Getting Rid Of Rust...Doors,Fenders,etc.

Ok I'm looking to get rid of the small bit of rust on the truck...The normal stuff you find on a N/E S10...

I'm not going to mess around with restoring the parts...since Ive been told it always shows or finds a way to come back... So I'm looking into getting brand new fenders, and brand new door shells since the rust is on the front fenders (mainly the broken cladding side P/S) and under the doors (on the inside)

The rest that can be found is just barely surface rust that can be cured with some POR-15

So here's my questions... I found this seller on Ebay (carpartswholesale) Has anyone purchased new replacement fenders? (I'm assuming these are aftermarket) Do they fit well? Also If I buy the door shell and move over all the panels, wiring, glass, etc. Is a Sy/Ty door just a regular old s10 door with cladding on it? Or is there something I will have to modify on the door to get that cladding on and have it look like an OEM Sy/Ty door? (ie: shaving, planing, grinding, cutting, etc.)

Also, anyone have experience with POR-15? Would it be worth it to coat the front and back of the new parts with it before priming and painting? I'm looking to restore the truck's exterior and not have to do it again for a LOOOOONG time, since most of my time will spent in the engine bay or tuning and it would be rough to keep re-painting or rust treating the truck during that time...
 

T-Bone

Active member
Re: Getting Rid Of Rust...Doors,Fenders,etc.

Ok I'm looking to get rid of the small bit of rust on the truck...The normal stuff you find on a N/E S10...

I'm not going to mess around with restoring the parts...since Ive been told it always shows or finds a way to come back... So I'm looking into getting brand new fenders, and brand new door shells since the rust is on the front fenders (mainly the broken cladding side P/S) and under the doors (on the inside)

The rest that can be found is just barely surface rust that can be cured with some POR-15

So here's my questions... I found this seller on Ebay (carpartswholesale) Has anyone purchased new replacement fenders? (I'm assuming these are aftermarket) Do they fit well? Also If I buy the door shell and move over all the panels, wiring, glass, etc. Is a Sy/Ty door just a regular old s10 door with cladding on it? Or is there something I will have to modify on the door to get that cladding on?

Also, anyone have experience with POR-15? Would it be worth it to coat the front and back of the new parts with it before priming and painting? I'm looking to restore the truck's exterior and not have to do it again for a LOOOOONG time, since most of my time will spent in the engine bay or tuning and it would be rough to keep re-painting or rust treating the truck during that time...

I can tell you this....very few replacement body panels ever line up like an OEM panel. The doors are interchangable on S10's / Syclones but the guts might be different (standard S10's did not come with power features like a Sy and the cladding mount holes will be missing on a standard S10 door. If you go with a standard door, you better have a good eye to drill the holes for the cladding mounts (or make a template from your rusted door). Check on here. Someone may have a rust free SyTy door to sell you so you circumvent all the hassles doing it yourself.
 

warmpancakes

New member
Re: Getting Rid Of Rust...Doors,Fenders,etc.

all the body panels are standard s10 you just need to drill the cladding holes there is a template in the assy manual Personally I would use oem panels but be warned they arent cheap Fenders are 300 ish each and doors are 400-500 each
 

jhj

New member
Re: Getting Rid Of Rust...Doors,Fenders,etc.

Just had mine done, new doors, fenders, cowling and endgate(tailgate). The fenders and cowling were from LMC. The doors were from GMpartsdirect as was the endgate. My total was about $1400 incuding shipping. The body shop had trouble with the fenders but everything else went ok. You will find it hard to get some things but just keep looking and anything you recieve from shipping INSPECT it before you sing for it. Most of my parts had to be reshipped due to DAMAGE by the shipper. I now have a near rust free TY.
 

jhj

New member
Re: Getting Rid Of Rust...Doors,Fenders,etc.

Just had mine done, new doors, fenders, cowling and endgate(tailgate). The fenders and cowling were from LMC. The doors were from GMpartsdirect as was the endgate. My total was about $1400 incuding shipping. The body shop had trouble with the fenders but everything else went ok. You will find it hard to get some things but just keep looking and anything you recieve from shipping INSPECT it before you sing for it. Most of my parts had to be reshipped due to DAMAGE by the shipper. I now have a near rust free TY.

OH I have a endgate that is in good shape, small amount of rust, little dent, that I will sell if you are interested.
 
Re: Getting Rid Of Rust...Doors,Fenders,etc.

Ive used POR-15 many times and it can be good and can be bad. The base metal has to have a profile from like sand blasting if its SMOOTH the POR-15 will peel off Personnelly ive used it on drive line parts and its peels off i think a GOOD primer and paint works better if you take it down to bare metal. I perfer powercoating more than anything its Tuff..
 
Top