Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

Black Knight

I Glow Therefore I am
I was over looking at this guys racecar the other day and he was taking off his valve covers. When he pulled the breather out I noticed he had a green
Scotch-Brite pad stuffed in there. I asked him why he did that and he said that it allows the motor to breath and keeps the oil from coming out.

I've never heard or seen anyone doing this before and just wondered what peoples thoughts on it are. I have that issue with oil leaking out of the breathers, esp. when I'm running in boost.

My biggest concern is some of the little particle's coming off the pad and getting in the motor and oil. If you've ever handled one you'll know what I mean, the brand new ones leave small fibers everywhere, so you'd probably need a used one.
 

Flyin Ryan

hated cuz he drives fords
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

I would wonder why your getting oil coming out of your breather.. does that mean you have higher then normal crank case pressure?? Mine doesn't pull any oil out but only has a breather on the driver side hows your setup?
 

Black Knight

I Glow Therefore I am
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

I've always wondered about that also, it was Waller's suggestion that I ditch the PCV setup and go to both breathers years ago. I've always had an issue with oil leaking out ever since I did it, but all the old cars I've ever had always did it also so I never thought much of it, it just bugged me to have to always wipe it off and constantly check my oil level.
 

Black Knight

I Glow Therefore I am
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

Boostedpimp said:
I'd have to go back to what I said way back to you in the thread below
http://www.syty.net/forums/showthread.php?t=39956&page=2&pp=15&highlight=pcv

:rotf: Damn, I didn't even remember that.

I had alot of problem with the oil long before the I took the PCV's out. It used to push so much oil out that it coated the inside of my first turbo and covered everything inside the T/B and intake manifold, like it was almost cycling oil through there.

So what is a cause of excessive crank case pressure? Tolerances too high in assembly?

I do know that when I did a compression test the one time before I took it apart, the compression was about 160psi across the board, which seemed high to me since alot of what I've seen over the years was 120-130psi. Maybe that's the cause of it pushing so much oil out, but then why is the compression so high, again tolerances?
 

Black Knight

I Glow Therefore I am
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

Anyone got any thoughts or opinions on this Scotch Brite idea?
 

sy445

New member
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

Excess crankcase pressure is from cylinder pressure blowing past the rings, or the crankcase is not breathing enough. Usually blowby though. You may get higher compression readings from a small cam or the lack of overlap from a turbo cam. I might be worried about the scotchbrite "dusting" or falling apart over time. Prob not going to ever hurt anything but why chance it.
 

Black Knight

I Glow Therefore I am
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

sy445 said:
Excess crankcase pressure is from cylinder pressure blowing past the rings, or the crankcase is not breathing enough. Usually blowby though. You may get higher compression readings from a small cam or the lack of overlap from a turbo cam. I might be worried about the scotchbrite "dusting" or falling apart over time. Prob not going to ever hurt anything but why chance it.

As far as I know the cam is still a stock one ( that's why I hate buying stuff someone else put together, I have no idea what I'm dealing with ).

There's probably no way to do anything about any of the above stated things either with the motor back in the truck?
 

rodent

Member
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

What about doing a catch can setup?
 

Black Knight

I Glow Therefore I am
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

Considered it, just never looked into it too much, it was just easier to through some breathers at it. I might have to investigate this more.

You got any leads to decently priced setup?
 

TYHOGG

Active member
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

I had a similar problem. Took the motor apart and 2 of my pistions where shattered. Only the rings where holding them together. Was getting the excess oil and compression readings from the blow-by.
 

rodent

Member
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

Black Knight said:
Considered it, just never looked into it too much, it was just easier to through some breathers at it. I might have to investigate this more.

You got any leads to decently priced setup?

I'll be installing something like this on my setup:
Element%20Competition%20Catch%20Can.jpg

Think I paid $30 or $40 for it at my local speed shop. Elements (pictured above) wants way too much for theirs. You can run lines from both valve covers to it.
 

gjp

another post whore
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

I too am getting oil on the covers. I feel no air comming out the covers even at 2000rpm. When I had the heads off the pistons looked fine. Oil could be because I have no baffles on my rpm covers. Looking at using a catch can as I am getting oil into my TB. Have any pics of the can installed?
 

Deanzsyclone

New member
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

rodent said:
I'll be installing something like this on my setup:
Element%20Competition%20Catch%20Can.jpg

Think I paid $30 or $40 for it at my local speed shop. Elements (pictured above) wants way too much for theirs. You can run lines from both valve covers to it.

I just receantly installed the above can with the high end fittings, seems to work pretty good, no more oil on my valve covers. It used to go down the valve covers and ocasionaly hit the header causing smoke from the engine compartment. That happend mostly when I got it under boost. Which was 79% of the damn time. No more smoke now, but my dumb ass mounted the can where the stock ac acumulator used to be and now the fumes from the airfilter (pictured above) come out and seem to go into the intake to my cabs ventalation system. You know the sloted vents right under the windwhield wipers. :roll:
I'll put an extension on the filter and seperated it from the canister and move it down low on the firewall or something. Unless someone has a better idea. I'm sure not running a line from the filter to the input to the turbo, that thing has a vacum that scares the crap out of me.
Just the other day I told my buddy how it seems to suck your hand in rather violently under good rpm so he said ohh really, and put his hand down by the intake of the turbo so, I reached over to the throttle body and goosed it, it was really funny the look of terror on his face when it damn nearly swallowed his hand into the intake. He's lucky thiers a screen over the turbo's intake. :rotf:
 

Black Knight

I Glow Therefore I am
Re: Anyone have any experience with putting a Scotch-Brite pad in thier valve cover?

rodent said:
I'll be installing something like this on my setup:
Element%20Competition%20Catch%20Can.jpg

Think I paid $30 or $40 for it at my local speed shop. Elements (pictured above) wants way too much for theirs. You can run lines from both valve covers to it.

thanks for the heads up, ill check into one.

Nice story Dean, funny shiznit :rotf:
 
Top