first question from a new guy(axles)

singledownloop

New member
I need to shorten the front axle to the 2wd length,or 4" as you know.I'd like to find some clear pics of both axle halfs.i plan to remove joint,shorten shaft,do any machining neccessary to shaft,reinstall joint.Are both the drivers side and passenger side axles the same length in the bravada?I'm building a custom frame and i realize it would have to be 4"narrower.A stock width 2wd rearend fits perfecty in this car with 8.5x17's on it.I need the same width in the front to run the same wheels and tires on all 4 corners.
 

JSM

Active member
Re: first question from a new guy(axles)

Yes both axles are the same.

You would have to cut and respline the shafts in order to do it. I am assuming you said custom frame so that is custom suspension also? Lots of geometry things to consider, if the axle will be long enough for suspension travel, angle of joints, lots of changes to consider. Seems like a lot to do just to avoid 2 different offset rims. Most custom cars run wider rear rims anyways.
 

singledownloop

New member
Re: first question from a new guy(axles)

You make a valid point.Resplining the axles wouldn't be a problem.Do you know what the total length of the shaft in an axle is?I plan on using all stock suspension mounting points.If i feel the angles would to severe my second option would be just to narrow the front third member on the passenger side.What i mean by that is to narrow the complete frame from the passenger side to the drivers side by 4" then take that 4" out of the tube/shaft that the passenger side half shaft attachs to.Do you know of any pictures available to show the shaft that runs through that tube?Is it splined on both ends?That very much for your input.
 

JSM

Active member
Re: first question from a new guy(axles)

If you narrow the axles you will need to narrow the mounting points of the frame also otherwise the axles won't reach the spindle. Then you get into clearance issues with the motor.

I suspect you have not really researched this completely yet. Your best to just leave it alone and get different offset rims, or widen the rear to match.
 

singledownloop

New member
Re: first question from a new guy(axles)

I respect what you are are saying.I'm here on this board to get some syty specific parts information.I've been a fabricator for just shy of 3 decades.What you may or may not be considering is when when you replace the very thick stock rails with 2x4 rectangular stock you will gain the 2" per side.This is why i made no mention of changing a-arms or the geometry of the suspension,why fool with specs G.M. has spent millions of dollars developing.I guess an easy way to visualize it for you or anyone reading this post would be to take a overhead view of the frame/suspension.Squint your eyes and imagine sectioning the 2" from each side of the frame.See how that in turn moves the suspension in towards the centerline of the frame 2"?I'm not real good at teaching only doing so i'm sorry if this isn't very clear.We build streetrods/hotrods/customs for a living this isn't a hobby or a sideline.Again thank you very much for your input..........Greg
 

JSM

Active member
Re: first question from a new guy(axles)

Not saying it can't be done or ever questioning you background. I have just studied the syty suspenion now for 5 yrs, have designed my own coil-over kit/a arms (several owners are using them) etc.

Just trying to bring to the surface some of the things and troubles you will run into. I will leave you be though.
 

'JustDreamin'

Dream: 6LV8 Turbo Bravada
Re: first question from a new guy(axles)

Hey Boss....

Just trying to clarify exactly in my mindwhat you're doing, so that the response I give is accurate.

You've got the S10 4wd IFS setup, and are looking to narrow it approximately 4" for use with a custom frame on a hot rod, correct? And the suspension layout (upper and lower arm lengths / geometry) isn't changing, correct?

If that's the case, then the 2 halfshafts (driver's side and passenger's side) won't change at all (because the inner CV joint location needs to lie in between the upper and lower A-arm pivot points, which it does with the stock geometry).

What that means is that most or all of the 4" you need to trim out of the front end needs to come out of the passenger's side axle extension (section from the diff over to the framerail). The reason that I say most of it has to come out of the pass side is that there really isn't any material to remove from the driver's side. This does mean that the front diff needs to move 2" closer to axle centerline, which may not work without offsetting the engine towards the passenger's side (because of oil filter / bellhousing clearance.)


Here's another thought to ponder. GM's suspension design is functional, but certainly not optimized for a hot rod. Taking that suspension design and narrowing the frame mounting points by by 4" may not be a great idea, due to impact upon things like roll center, and steering geometry (specifically Ackerman angles). I'm not sure what impact it would have without running some analysis (which I'll leave for you), but I wouldn't expect that GM's geometry would be ideal for your setup.

Another thing to consider: What is the offset of the front wheels? The reason the front wheels on the 4wd's use such positive offset is to get the scrub radius down close to zero. Basically, if the contact patch of the tire and the spindle pivot axis (through the 2 ball joints) line up, you'll limit torque steer. Make the scrub radius larger and steering effort and torque steer a much more pronounced effect.

Hope that I'm not preaching to the choir and that these are all things you've considered already.

'JustDreamin'
 

singledownloop

New member
Re: first question from a new guy(axles)

You gentlemen have replied to my post in a very well thought out and informative manner.I do sincerely appreciate your concerns.I may possibly have been wiser to ask specific questions to the parts i need information about.We all know that on these forums if you are vague about your project you get a lot of responses asking why or what are you working on.I realize from my research that this site is a goldmine of syty information.
 

'JustDreamin'

Dream: 6LV8 Turbo Bravada
Re: first question from a new guy(axles)

singledownloop said:
You gentlemen have replied to my post in a very well thought out and informative manner.I do sincerely appreciate your concerns.I may possibly have been wiser to ask specific questions to the parts i need information about.We all know that on these forums if you are vague about your project you get a lot of responses asking why or what are you working on.I realize from my research that this site is a goldmine of syty information.

Certainly specific questions are alot easier to answer, but harder to ask....

SyTy.net certainly is a goldmine of information. And some of it is applicable to things other than Sy's and Ty's. For example, these guys were instrumental in me figuring out what bits and pieces to put in my project truck (6.0 / 4L80E / NV246 in a '99 Bravada, keeping AWD). Also, approached correctly, they have a vast array of knowledge (beyond just Sy's and Ty's) that they are very happy to share. They're also a very tight knit community. Only site I know of that even comes close is the Hybrids / Conversions subforum on LS1Tech.com, and they're not nearly the "community" that this group is.

I'm not sure whether I helped answer your question or not. But hopefully it was helpful. I know Jeff (JSManufacturing) is pretty knowledgeable about drivetrain & suspension stuff on these trucks as he's developed a coilover conversion and the 4L80E / BW4472 conversion pieces.

'JustDreamin'
 

'JustDreamin'

Dream: 6LV8 Turbo Bravada
Re: first question from a new guy(axles)

singledownloop said:
Do you know of any pictures available to show the shaft that runs through that tube?Is it splined on both ends?That very much for your input.

I don't have any pictures. I also think it depends upon the year of the truck (S10 platform specifically).

I think the Sy / Ty and 1st gen S10 run half shafts with a mounting flange at the ends of the differential center section. At least that's what I recall seeing in some pictures.

My '99 Bravada has halfshafts that are splined at the end (male) and fit into a female splined socket in the center section. So the passenger's side axle on my truck is female spline on the halfshaft end and male spline on the differential end (where it plugs into the spider gear). I do not know whether the 2 halfshafts are identical or not (could be).

'JustDreamin'
 
Top