Whats holding my boost back?

TYTILIDIE

METH HEAD
I think I posted about this a few months ago but its happening again. For some reason, I turn the EBC up and I can only get 18psi out of it. Now I have run 19 and 20 successfully before but it just wont do it now. Odd thing about this is, the other night, I had launched on this guy in a Lexus, and when I got through the intersection, it shot straight up to about 24psi. I turned the controller down. Well, I made another post about my truck and came to the conclusion more boost is needed here. So today I screwed around with it a little and the more I turned it up the more it just wouldn't respond, just wouldn't go over 18. I checked the actuator with a VAC pump and it seemed to be just fine. Then I checked the puck and it moves freely. So that pretty much leaves the controller or the solenoid, any ideas on how to test these? Could this be causing my problem somehow? I can do another VAC pump test, I may have done it wrong. What I did was applied vacuum and watched the rod move out, thats about all there is to it right?
 

It's just a six

Super Member
Re: Whats holding my boost back?

Your wastegate actuator does not work off of vacuum,it works with pressure ,psi.
When you are floored you do not have any vacuum,only pressure.
 

Windedv6

Ty n 10s
Re: Whats holding my boost back?

Check for leaks in your piping. I had that happen once and at a certain boost level it just flattened out. I was leaking around the clamps. Check them all and double clamp if nessessary.

I also had a cobra elbow suck in and close down enough to slow the boost. It would only do it after it got hot. I would make a run and everyhting was fine, then on the second or third boost it would fall on it's face because the rubber got hot and collapsed. It took me weeks to figure it out. I finally took of the filter and elbow to see if the turbo wheel was hitting or draging. I left the filter and elbow off for some testing and the boost was perfect!! . As soon as I put the elbow back on it acted up again. Go figure... I had to reinforce it.

John
 

TYTILIDIE

METH HEAD
Re: Whats holding my boost back?

It's just a six said:
Your wastegate actuator does not work off of vacuum,it works with pressure ,psi.
When you are floored you do not have any vacuum,only pressure.

Good point. Can't believe I didn't think of it that way.
 

TYTILIDIE

METH HEAD
Re: Whats holding my boost back?

Windedv6 said:
Check for leaks in your piping. I had that happen once and at a certain boost level it just flattened out. I was leaking around the clamps. Check them all and double clamp if nessessary.

I also had a cobra elbow suck in and close down enough to slow the boost. It would only do it after it got hot. I would make a run and everyhting was fine, then on the second or third boost it would fall on it's face because the rubber got hot and collapsed. It took me weeks to figure it out. I finally took of the filter and elbow to see if the turbo wheel was hitting or draging. I left the filter and elbow off for some testing and the boost was perfect!! . As soon as I put the elbow back on it acted up again. Go figure... I had to reinforce it.

John

Ill do a leak test today. I run the stock orange elbow and don't THINK that would happen but I can look in to that as well.
 

TYTILIDIE

METH HEAD
Re: Whats holding my boost back?

Well, Ive tried just about everything. Had the actuator checked by a local turbo shop and they said it was fine. All vacuum lines look great. I even went as far as to hooking the stock solenoid back up and tuning it and that still didn't get me anywhere. I know this thing can hit 25 psi, Ive seen it do it more than once. I just don't know what else it could be. No cracks inside the wg area, puck moves freely. Could the actuator be sticking but not show up in a test somehow?
 

ghettosled

SYTY SUPERSTORE
Re: Whats holding my boost back?

pull the vacuum line to the wastegate off. if it does not make the high boost you are looking for you have a leak, or a mechanical problem.
 

supersports10

New member
Re: Whats holding my boost back?

ghettosled said:
pull the vacuum line to the wastegate off. if it does not make the high boost you are looking for you have a leak, or a mechanical problem.

x2 it should spike VERY HIGH THIS WAY, be carefull.
 

TYTILIDIE

METH HEAD
Re: Whats holding my boost back?

Damn, I forgot to do the waste gate thing but, on a somewhat lighter note, I did a leak test again and heard a hissing coming form the BOV. I took it off and it was seized. So like a true genius, I start trying to tap the piston out with a socket and a hammer. I cleaned it all up and put it back together and did another leak test. Results were awful, I banged up the ridge the piston sits on :shoot: This made it leak waaaay worse than it did. I felt like such a jackass. Im not sure if that would have cause my problem but the new bov should be here tomorrow so we'll see. I hope that was it. I will also unplug the WG tomorrow and see what happens.
 

ghettosled

SYTY SUPERSTORE
Re: Whats holding my boost back?

it usually helps when you provide all the information.. :) What type of BOV are you running?
 

TYTILIDIE

METH HEAD
Re: Whats holding my boost back?

Turbo XS RFL. What did I leave out, the brand or that it had a leak? I found the leak after all the posts. But yeah it was a very faint hiss. I also forgot to add that I found a slightly leaking hose clamp. You couldn't hear it hissing but bubbles showed when windex was applied, it was around the turbo outlet. I got a smaller clamp on there and it went away but it didn't make any difference.
 
Top