Help: Engine doesn't want to be alive

Andrew

New member
Hi everybody! First of all I ask you excuse for my english. I'll try to explane my problem. Engine and stock turbocharger of my Typhoon'92 been remanufactured, but doesn't work yet. It started normally, but after 5 psi pressure, exhaust is shooting, injectors flow too many fuel and engine is - off. I've changed a few chip's programs with different injector's flow rating, the result is the same. Maybe somebody had a trouble like this or can to explane what I need to do? Please advise!!!

Sinerely yours Andrew from Moscow.

P.S. Is the turbocharger disconnected, exhaust is not shooting and engine work normally, but of course with no power. When engine is cold, exhaust is shooting after 9-10 psi.
 
Last edited:

Tooky

Serious about performance
Re: Help: Engine doesn't want to be alive

Do you have a Wideband (Lambda) O2 sensor to tell you how Rich or Lean the fuel mixture is in the exhaust??

What are you using to tune? Do you have a stock ECM? Our stock ECM doesn't really have a injector constant that can be changed (not sure if thats what you were changing). Do you have stock Red-top 28# fuel injectors?

If you have a chip burner or chip emulator you can try downloading various 3-Bar chip tunes from my website but you of course will need a 3 Bar MAP Sensor to match these chips if you run them..

PS: Your english is pretty good. :)
 

Andrew

New member
Re: Help: Engine doesn't want to be alive

Thanks for answer Tooky!
Your questions answers:
1. Yes, I've connected wideband.
2. I'am using to tune TunerPro software.
3. I've stock ECM. Only tryed to reprogramm chip.
4. I've #36 Delphi injectors.
5. I've used 2-bar MAP sensor.

When I've reprogramed chip, I changed injectors flow ratio (in Tuner Pro), but result was the same - exhaust is shooting. I've bought Ostrich 2.0, but Tuner Pro doesn't want to see this device.
I'am trying to understand, is it problem in ECM (chip) or something other? Maybe there is a malfunction in eigine, in wires, in sensors, in Vortec heads, in.........? What I need to buy? I'am ready for everything, I'am very tied with this car.
 

Tooky

Serious about performance
Re: Help: Engine doesn't want to be alive

The injector flow ratio is not used in our application. I bet you can change it to an absurd value like "80# injectors" and it won't run any different. I'm not sure why it even shows up in TunerPro.

If you have a stock chip, 2 bar MAP, but 36# injectors, the injectors are bigger than what the chip is programmed for (28# stock) and could be causing your rich problem.

You could try the F28 "Base Pulse Constant vs. Desired EGR" table. This is a lot more like the REAL injector constant (even though it talks about EGR, just ignore that.) Try multiplying the whole table by 0.9 and see how it runs. That should remove "10% Fuel" everywhere. You must be careful of course, one wrong click and it could go too lean and cause damage. I suspect you knew that though. ;)

Edit: I re-read your posts. Wow, thats a really odd combination. 36# injectors, 2 bar Map sensor, stock chip(?), stock turbo, Vortec heads? You're going to really have your hands full since this is so different than a stock truck! And I agree - it will be tough trying to determine , Is it the ECM, is it the injectors, is it the heads, etc... All I can say is "Good Luck" and go slowly.. be careful.... and read my website www.PowerTunePlus.com :D :tup:
 

Andrew

New member
Re: Help: Engine doesn't want to be alive

What do you mean when say application? Is it software or chip? You absolutely right, I tryed to change like #80 value without any difference.
Please tell me, maybe it is better to buy a different chip? If it possible?
As I understood, I need to buy 3 bar map?
"F28 "Base Pulse Constant vs. Desired EGR" - I'll try.
You said - odd combination. What do you mean? What I need to change in this combination? Please advice.
You know Tooky, I've not quite a stock torbocharger. There is 20 compressor wheels installed, during rebuilding.
 
Last edited:

Andrew

New member
Re: Help: Engine doesn't want to be alive

Thanks for recomendations. Please tell me, do you know what is "BigStuff 3 EFI - Plug and Play" it? Can this device be a good solution of my troubles?
 

Tooky

Serious about performance
Re: Help: Engine doesn't want to be alive

Andrew said:
What do you mean when say application? Is it software or chip? You absolutely right, I tryed to change like #80 value without any difference.
Please tell me, maybe it is better to buy a different chip? If it possible?
As I understood, I need to buy 3 bar map?
"F28 "Base Pulse Constant vs. Desired EGR" - I'll try.
You said - odd combination. What do you mean? What I need to change in this combination? Please advice.
You know Tooky, I've not quite a stock torbocharger. There is 20 compressor wheels installed, during rebuilding.

What chip (or .BIN) are you starting to tune from? Your job will be easier if your combo matches the parts your chip was designed for.

I wrote a web page about the 4 main levels of modification and what parts match best:

http://www.powertuneplus.com/syclone/stages.shtm

Here's a graphic representation:

performance_roadmap_43tv6.png



However, I'm sure parts are hard to come by in Russia. I'm just pointing out that no matter what "chip" you run, you'll probably need to calibrate it for your unique setup.

You only need a 3 bar MAP if you plan to run a 3 bar BIN(chip). I have some on my website for free download.

Andrew said:
Thanks for recomendations. Please tell me, do you know what is "BigStuff 3 EFI - Plug and Play" it? Can this device be a good solution of my troubles?

Sure it will work, but so will the stock ECM if you tune it. Both devices require tuning and both are capable of running your truck smoothly when tuned.
 
Top