Sy/Ty Forum Opinion on this Truck Please

R&C_RallySyTy

Little Big Man
So, as you all know I have been looking for a Sy for quite some time. The current one I'm looking at needs a little bit of care. When I say a little bit of care I mean the following:

1. Headliner is falling down.
2. One of the fenders needs painted because a deer hit it. Did not cuase much damage but a new peice was installed. (the fender ground effect)

I want to list all of the modifications because there is alot. I don't know much about the motors and tranny and whats good and whats not. I can pick this truck up for under 13k. The motor has about 15-20k on it and the body itself has over 100k. Its in decent shape.

Jack Merkel Performance Engines Built the Motor

Race Prepped Short Block:
Block bored on precison stand & 2 step torque plate honed
Speed Pro "Plasma" moly piston rings; file fit
Diamond Custom 2618 Forged Custom Pistons
Eagle H beam connecting rods
Federal Mogul Super Duty Alloy Main and Rod Bearings
Federal Mogul cam bearings
Speed Pro double roller timing set
Comp Cams custom grind Xtreme Energy hydaulic roller camshaft
Comp Cams Magnum hydaulic roller lifters
Comp Cams valve springs
Pro Gram Engineering splayed bolt, 4 bolt center caps, convert to 4 bolt main bearing splayed bolt block
ARP coonecting rod bolts, main studs
Degree in cam
Hot Tank block, heads, misc., install new core plugs
Precison ground crankshaft, nitrate treated
Balancing rotating assembly
Align bore main saddles
HD oil pump w/HD driveshaft
Engine Gasket set (includes "GM" head and intake gaskets specific to the Syclone/Typhoon)

Heads and Valve Train:
Competition valve job on original cylinder heads
HD vavle springs matched to camshaft
Comp Cams Magnum Roller tip rocker arm kit, 1.6:1 ratio
ARP head studs
Cylinder head resurfaced
Engine Professionally assembled

Later this was changed to Brodix heads from what I understand because the mech. said you won't get much out of that.

Looks like on the receit the following was added as options:
Brodix cylinder heads (Manley pushrod guide plates and screw in studs)
Bowl and Chamber port work
Full competition port work

Transmission Rebuild
Rebuild Custom Supplied 700R4
Syclone/Typhoon to Street and Strip
Specs for use with lock-up Torq Converter

Persicion Industires 9.5 L/U Torq Converter
Hi-Pro trans Upgrade
Includes billet servos, wide band, beast sunshell? Racing 3-4 Clutch pack, servo CK vavle?
5 pinion planets Front and Rear

Rebuild Transfer Case
Includes new front career, input shaft, planet and chain
Corvette Governor (5200 rpm shift)

Other Stuff
Set of 50lb Fuel injectors
3 bar map sensor
O2 sensor 3wire
wastegate kit
2end Alky nozzle kit
plugs 3 sets
Exhaust band clamp
EGR block off plate
FAST fuel injection mangement system
fuel injection wire harness
EST Spark Module
Engine Mounts

Upgraded Turbo and Other Stuff
TE45A
66 intake wheel
.63 Prescion exhaust
Hi Torq Starter
3" Custom Built Stainless headers
3" Race gate Downpipe
Turbonetics Racegate wastegate

The truck also comes with 2 sets of brand new tires. Not sure what one set it but the other is 4 BFG Drag Radials DOT.

Seems like a well built truck, anything I should look out for when he takes me for a ride. I'm looking for everyones opinion because to me it seems like its my dream truck. Do some cosmetics, nice set of vette wheels and paint the fender, get a new headliner and I should have a mean truck. Thanks guys.
 

bezerk

New member
Re: Sy/Ty Forum Opinion on this Truck Please

don't be fooled by that list of parts thrown in.
it seems like a nice list, but than again. 13K is not cheap.
heck you can buy a truck that needs a paintjob and an engine for $4K and spent 9k on a new engine. tranny and a paintjob and know everything is new.
some pics will help. and what's the mileage of the truck?
 

Ry368

one mile = 5280 feet
Re: Sy/Ty Forum Opinion on this Truck Please

If you can clean the body up yourself(if needed) I'd say do it!!!! The heads and fast system are worth over 5k new and all the other parts sound really nice!!! Just make sure there are no wiring bugs or boost issues.

Have you drivin this truck around a little bit yet.....if so how did it feel?
 

warmpancakes

New member
Re: Sy/Ty Forum Opinion on this Truck Please

If jack merkel is Todds dad i wouldnt worry about the motor todd knows his shit and built some bad ass cars
 

R&C_RallySyTy

Little Big Man
Re: Sy/Ty Forum Opinion on this Truck Please

bezerk said:
don't be fooled by that list of parts thrown in.
it seems like a nice list, but than again. 13K is not cheap.
heck you can buy a truck that needs a paintjob and an engine for $4K and spent 9k on a new engine. tranny and a paintjob and know everything is new.
some pics will help. and what's the mileage of the truck?

The engine has about 15k and the truck itself has a little over 100k.
 

R&C_RallySyTy

Little Big Man
Re: Sy/Ty Forum Opinion on this Truck Please

Ry368 said:
If you can clean the body up yourself(if needed) I'd say do it!!!! The heads and fast system are worth over 5k new and all the other parts sound really nice!!! Just make sure there are no wiring bugs or boost issues.

Have you drivin this truck around a little bit yet.....if so how did it feel?

I can do all that work myself. As far as I know it was running 11s 1/4th mile and was only run a few times. The guy is retiring and doesn't need the truck anymore. Guess he wants some cash to go on a vaction or something.
 

R&C_RallySyTy

Little Big Man
Re: Sy/Ty Forum Opinion on this Truck Please

Ry368 said:
If you can clean the body up yourself(if needed) I'd say do it!!!! The heads and fast system are worth over 5k new and all the other parts sound really nice!!! Just make sure there are no wiring bugs or boost issues.

Have you drivin this truck around a little bit yet.....if so how did it feel?

I'm going to drive it and take it out this weekend. Anyways I hope to. Maybe even tomor.
 

bezerk

New member
Re: Sy/Ty Forum Opinion on this Truck Please

R&C_RallyTy said:
I can do all that work myself. As far as I know it was running 11s 1/4th mile and was only run a few times. The guy is retiring and doesn't need the truck anymore. Guess he wants some cash to go on a vaction or something.

i would say it depends on a whole lot of things, if a truck like that would have shown up at ebay. and nobody knows the truck and it runs 13.x everybody would say they slapped a kennebell cata. at it.
if it's a solid truck that runs great. and the owner knows his stuff it''s a nice deal.

goood luck
 

dgoodhue

BuSTeD 4.3
Re: Sy/Ty Forum Opinion on this Truck Please

The truck should fly with that combo, well into the 11's is what I would expect. If that is what your looking for it might be the truck for you.
 

Flyin Ryan

hated cuz he drives fords
Re: Sy/Ty Forum Opinion on this Truck Please

great list of parts... i'd take it for a test drive and do a compression check on it.. If everything checks out i'd say that's a deal.
 

FxsX24

94 S10 to be lowered/v8
Re: Sy/Ty Forum Opinion on this Truck Please

we may have a better opinion with the last 4 of the vin
 

R&C_RallySyTy

Little Big Man
Re: Sy/Ty Forum Opinion on this Truck Please

FxsX24 said:
we may have a better opinion with the last 4 of the vin

What does the last 4 have to do with your opinion? Is there something you can find out about the last 4 other then which production Sy is was?
 

Flyin Ryan

hated cuz he drives fords
Re: Sy/Ty Forum Opinion on this Truck Please

R&C_RallyTy said:
What does the last 4 have to do with your opinion? Is there something you can find out about the last 4 other then which production Sy is was?


since this community is super small and tight people tend to know trucks by there vin and remember who owned them and what kind of history they have being it good or bad so most of the time when someone post a question about looking at a truck and post the vin or the truck number (last for digits of the vin) most people can chime in with there take on the previous owner's antics or what kind of shape that truck's been in over the years, how many times it's changed hands etc.
 

R&C_RallySyTy

Little Big Man
Re: Sy/Ty Forum Opinion on this Truck Please

Flyin Ryan said:
since this community is super small and tight people tend to know trucks by there vin and remember who owned them and what kind of history they have being it good or bad so most of the time when someone post a question about looking at a truck and post the vin or the truck number (last for digits of the vin) most people can chime in with there take on the previous owner's antics or what kind of shape that truck's been in over the years, how many times it's changed hands etc.

Interesting, maybe I'll have to go take a look at these papers and post the last 4. With as many scams out there it would be a good idea to have a way other then proof of receits that the work was done to this truck. You can't be to careful now adays. With that mod list I gave, how would I know the internals were really there? Also I'm going to buy a compression tester and check that out. Does anyone know what kind of compression I should be looking for with the following mods that I posted? Thanks again for all your help. I hope to be part of this fine and select group here.
 

turboj91

New member
Re: Sy/Ty Forum Opinion on this Truck Please

You will not be able to determine exactly what compression numbers you should be looking for unless you know exactly which camshaft is installed. To be very specific on what the numbers should be, you would also need to know the chamber size, deck height and head gasket thickness. Without this information your best bet would be to check that all the cylinders are within a certain percentage of each other (10%). Considering what it takes to change all the plugs on these trucks, don't be suprised if the seller is not that enthusiastic about the process. I would lean more toward driving it for a bit and obtaining as much info as possible from Data Master. Seat of the pants feel does not hurt either.
 

R&C_RallySyTy

Little Big Man
Re: Sy/Ty Forum Opinion on this Truck Please

turboj91 said:
You will not be able to determine exactly what compression numbers you should be looking for unless you know exactly which camshaft is installed. To be very specific on what the numbers should be, you would also need to know the chamber size, deck height and head gasket thickness. Without this information your best bet would be to check that all the cylinders are within a certain percentage of each other (10%). Considering what it takes to change all the plugs on these trucks, don't be suprised if the seller is not that enthusiastic about the process. I would lean more toward driving it for a bit and obtaining as much info as possible from Data Master. Seat of the pants feel does not hurt either.

Yea, I was thinking the same thing. It will be very diffacult to find out everything exactly 100%. I do have the performance shop #. I'll give them a call and see what kind of info they can give me on the motor and the compression ratio. They should know all of those things. The weekend is getting closer and with each day passing I grow more and more joyful with anticipation! :)
 

Tooky

Serious about performance
Re: Sy/Ty Forum Opinion on this Truck Please

Not to be a stick in the mud, but you did ask for opinions. How much turbo tuning/modding experience do you have? You said you didn't know much about the engines or trannys. It seems to be awfully rare that anyone sells a good running, well-maintained modified SyTy that runs like it should. The last one I can remember is Denny Raab's "sycho". A lot of times what happens is guys have a race engine built, throw a ton of parts at it, and it never runs right and becomes a big frustration so they ultimately unload it. I have seen it so many times.

Not saying this is the case with this truck but warning you to be cautious and maybe check things out with the owner. A modded truck like this is going to require a lot of expert TLC to keep running even IF it's in 100% tuned shape to begin with. It's nothing like buying a new (or even used) LS1 V8 muscle car that you can beat the crap out of and it will always run the same. The fact that the headliner is falling and the panels didn't get painted after the deer accident tells me the owner perhaps didn't have a ton of pride in his truck... What else couldn't he "be bothered to fix"....??

Just some things to consider IMO.
 

R&C_RallySyTy

Little Big Man
Re: Sy/Ty Forum Opinion on this Truck Please

Tooky said:
Not to be a stick in the mud, but you did ask for opinions. How much turbo tuning/modding experience do you have? You said you didn't know much about the engines or trannys. It seems to be awfully rare that anyone sells a good running, well-maintained modified SyTy that runs like it should. The last one I can remember is Denny Raab's "sycho". A lot of times what happens is guys have a race engine built, throw a ton of parts at it, and it never runs right and becomes a big frustration so they ultimately unload it. I have seen it so many times.

Not saying this is the case with this truck but warning you to be cautious and maybe check things out with the owner. A modded truck like this is going to require a lot of expert TLC to keep running even IF it's in 100% tuned shape to begin with. It's nothing like buying a new (or even used) LS1 V8 muscle car that you can beat the crap out of and it will always run the same. The fact that the headliner is falling and the panels didn't get painted after the deer accident tells me the owner perhaps didn't have a ton of pride in his truck... What else couldn't he "be bothered to fix"....??

Just some things to consider IMO.

I agree 100% and I respect your post. As for the truck, I just got back from my road trip. The verdict is in: As for the headliner it was not as bad as he said. It just has a few very small like bubbles. Its hard to explain. Anyways, it is in pretty good shape. Started right up, no smoke. It idled fine and seemed pretty good. We pulled the plugs, here is where the fun part begins. Like I said I know basic stuff, so I brought a friend. The plugs were burning very good but I noticed a little bit of oil or maybe fuel on the threads. This is not a good sign and since it was not dyno tuned I don't know what to think. It could be the rings going bad.

It does need a little TLC. We took it out for a drive and then something happened. It felt like it had alot of power but I was not behind the wheel. We get back and he tells me he won't let me drive it. He was very honest and looked distrubed. He told me the truck is not running right and he is surprised because last time he had it out it ran great. He told me not to buy it until he figures it out. At least hes a honest guy, I don't know what to think. That thing seemed to spool quick though and the tranny shifted very hard and clean. I'm very disapointed in todays trip. What do you all think about that?

So, could it of flooded and just not of been running right because of that. Is it because it was not dyno tuned, or could the rings be bad. It did seem to have good oil pressure, fuel pressure ect. If it is just rings going bad, that still does not explain why it was not running 100%. He said he knows the truck very well and its just not right today.
 
Top