Replacement of window inner seal (felt strip)??

James Thomas

"NO CLASS"
Ok fellas, the inner window seals (felt strip) are attached to the top of the door panels (and the leather / cloth trim) with some realy big ass staples. What's the best way to replace these? I have no clue where to get staples or the stapler to replace these like the factory, so......... what have you guys done about this? It's #5 in the pic below.

TIA
________
James


 

kentuc

Member
Re: Replacement of window inner seal (felt strip)??

I used some small pop rivets. 3 or 4 on each.
 

AWD

New member
Re: Replacement of window inner seal (felt strip)??

are you trying to replace the whole piece or just the felt strip on the front?
 

James Thomas

"NO CLASS"
Re: Replacement of window inner seal (felt strip)??

AWD said:
are you trying to replace the whole piece or just the felt strip on the front?



Ummmm...... not sure I understand? As shown in the parts pic above, #5 runs the whole length of the top of the door panel / window so..... yea I guess the "whole piece" cause it's a one piece strip held on with those big ass staples. Got an idea?

_________
James
 

James Thomas

"NO CLASS"
Re: Replacement of window inner seal (felt strip)??

kentuc said:
I used some small pop rivets. 3 or 4 on each.



Thanks for the idea! I'll look at that but was there a clearance or "rub" issue on the back side?

Thanks :tup: !!

__________
James
 

ShuggsRR

Donating Member
Re: Replacement of window inner seal (felt strip)??

I bought the whole window kit and needed everything but the inside felt. I have a set of inside felts of you need it. It comes with screws to attach it.
 

TYPHOOL7

Post Hawk
Re: Replacement of window inner seal (felt strip)??

ShuggsRR said:
I bought the whole window kit and needed everything but the inside felt. I have a set of inside felts of you need it. It comes with screws to attach it.
what exactly did you buy, im in need of that service too.
 

sy445

New member
Re: Replacement of window inner seal (felt strip)??

That felt thing kind of sucks to replace unless u like spending time on things u will never visually notice. I wish i had replaced mine though when i had the door apart to put leather inserts in. It wasnt torn to bad til now. I used saftey wire threaded through the staple holes to put it back in cuz i couldnt find any other solution for the monster staples. The wire has no rubbing issues either
 

MadPSI

Member
Re: Replacement of window inner seal (felt strip)??

I guess I'll post again, since mine disappeared earlier...

I used some heavy duty staples from my staple gun to hold the piece on. I clamped the piece in place using some vice grips and drilled a bunch of holes (spaced approx. as wide as the staples) using a dremel. I then fed the staples through the holes from the inside out and bent the tabs over while compressing the surrounding area with needle nose pliers. After bending the tabs I clamped a large vice grip on each staple and let it sit for a few minutes. I used about 10 staples per side and it worked very well.
 

James Thomas

"NO CLASS"
Re: Replacement of window inner seal (felt strip)??

ShuggsRR said:
I bought the whole window kit and needed everything but the inside felt. I have a set of inside felts of you need it. It comes with screws to attach it.



Thanks Shuggs, I really appericate that! My felts are primo but I'm swapping out a cracked door panel and need to transfer my felts and leather trim over. If the kit came with screws, were they just short sheetmetal type?

_____________
James
 

James Thomas

"NO CLASS"
Re: Replacement of window inner seal (felt strip)??

MadPSI said:
I guess I'll post again, since mine disappeared earlier...

I used some heavy duty staples from my staple gun to hold the piece on. I clamped the piece in place using some vice grips and drilled a bunch of holes (spaced approx. as wide as the staples) using a dremel. I then fed the staples through the holes from the inside out and bent the tabs over while compressing the surrounding area with needle nose pliers. After bending the tabs I clamped a large vice grip on each staple and let it sit for a few minutes. I used about 10 staples per side and it worked very well.


Ok now I didn't think about doing that...... thanks :tup: !

_________
James
 
Top