will the 700r4 ever be "bulletproof"

fivetodrive

CRISPY
Re: will the 700r4 ever be "bulletproof"

It seems like the future of the 700r4 will be the restomod group of people. All the time I hear of guys with 60's era camaro's and the like looking for an overdrive tranny or directly for a 700r4 or 4l60. They like their carbs and want overdrive. Even alot of the jeep guys want the overdrive tranny's and have already converted to a 4.3 or 350 in their jeep...
 

George Blake

DONATING MEMBER
Re: will the 700r4 ever be "bulletproof"

Not trying to go to deep into it but the 5 pinion planetaries were done for a couple reasons. The housings are made of powdered metal and pressed. The new planetaries were less expensive to produce and could be done faster. The extra pinion was added to disperse the force around the housing to prevent damage to the housing due to material. Doesn't really make it stronger as the housing can still only take so much. The true high strength planetaries are in the 80e and TH400's and they are the straight cut "rockcrusher" gears. Unfortunately they make a lot of noise and the knock sensors probably would not like it. Helical gears like to thrust. Straight cuts carry more load since they don't thrust anywhere. I've seen several helical housings where the gear actually cuts down into the housing. It's usually due to a lubrication failure though.
 

George Blake

DONATING MEMBER
Re: will the 700r4 ever be "bulletproof"

ashman said:
not everyone here does nonstop boost launches.

some of us actually baby our trucks and treat them with respect. not that i NEVER boost launch. it's just rare.

It only takes one time:tup:
 

Daron

Active member
Re: will the 700r4 ever be "bulletproof"

both my 700r4s lasted past 100,000 miles. The sy tranny was still putting up the good fight at 115,000. That thing had been raced non stop from 50,000 miles on.
The Ty is still working sweet at 110,000.
 
Last edited:

cameronsclone

New member
Re: will the 700r4 ever be "bulletproof"

If you're worried of the value of the truck dropping from a tranny swap, then shouldnt you also be worried about what beating on it and "building" a transmission too? IMO building your transmission is like building your engine. If you get new pistons, rods etc. it's like getting a cryoed tranny parts or beffed up parts in the trans. If you ask me, they can both raise or drop the value at the same rate.
 

Ross L

Member
Re: will the 700r4 ever be "bulletproof"

IMO a Syclone should have a 700(good or bad thats what they came with) just like it came with a 4.3(should I swap it because there is something better?) :( There have to be many more 700's out there compared to the 200(the buicks were the only perf car that used it). I would guess in the 100K range. I was only wondering "if" the right hard parts became available would the 700 be a good transmission. I see where several others have had good luck with theirs. I'm very easy on this truck so I guess I should stop worrinig about it and just keep enjoying it :D Thanks for all the input!
 

skwayb

NWSTP
Re: will the 700r4 ever be "bulletproof"

My Ty was pretty much stock. The only thing different on it was I had the Bigger Upper ATR IC and the ATR Front Mount IC in from of the radiator and bigger water pump. I had a big Tranny cooler and deep tranny pan also. I only raced it once at Nats 2000 and just driving it around town in the summer in stop and go traffic 2 years ago toasted the tranny. It just started to slip in every gear and shifting erratically. I didn't want to dump a ton of money into a solution that will just end up breaking driving around in traffic. So I went to the 80e. Best mod I have every done.
 
Top