I Feel Really Lucky - Turbo Removal

WyoSyclone

Active member
Went to remove my stock turbo this morning (wastegate frozen shut), and had about the best luck I could ever hope to have... I'd sprayed all the exhaust/turbo bolts a few weeks ago with PB and again this morning. From start to finish I had the old turbo off in about 45 minutes - no broken knuckles, and more importantly, no broken studs!

Now I just need to get my new turbo in from Mike (hint, hint......), put it together and start tuning with $59 again.

Having read all the horror stories on the forum about taking the turbo off I feel REALLY lucky.
 

gjp

another post whore
Re: I Feel Really Lucky - Turbo Removal

mine was not that bad too. 95k and it came off easy. Not that easy but I broke nothing. Including myself.
Its nice when something goes easy on our trucks. I just spent the whole morning removing my zq8. it was only in there for 2 months but the pitman arm was stuck. I guess you got all the good luck for the day.LOL
 

WyoSyclone

Active member
Re: I Feel Really Lucky - Turbo Removal

gjp said:
I just spent the whole morning removing my zq8. it was only in there for 2 months but the pitman arm was stuck. I guess you got all the good luck for the day.LOL

I'm going to do the zq8 and steering shaft next.... I was surprised at how much easier it looked with the CAC dropped out of the way... I was thinking about renting a puller from NAPA for the pitman, using some heat, and a BFH .... did you do that?
 

gjp

another post whore
Re: I Feel Really Lucky - Turbo Removal

last time the pitman fell off the steering bar. I have the puller to take it off the box. You cant get the puller in there while its attached to the bar. I removed the arm on the passanger side and the link that holds the bar to the drivers adjustable arm. I was able to remove the box and slide it foward to get the puler off. I was not able to get the pitman off the bar. I have the right tools but I could not break it lose. In all It took me about 2hours start to finish. That included removing the A2A and volvo fan.
 

Black Knight

I Glow Therefore I am
Re: I Feel Really Lucky - Turbo Removal

WyoSyclone said:
I'm going to do the zq8 and steering shaft next.... I was surprised at how much easier it looked with the CAC dropped out of the way... I was thinking about renting a puller from NAPA for the pitman, using some heat, and a BFH .... did you do that?

You shouldn't need any heat. I do them all the time at work, yes some can be harder then others, but in the hundreds I've done never needed heat.

1. Take the pitman arm loose of the center link, take nut off and hit the side of it with a hammer. If no go you'll need a pickel fork.
2. Turn the pitman so it faces the windsheild washer bottle ( it may be a little more or less, but I find it easier if it's not pointing straight back but more at an angle towards the drivers side.
3. Unbolt box from frame. If your changing boxs also, break the lines loose before you unbolt it from the frame.
4. Push box back towards the rear of truck, at which time you should be able to get the nut off with an impact and get your puller on it.

It's been a little while since I've done a SyTy, but it's a GM and they're all setup pretty close to the same, so it may vary a little but that's the jist of it.
 

gjp

another post whore
Re: I Feel Really Lucky - Turbo Removal

hammer or fork would not get mine off. And it was only on for a few months.
 

gjp

another post whore
Re: I Feel Really Lucky - Turbo Removal

Black Knight said:
Do you want to borrow some of my man strength? :ninja:
LOL. :rotf:
with all the anger I have right now, I would have thought I could have ripped it off.
 

Don W.

Stab it and steer it
Re: I Feel Really Lucky - Turbo Removal

I know that nut is in a bad spot, but... If you can get a puller on it, cinch up on the puller then give the puller bolt a good whack it might work. At least I've had good success with that method. (But not on that nut.) :2cents:
 

WyoSyclone

Active member
Re: I Feel Really Lucky - Turbo Removal

Yup, best luck I've had is putting a puller on it then giving it a whack with a 3lb sledge... usually pops right off.... if the puller isn't available one of the little micro torches will make it fall off if you just heat a quarter inch strip...

amazing how much easier it is to work on these things if you just take the time to pull a few things off first... like the CAC
 
Top