Lack of Volume

Aeroking

e.i.
I ran a pityful 14.5 last night. trap speed was 89ish. My 60' times were in the 1.8s. and ran an 1/8th in 9 flats.

Bearing in mind that my only mods are a 3" exhaust, manual boost valve, and IC pump.

and i have regular 4.3L flat-top pistons.

i was leaving the line at 7psi.

So i'm guessing i lose all my top end because of the 9.5-1 compression ratio... right?
 

SY756

New member
Re: Lack of Volume

Are you running Datamaster or any kind of logging software? How much boost are you running? My first thought is you are detonating. Just a thought,,,,with that compression ratio I bet that's the problem.
 

Aeroking

e.i.
Re: Lack of Volume

didnt have my datamaster running at the track.

I run 105 octane unleaded, because on pump gas i detonate at about 12psi.

i was running stock 14.5psi at the track.
 

MikeRenz

not stock
Re: Lack of Volume

it was humid as hell last night here in state college...i can only assume it was pretty lousy weather for racing last night over by you....i'm sure that had something to do w/ it.
 

Aeroking

e.i.
Re: Lack of Volume

its been said by the track's operators that there is an uphill slope to the track (Quaker City, Salem OH). and also, in my 3 Trans Ams, i run 2-3 tenths slower there than at other tracks.

plus yesterday it was 80 degrees, and drizzling raining, so it was really humid.


but now i have a baseline for next spring when the other motor goes in.
 

dgoodhue

BuSTeD 4.3
Re: Lack of Volume

Aeroking said:
I ran a pityful 14.5 last night. trap speed was 89ish. My 60' times were in the 1.8s. and ran an 1/8th in 9 flats.

Bearing in mind that my only mods are a 3" exhaust, manual boost valve, and IC pump.

and i have regular 4.3L flat-top pistons.

i was leaving the line at 7psi.

So i'm guessing i lose all my top end because of the 9.5-1 compression ratio... right?

11-12 psi is rough equivalent in in tems of cylinder pressure as 15psi in the SyTy 8.35:1 (stock) compression. The 9.5:1 motor should not be affecting your top end at all. Infact it probably runs better with racegas at 15 psi than stock motor at 18psi, becuase the stock turbo is more efficient at that boost level. If you running higher octance and run more than 12 psi of boost, you have some issues to resolve. I would expect on a cool night mid 13's form your truck at 12 psi and MPH of 98/99. If your running more boost & race gas I would expect to see more mph and the truck dipping into the twelves. You are probably off a full 10mph. It should be running way better than that and that is why your buddy's LS1 truck is beating you.

I know you keep saying your going to get a new motor, but I would presonally try to indentify the problem with the current motor. You don't want to have that same problem with the new motor. Get a scan tool on it and start getting some expereince debugging the problem. At the very worst you might screw up the regular motor but you were going to replace that anyways..
 

Aeroking

e.i.
Re: Lack of Volume

when they setup the bracket races I was able to hold 10psi of boost at the line with the rear tires spinning, but they held the tree, and i started to wheel hop, so i shut it down.

other than that, i left at 7psi, with the truck jumping sideways.

i did an AWD burnout each time in the waterbox. (which is easy there because the staging lanes/waterbox are at about a 30degree angle upwards towards the track.)

i'll run a DM tonight on a spirited street drive. and make a couple passes at the other local track (the fast one).
 

beastmode

New member
Re: Lack of Volume

ya we both did pretty damn pitiful buddy.... i cant believe how much fuggin timing my trucks pulling out cause of that ****in knock sensor, im losing like 8 degrees... we both have wounded wings lol

that compression i think is def hurtin you. i know when guys are goin turbo wit the LS motors they go LQ4 instead of LQ9 cause the compression on LQ9 is higher... im sure that has alot to do wit it. in which case you should think about changin your heads when you do hte new motor... wouldnt those be vortec heads?
 

Aeroking

e.i.
Re: Lack of Volume

beastmode said:
ya we both did pretty damn pitiful buddy.... i cant believe how much fuggin timing my trucks pulling out cause of that ****in knock sensor, im losing like 8 degrees... we both have wounded wings lol

that compression i think is def hurtin you. i know when guys are goin turbo wit the LS motors they go LQ4 instead of LQ9 cause the compression on LQ9 is higher... im sure that has alot to do wit it. in which case you should think about changin your heads when you do hte new motor... wouldnt those be vortec heads?

doubtful about the heads, i'll keep my stock heads. might change later, but for this winter, i'm just doing the bottom end.


so Dave, should i turn my boost down to 12?? with the stock ECM set for the lower comp., wouldn't running 15psi (which like you said is like 18psi on a stock motor), wouldn't that run the engine lean... should i be adding more fuel?? i have a billet AFPR on the truck, and its set to 42psi.
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Lack of Volume

other than a poor tune or running poorly, there is no reason a motor with higher compression and more boost shouldn't be making more horsepower..

get a few runs in with datamaster, it will tell you where you are and why it is running poorly.
 

dgoodhue

BuSTeD 4.3
Re: Lack of Volume

Aeroking said:
so Dave, should i turn my boost down to 12?? with the stock ECM set for the lower comp., wouldn't running 15psi (which like you said is like 18psi on a stock motor), wouldn't that run the engine lean... should i be adding more fuel?? i have a billet AFPR on the truck, and its set to 42psi.

For pump gas (assuming no Alky), you might want to turn it down to 12 psi. What do you have for a Chip? MAP sensor? You might want more fuel pressure, because the MAP sensor read pressure and since you have a denser air charge in the cylinders (higher compression) it will need more fuel to ignite. Is 42 psi static Fuel Pressure (vacuum line not attached)? Have you upgrade the Fuel pump?

What you really want to do is give the engine what it wants not an educated guess of what you think it needs.
 

James Thomas

"NO CLASS"
Re: Lack of Volume

Tip: You can make more power with a bit more compression and the same boost levels, also better spool and or maybe not as much stall, but......... you gotta tune it. My current build in process will not be stock compression and thats my story and I'm stick'in to it! Maybe Nolan will chime in?

______________
James
 

Aeroking

e.i.
Re: Lack of Volume

my FP is 42psi with the vac hose removed. I have a 255 intank fuel pump, stock injectors, and a pitbull chip with a stock 2bar map.

but again, i can "workbench" tune here from my office desk all day, but until i get in the truck, i can just speculate.
 

Aeroking

e.i.
Re: Lack of Volume

ok... question, my spare block is being cleaned, and i havent ordered my internals yet.

what kinda compression would i be looking at with stock heads, stock bore & stroke, and +21cc dished pistons???

if higher compression is the way to go, then should i plan for flat-tops, or go low comp. with dished...
 

James Thomas

"NO CLASS"
Re: Lack of Volume

Good questions and many of these depend on your build combo. RPM, cam profile, bore & stroke, actual deck height, boost levels, will you be using engine coatings, even the head gaskets thickness and on and on but first I would start playing with a compression calc. tool like: http://performanceunlimited.com/documents/boostcompression.html
http://www.csgnetwork.com/compcalc.html

I know that everyone has there reasons for doing things (or doing things different) but to build a new engine and use stock heads is a waste IMO. At the min, a set of L-35's will give better performance and if you are going to be playing with comp. and boost, I think a Vortec swap is mandatory due not only to the better flow and performance (above and beyond the L-35's) but also the much better chamber design and less chance of detonation with higher cyl. pressures :2cents:

______________
James
 

dgoodhue

BuSTeD 4.3
Re: Lack of Volume

Aeroking said:
what kinda compression would i be looking at with stock heads, stock bore & stroke, and +21cc dished pistons???

if higher compression is the way to go, then should i plan for flat-tops, or go low comp. with dished...

I think the stock heads are either 64cc or 68cc chambers. You can calculated it the CR with the rest of the numbers, you will also need the thickness of the header gasket as well. Vortec suposedly have a slightly smaller chamber

I am going to be using a Vortec short block with 9.0:1 Compression. Even though I am confident I can use 9.0-9.5 CR, I will probably use low compression pistons when I build up short block.
 
Last edited:

Aeroking

e.i.
Re: Lack of Volume

i'm gonna try to have my shortblock assembled before i store the truck in the garage (at which time i'll swap motors). But yeah, definetly +21cc dished forged pistons.

top end will be a later concern, cause i'll go with Vortecs, but i'll have to have the intake adjusted, so... I'll worry about that when i get there.

i might be back to the track once more this year, but other than that, the truck leaves the garage once a week for a car show.

I just started my truck and it was shaking, so i'll pull my plugs tomorrow and check them.


edited: went to the 2nd link, and with Vortecs and the TRW pistons its around 8.45:1 CR, which is damn close to stock.
 

Aeroking

e.i.
Re: Lack of Volume

DAVE COULD YOU MOVE THIS TO THE TUNING SECTION

so with flattop pistons i have a smaller combustion chamber, and 9.5:1 CR.

So to get a correct AFR of 14.7:1 in a 9.5:1 CR engine, i would have to stay around 12psi, with the stock FP of about 42psi, correct???

And should I boost it to 15psi, i should richen my mixture to keep the 14.7:1 AFR, correct???

With the computer reading 15psi in the plenum, and with the smaller combustion chamber it would be like running 18psi, so the ECM will add enough fuel for 15psi, but theoretically the charge is 18psi, so shouldn't I have to add more fuel to maintain the AFR???

(ALL with a Pitbull chip, and 2bar MAP, and doing this without a wideband O2)
 
Last edited:

It's just a six

Super Member
Re: Lack of Volume

I know when I ran a Pittbull street chip I was running 50 psi w/ vacuum hose off, when I did get an adjustable reg & a 255 HP pump in,my MPH went up 3 MPH or so, it was running out of fuel.

The Pittbull chip/2 bar map sensor, will not read anything above 14.7 PSI, luckily it is a rich safe chip, that is when I ran 18-19 PSI boost & 50-53 PSI on the fuel pressure.
A/F ratios were around 12.5 .
14.7 or so ratio is for when you are light throttle & cruiseing.
 
Top