Truck Won't Start - Desperate Need Of Help

jharrison

New member
There's no way to sum this up in a couple of sentences, so i'll apologise now and thank those who read through to offer help.

I bought my Sy about 5 months ago in Denver, Colorado and brought it back to San Antonio, Texas. As you can imagine I had problems primarily due to the severe altitude change (mile high vs 700' above sea level). The original owner traded the truck to Carmax who put just about every generic part Autozone sold on it(cap, rotor, plug wires, etc.) For the most part the truck ran fine except for pinging when boost hits 11+psi. I have been slowly replacing all the crap parts with decent OEM or better aftermarket ones. The latest "improvement" I made was the installation of Performance Distributors complete ignition system(cap, rotor, plug wires, coil, and ignition module). Now the truck cranks but won't fire. I swapped the coil and module back to stock, no change. I checked the resistance to all plug wires and the coil wire, they are all lower resistance than stock as they should be, no problems here either. I pulled the plug wires on cylinders 1 & 3 and both have spark. I pulled the plug on cylinder 1 and it had a little gas on it, this and the fuel pressure gauge confirm fuel. Still cranks with no fire. In my panic I have replaced the whole distributor and pick-up coil, the oil pressure switch/sender, both the coolant sensor and sender, and all the relays on the firewall except the larger Bosch one. The service manuals diagnostics told me to ground the ALDL to check for code 12 which I did. The service engine light stays on constant and then code 12 is displayed. From here it tells me to check for an open or short on the serial line. That too is fine, so from here it says the ECM or the MEMCAL is bad. (As a note I also found that a Pit Bull chip is installed)

Has anyone gone through this, it makes no sense? How can I have spark and fuel and it not fire? No pop, no sputter, no backfire, just straight cranking. I don't know what all this truck has incase it matters. I know in addition to that in my sig it has what looks to be a Ken Bell FPR and an ATR Pitbull chip. I also installed NGK UR6IX plugs gapped @ .028, and they only have about 10 miles on them. I also have no idea if the fuel pump is stock or not, but engine wise everything else appears to be stock.

Any help will be greatly appreciated, im at my wits end, I know now what true frustration is! :rant:
 

ghettosled

SYTY SUPERSTORE
Re: Truck Won't Start - Desperate Need Of Help

if you have spark and fuel your distributor is probably out of phase. If you have access to a noid light you can watch the injectors actually fire thus confirming the ecm is doing its thing. However if the fuel pump is triggering, i would guess the ecm should be ok.

Seen as how all you did was some ignition stuff, i would say something with the distirbutor (bad mag pickup, or out of phase)
 

martygar8

syclone #1322
Re: Truck Won't Start - Desperate Need Of Help

i gap my plugs at 35 and now the sy running real good, a friend of mine told me to gap them at 28, and the truck run like crap, and sometimes not all the cylinders would fire, just my :2cents: good luck with your syclone, you gonna love it!!!!!!!!!!!!!!!!
 

martygar8

syclone #1322
Re: Truck Won't Start - Desperate Need Of Help

yes it sounds like your timing is off, i change the distributor on the syclone and had a little trouble setting it!!!! they are a pain in the butt, good luck.
 

Trapper

New member
Re: Truck Won't Start - Desperate Need Of Help

I would almost say a bad memcal i just replaced my Disy just last week and for the life of me I was going crazy because I thought I couldn't find TDC but I had a hunch to swap memcals and it started right up. I don't know waht that was about.
 

jharrison

New member
Re: Truck Won't Start - Desperate Need Of Help

I would almost say a bad memcal i just replaced my Disy just last week and for the life of me I was going crazy because I thought I couldn't find TDC but I had a hunch to swap memcals and it started right up. I don't know waht that was about.

The "Syclone Service Manual Supplements" diagnostics point to the MEMCAL or ECM. I just don't know how it could have just gone bad. Any ideas how / where to get a stock one, all I have is the Pitbull I bought it with. Are there any ways to confirm or rule out a faulty ECM or MEMCAL?

As far as timing goes, I haven't ruled it out, but this problem started before I swapped distributors. After the swap there was no change. I did the usual refrencing of the rotor position as well as the base orientation, then just dropped the new one in place exactly as the old one was.
 

Trapper

New member
Re: Truck Won't Start - Desperate Need Of Help

Marty glad to hear your up and running, but J I don't know why the memcal or ECM do this but see the original chip in my truck would go rich when you stepped on it with a load I was kept being told it was maybe the ignition so everything checked out good except the dis was original and old so I swapped it out since I replaced everything else so when I went to start it on the original chip it would not start, I finally after 4 days of trying every position on the disy to get it to fire I swap in the second chip and memcal and it fires right up, it still goes way lean but at least it fires and runs. I might have an extra memcal after I get this package that Fedex keeps losing or can't deliver for some dumb reason?
 

sly dvl

Ya, it's got a Turbo
Re: Truck Won't Start - Desperate Need Of Help

Have you tried un-seating and then re-seating your PROM / MEMCAL?
 

pinellas50

New Guy
Re: Truck Won't Start - Desperate Need Of Help

As far as timing goes, I haven't ruled it out, but this problem started before I swapped distributors. After the swap there was no change.

It didn't start once you messed with plug wires did it? If not, then timing probably isn't a factor.

I only mentioned that because I went through the very same scenario when I first got my truck. I pulled all the plug wires without marking them knowning I could read the firing order to put the new wires on correctly. But it turned out that the distributor was in 180 out when I got the truck and the last person to work on it just moved plug wires around to compensate. Obviously it wouldn't start or really do anything when I put the wires on correctly(which was 180 out because the distributor was previously dropped incorrectly).
 

jharrison

New member
Re: Truck Won't Start - Desperate Need Of Help

Have you tried un-seating and then re-seating your PROM / MEMCAL?
I did this and I also disconnected the battery overnight. Neither changed anything. I think you guys could be on to something with the wires being 180 out. I just pulled them and didn't pay attention where they were. On reinstallation, I just went with the diagram found here. http://www.whitetyphoon.com/firing_order.html I will move the wires 180 out and give it a shot.
 

Davemc1963

93 Ty Owner
Re: Truck Won't Start - Desperate Need Of Help

It didn't start once you messed with plug wires did it? If not, then timing probably isn't a factor.

I only mentioned that because I went through the very same scenario when I first got my truck. I pulled all the plug wires without marking them knowning I could read the firing order to put the new wires on correctly. But it turned out that the distributor was in 180 out when I got the truck and the last person to work on it just moved plug wires around to compensate. Obviously it wouldn't start or really do anything when I put the wires on correctly(which was 180 out because the distributor was previously dropped incorrectly).

Thats a good starting point. turn engine to TDC on firing stroke and check the alignment of the rotor arm to the No.1 distributor plug tower. You hopefully know that there are two timing marks on the damper. Make sure you use the correct one. (The second one if I remember in the normal direction of rotation. Someone may want to confirm this for me. I dont think you will be the first to use the wrong one) Have you tried to use a strobe, to see where it times when cranking? When I had a dissy problem, my plugs got so badly fouled with fuel, they wouldnt fire. With a strobe connected, I couldn't get a spark/flash! This sent me on a long wild goose chase, as the plugs were quite new, but because it wouldn't start, ended up sooty and fuel fouled. I only found this by using spare plug on an old plug wire to ground. The strobe flashed, but using the installed plug and wire, it wouldn't. Also the reseating of the memcal is also a good shout as well and making sure the ecm plugs are reseated as well. If the dissy/timing is in the ballpark with fuel & spark, it should fire/run if all else is well. Another thing to check is that the EGR valve if you have one is closed. If you pull the vacuumm line to it, it should close if its open. Then you can refit it.
 

Big Mike

New member
Re: Truck Won't Start - Desperate Need Of Help

I had a friend fry his ecm when the wires from the module on the dist grounded out to the base of the dist (his connectors were in very bad shape when this happened), see if you can get a loaner ecm to test.
 

jharrison

New member
Re: Truck Won't Start - Desperate Need Of Help

I guess at this point it has to be the ECM or MEMCAL, I moved all the plugwires out 180 and it backfired through the intake bad. It actually slightly warmed the intercooler.

Anyone know where I can purchase a stock MEMCAL, it looks like I can get the ECM for like 109 but they don't come with the chip. Does anyone know if I can check to see if either work using Datamaster software before I spend any more money?
 

Trapper

New member
Re: Truck Won't Start - Desperate Need Of Help

I should be getting an extra one tomorrow with some other stuff, I'm trying to get my things working with a different bin but I should have a spare this week.
 

Tooky

Serious about performance
Re: Truck Won't Start - Desperate Need Of Help

Try turning the ignition on but dont start the truck. Then connect datamaster and verify that all your readings look correct. Give it some throttle and verify the TPS follows and rests at 0%. That will at least prove your ECM is communicating properly and not in "limp home mode".
 
Top