned above is fed only by freshly filtered oil...

Yes the stock location is just as good as where you are looking to take the feed from.
They are both fed from the filter

Obviously the bypass will open due to filter blockage or too much pressure. Wether you take it from the block or the remote housing is not going to matter. If the bypass opens its possible to get hurt by unfiltered oil.

An inline filter before the turbo would be the closest thing to achieving a completely safe system
 

4C FED

Absolutum Dominium
Re: Turbo Oil Supply Using Engine Filter Assembly?

Daron said:
Ok, I can live with that. What tool did you use to unscrew the plug from the "hot" port? Will the stock oil feed bolt right to the housing or will I need an adapter?

Use vise grips.
 

SY2932

Administrator
Re: Turbo Oil Supply Using Engine Filter Assembly?

Daron said:
Ok, I can live with that. What tool did you use to unscrew the plug from the "hot" port? Will the stock oil feed bolt right to the housing or will I need an adapter?

The plug is 5/16" or 8MM. I ended up making a "tool" out of an extension that my bud destroyed when I removed the same sized plug out of the passenger side head of my old daily driver to mount my water temp gauge. The back end of a thread tap is a good idea, I never thought about that :)...

IMG_0857.sized.jpg


That addresses the size of the tool that you will need to remove the plug. The plug itself is 3/8 X 18 NPT thread. AFAIK, there isn't an adapter that will drop from 3/8 pipe down to the size of the stock oil feed line.

IMG_1733.sized.jpg


Even if you could get an adapter, you would probably end up having three 90 degree bends in the oil feed line unless you felt comfortable straightening out one of the 90 degree bends on the stock oil feed line... I laid my stock oil feed line across the front of the motor and it is plenty long enough:

IMG_1735.sized.jpg


I can't take all the credit for my set up since I copied my bud's exactly for the reasons cited earlier. Incidentally, he's the one that destroyed my extension that became my 5/16" 8MM plug remover. Sometimes one hand washes the other
icon_lol.gif
!
 

4C FED

Absolutum Dominium
Re: Turbo Oil Supply Using Engine Filter Assembly?

Std. vise grips. I removed mine recently when I installed a mechanical oil pressure gauge. There is enough of the head sticking out to clamp the vise grips onto and start turning.
 
Top