So who on the board is doing powder coating...

sharkbait

New member
in NY NJ? i did a search and came up with a bunch of people who have bought the eastwood kit. i'd love to use a local member (obviously pay them).

I've decided to powder coat my acc brackets, pulleys, throttle bracket, thermostat housing, upper/lower intake, exhaust manifolds/crossover.
 

Syclone #1721

I LOVE 4UM SUPERSTARS
Re: So who on the board is doing powder coating...

I powder coat. I can do all those pieces in wide assortment of colors. I would not recommend the powder on the manifolds and crossover. I have used high heat powders that were supposed to be good to 1200 degrees just to have them flake off later. I would recommend ceramic coatings for them but the other pieces I can do no problem.
 

James Thomas

"NO CLASS"
Re: So who on the board is doing powder coating...

Syclone #1721 said:
I powder coat. I can do all those pieces in wide assortment of colors. I would not recommend the powder on the manifolds and crossover. I have used high heat powders that were supposed to be good to 1200 degrees just to have them flake off later. I would recommend ceramic coatings for them but the other pieces I can do no problem.


I have to agee, I have used (and seen others use) the Eastwood and other brands of Hi Temp powders and they aren't all that and a bag of chips too, so to speak. Preperation of the parts is about 99% of the job but I'm still not happy with the long term life of the powder for ultra hi temp applications. By the way Eastwood gets it's powders from several different manufactures, some better than others. Dupont is a good supplier as are several others but they use different manufactures based on price. Even with proper prep, I have seen and personaly had the powder flake and burn.

I think turbo use is just too hot for the current powder's available on the maket at this time but they do continue to get better every year. I would go ceramic on the exhaust as well :2cents:

_________
James
 

Ross L

Member
Re: So who on the board is doing powder coating...

I've had good results on NA exhausts using hi temp powder. 1) sand blast, 2) clean with acetone 3) powder and cure. Any other time I've varied from this,,,, failure. The black ceramic(liquid) is pretty easy to apply(no buffing), can be air cured and has the highest temp rating. :2cents:
Ross
 
Last edited:

warmpancakes

New member
Re: So who on the board is doing powder coating...

My powdercoater would not do my manifolds or downpipe in silver, he said black only as the silver would not survive
 

James Thomas

"NO CLASS"
Re: So who on the board is doing powder coating...

The Hi Temp powder works fine on 99% of most street builds if preped correctly (as mentoined above). He's asking about our turbo applications I.E. the crossover and DP though. The black will last longer but it still will not be as good / last like ceramic for turbo use. Again, just IMO. I have done it and it looked good until your start pushing it / tuning or throw NOS to it, then it started to show it's "limits for HI HEAT", the silver is not near as good.

___________
James
 

Ross L

Member
Re: So who on the board is doing powder coating...

Anyone here should be able to apply the black ceramic coating( providing you have an airbrush gun and compressor). The most difficult part is prepping :( and its good to a claimed 2000 deg. Back to powder. It's most durable when your trying to get it off :rant: Then nothing(torch,baking @ 600+ deg, sandblasting) will get it off :rotf:
 

Syclone #1721

I LOVE 4UM SUPERSTARS
Re: So who on the board is doing powder coating...

Every time i do high heat, my prep is as follows. Clean all parts with solvent. Then clean with brake cleaner and blow dry. Bake @ 450 for 45 minutes. Remove and clean with brake clean again. Glass bead. Brake clean one more time and blow dry with compressed air. Pre heat for 15 minutes @ 450. Apply powder. Allow to gel for 5 minutes @ 450 and then cure for 30 minutes @ 400. It doesnt get any better than this. STill it flakes off. I have tried 3 different brands with no luck.....CERAMIC THE HIGH HEAT EXHAUST PARTS! Trust me.
 

sharkbait

New member
Re: So who on the board is doing powder coating...

yeah. i agree regarding the the manifold/crossover. i spoke to a few people off of syty and they said the same. its just too much heat for the powder coating to handle.
 

Ross L

Member
Re: So who on the board is doing powder coating...

not trying to get off topic but,,, the high temp powder I use calls for "sandblasting"( to clean and etch the surface). Then clean with acetone and apply. The only time I had powder coat flake was when I cleaned with "greased lightning" after sandblasting. Now it's only sandblast,acetone,powder and bake. Never flaked since. But still, not good for a turbo application. It will eventually turn dark and burn off. :2cents: Again, the black ceramic spray on coating is easy and works!
Ross
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
Re: So who on the board is doing powder coating...

mine said the same black only on high heat items

warmpancakes said:
My powdercoater would not do my manifolds or downpipe in silver, he said black only as the silver would not survive
 

sharkbait

New member
Re: So who on the board is doing powder coating...

im def gonna do a all matte black finish. from top to bottom. intake and all. the only color will be braided AN fittings, aluminum water pump/ radiator /overflow canister/ intake piping A2A and a fluid damper.

i will prob go with a ceramic coating for the manifolds/crossover. i was thinking about a header wrap, but i know they trap condensation and make headers rust very quickly. im not sure about stock cast iron manifolds. its something to consider.
 

mattw

Active member
Re: So who on the board is doing powder coating...

Syclone #1721 said:
Every time i do high heat, my prep is as follows. Clean all parts with solvent. Then clean with brake cleaner and blow dry. Bake @ 450 for 45 minutes. Remove and clean with brake clean again. Glass bead. Brake clean one more time and blow dry with compressed air. Pre heat for 15 minutes @ 450. Apply powder. Allow to gel for 5 minutes @ 450 and then cure for 30 minutes @ 400. It doesnt get any better than this. STill it flakes off. I have tried 3 different brands with no luck.....CERAMIC THE HIGH HEAT EXHAUST PARTS! Trust me.


Why do so many of you guys prefer glass bead over sand? I've heard it doesn't pit the metal as much as sand but personally I like the pitting and I think it makes your primer/powder/whatever hold a hell of a lot better.


-Matt
 

Syclone #1721

I LOVE 4UM SUPERSTARS
Re: So who on the board is doing powder coating...

mattw said:
Why do so many of you guys prefer glass bead over sand? I've heard it doesn't pit the metal as much as sand but personally I like the pitting and I think it makes your primer/powder/whatever hold a hell of a lot better.


-Matt

Glasss bead cuts better and finer than sand. Hands down, the prefered all purpose media for numerous metals and alloys.
 

Ross L

Member
Re: So who on the board is doing powder coating...

I use Techline brand(ceramics). It actually states in large letters "DO NOT GLASSBEAD" it apparently doesn't etch the surface enough for a good adhesion. There's TONS of good info over on Caswell's powder coating forum caswellplating.com (i think). Good luck!
Ross
 

MikeRenz

not stock
Re: So who on the board is doing powder coating...

there is an industrial powdercoating facility pretty local to me that i use. their prepwork alone is worth the price of the coating. powdercoat is like paint...its only as good as what you do beforehand. i can have all your stuff coated if you like (plus thy have over 300 powders on hand)

UpperPC1.jpg
 

Syclone #1721

I LOVE 4UM SUPERSTARS
Re: So who on the board is doing powder coating...

Heres a pic of a bike riser I just did last night in 80% gloss. The little specs are cotton specs from the cloth I was handling it with.
DSCN0158.jpg
 
Top