New harness in the Sy and now it won't start

bg_bls

New member
I had a rat get under the dash of my Sy and chew up some wires.
rant3.gif
So I decided to replace the dash harness as well as the engine harness. I think the harness was for a Typhoon since a few plugs are different. But anyways, on to the problems...

The first problem I have is no priming of the fuel pump when I turn on ignition power. I also have low fuel pressure and the injectors never fire when cranking. I swapped the relays by the brake booster and no go. If I run 12V to the plug above the dizzy the pump fires right up and I get good fuel pressure but the injectors still don't fire. I also checked both the ECM fuses. What else can I check?

Second thing I have noticed so far is the check engine light is not coming on when I turn the key. I thought I remembered it coming on then going off if everything checks out.


There are a couple wires coming out by the fusebox that are really short and I cannot find a place for them. Not sure if it is related or not. My buddy is gonna send me over the pics and I will post up the wires I am speaking of.


Thanks for any help,
Brian
 

bg_bls

New member
Re: New harness in the Sy and now it won't start

Ok looks like I found part of the problem.I am heading over to the shop now to check it out. In this thread: http://www.syty.net/forums/showthread.php?t=53825


DaveP6999 said:
Yes.

I assume you have a Syclone. There is a harness that comes up the LH frame rail. It plugs into the bulkhead connector above the front lamp harness. Has 6 terminals. The Grey wire is the fuel pump. If you end up using a Typhoon IP (inside) harness, you will have to move these 6 wires from the long skinny connecton on the side of the fusebox to these locations. The Typhoon harness to the fuel pump and rear lights runs inside the car.

This is the biggest differrence between Sy and Ty chassis and Instrument Panel wiring. And it's only 6 wires :tup:

DaveP


Any idea's why the injectors aren't firing??
 

supersports10

New member
Re: New harness in the Sy and now it won't start

what did you do with the old sy harness?? how much do you want for the old sy harness, inside and out???
 

bg_bls

New member
Re: New harness in the Sy and now it won't start

supersports10 said:
what did you do with the old sy harness?? how much do you want for the old sy harness, inside and out???

I am still using it right now just for comparisions sake. Once I get this sorted out I will shoot you a PM. I am not sure what exactly is wrong with it, but I was having weird intermittent issues.


Brian
 

supersports10

New member
Re: New harness in the Sy and now it won't start

bg_bls said:
I am still using it right now just for comparisions sake. Once I get this sorted out I will shoot you a PM. I am not sure what exactly is wrong with it, but I was having weird intermittent issues.


Brian

10-4:tup:
 

jwaller

Evil Genius/SyTy Guru
Re: New harness in the Sy and now it won't start

the ty under dash harness will have a few extra things. such as the remote mirror stuff. the ty harness will also have different connectors for the AC compressor and the ac relay harness on the firewall by the ac box. as for not getting fire. is the ECM powering up? are you getting check eng lights when you turn the key on? have you checked to see if the pumps getting voltage? is it only with the key on or during cranking as well? if you swapped them out directly then you should have no issues. somethings not plugged in somewhere.
 

bg_bls

New member
Re: New harness in the Sy and now it won't start

jwaller said:
the ty under dash harness will have a few extra things. such as the remote mirror stuff. the ty harness will also have different connectors for the AC compressor and the ac relay harness on the firewall by the ac box. as for not getting fire. is the ECM powering up? are you getting check eng lights when you turn the key on? have you checked to see if the pumps getting voltage? is it only with the key on or during cranking as well? if you swapped them out directly then you should have no issues. somethings not plugged in somewhere.


- How would I know if the ECU is powering up?? I swapped ECU's with no change. Next time I go I can try and see if DM will connect I guess.
- I do get spark, but no fuel.
- The check engine light never comes on.
- The only time the pump gets voltage is if I use the plug near the distributor and jumper power directly to it.
- I am gonna try and swap the ignition module tomorrow since it has been sitting for a while. I saw some posts saying theirs went bad while being parked for extended periods.


Here are the plugs that I cannot find a home for:

IMG_1818.jpg

IMG_1822_circled.jpg


None of these are on the Sy harness as far as I can tell.
 

bg_bls

New member
Re: New harness in the Sy and now it won't start

My new engine harness I think was from a Sy because all the plugs went in no problem. The dash harness is the one giving me probs which is why I think it is from a Ty. :(
 

jwaller

Evil Genius/SyTy Guru
Re: New harness in the Sy and now it won't start

the pic you have with the item circled is the mirror connector. if you are not getting the serv eng light then the ecm is not powering up. check the fuses on the back of the alt and the power block on the firewall and the starter connection.
 

JSM

Active member
Re: New harness in the Sy and now it won't start

Yep, I agree with John. ECM is not getting power, which is why you don't have injectors, CEL, or fuel pump turning on.
 

JSM

Active member
Re: New harness in the Sy and now it won't start

91blazins10 said:
That looks like it is for the glove box light.

I know the light on the seat is for the ashtray, so that makes sense.
 

JSM

Active member
Re: New harness in the Sy and now it won't start

Good call, might be hatch release. Since he is installing in a sy I guess he will need to install the rear hatch option also now. :)
 

JSM

Active member
Re: New harness in the Sy and now it won't start

All my friends pick on me, so you just joined the list of people I call a friend.

I would feel odd if someone wasn't picking on me.
 

JSM

Active member
Re: New harness in the Sy and now it won't start

DaveP6999 said:
cool :tup:

I just deleted the comment anyway. You were correct. It IS the glovebox light. The color just doesn't show up in his pic very well.

Regards, Friend,
Dave

Marking my calendar now as first time Jeff has been right this year.... O wait last years calender went without marks also...
 

bg_bls

New member
Re: New harness in the Sy and now it won't start

jwaller said:
the pic you have with the item circled is the mirror connector. if you are not getting the serv eng light then the ecm is not powering up. check the fuses on the back of the alt and the power block on the firewall and the starter connection.

lol, but I have three connectors circled. Which one are you talking about?? The fuse on the alternator is fine and I know for sure the starter one should be ok cause that one was a bitch to get to. I will double check the power block today.


JS Manufacturing said:
I know the light on the seat is for the ashtray, so that makes sense.

hmmm, that one makes sense for the ashtray, but I am pretty sure I already have the glovebox light plugged in. So I will double check that.


DaveP6999 said:
Not sure about the color, now. But the plastic itself DOES look like the glove box light.

It appears you are mixing a Syclone engine harness with a Typhoon IP harness. You have to deal with those six wires that go to the rear of the truck. Also, it's a bitch, but you need to compare ALL the wires' 'position' in the bulkhead connector (C100) between the two harnesses. As you saw in the earlier thread, there are differences.

DaveP

Ok, this is where I am confused. I found those 6 wires along my frame rail and followed them up to the connector at the firewall. Those 6 wires are the same on both the old and new bulkhead connector. Unless they go some where different after they leave that connector and go inside the truck?? It sounds to me like you are saying there should be another connector inside that cab that would run to the Ty fuel pump/rear lights and I am all out of extra connectors.... I will double check all the connections at the bulkhead connection today and see what I find.


Thanks again for all the help!!! :tup:
 

bg_bls

New member
Re: New harness in the Sy and now it won't start

Just found this in another post for a Ty:

C100.jpg


Now I am starting to understand my prob. Does anyone have a pic for the Sy for me to compare to??
 

bg_bls

New member
Re: New harness in the Sy and now it won't start

DaveP6999 said:
The upper one is a white wire, yes? If so, connect it to the white wire in the 'red' connector below it. the tan wire is the key buzzer. Not important right now.
Not sure on white wire...unfortunately I don't have internet access where my truck is at. I will look and report back.

OK, there are TWO black plastic connecters in this location. Both have 1 blk, and 1 org wire. One is for the glove box light, the other is for the stock CD / Stereo.
sounds easy enough

Pull the fuse box off the inside of the firewall. Look at the color of the wires going to this upper 6-pin connector from INSIDE the truck. I'll bet you only see three, and they're pnk, brn, and orn. These are for the ELC on a Ty.
The upper connector on the inside has all six wires and they match the wire colors on the engine side.

Now, look to the inboard side of the fuse box. There is a long, skinny connector on the side of it, yes? You never found a matching plug for this in your Sy, yes?
This plug I don't remember seeing. I will get some more pics for you to look at.

Six of these wires, need to be put into the 6-pin on the firewall. The remainder, two blacks (seat belt buckle switch) and the orn & wht (dome light) go to the wires coming up from under the carpet that go to these items in a Sy.
ok this makes sense. I have a black/white wire going under the carpet which used to plug into a connector with 2 black wires on my Sy harness. The Ty one does not have it.

If you need a pic of this connectior, I can do it. just ask.
I would REALLY appreciate any pics you could give me. I just don't recall seeing another plug near the fuse block that was not plugged in.

Now JS and I are 'even'. We both got one right...

DaveP

I will be heading back to the shop in a few hours to work on it some more. Would any of those wires cause the ECU to not power up? Or is that another problem somewhere else?

EDIT: Damn, sorry about the red font. I thought it would stand out a little more.....guess not.
 

bg_bls

New member
Re: New harness in the Sy and now it won't start

DaveP6999 said:
I don't have this diagram for a Sy. But, I did compare the Sy and Ty C100 in the helms manual. They're identical, with the exception of the "6-pin" we've discussed previously. None of this has to do with "no check engine light".

Do the headlights work? If yes= fusible links @ alternator are OK.
Double check ECM A & B fuses.
Did you connect the white 12-pin at the ECM ? (C212) (Between the engine and IP harnesses.)


To Sumarize:

Fix the 6-pin to rear of truck.
Double check ECM fuses.
Looks like you're OK @ C100 to engine harness.
Post with anything else that doesn't work, or make sense, or you can't find a 'matching' connector for. There souldn't be ANY 'blanks'.

DaveP

Yep headlights work.
Both fuses are fine.
I will double check the white 12 pin. I am pretty sure it is in.
I will get my buddy to come take some more pics of what I can't match up.
Which Helm's manual do you have?? I got a crappy one at the local Auto Parts store which doesn't really have much for a Sy/Ty in it.

BTW. You rock!!! :thumbsup: I would have never figured this out by myself.
 

bg_bls

New member
Re: New harness in the Sy and now it won't start

Ok. I guess that is possible. I picked up both the harnesses from Ray Moore. It is good to have a Sy parts man like 45 minutes away. :lol:

I am positive I do not have that connector on the side of the fuse box.

Whereabouts is that white connector gonna be?


EDIT: Just reread. The white connector is at ECU. I'll check it out.
 
Top