Why would my boost be limited? Datamaster files included.

odium

1BADGMC
I have a few datamaster runs showcasing a boost limit problem. As you can see, I have it to where there is 0 spark retard and 0 knock, but the boost is stuck at a very steady 13.7-14 at WOT. Hey, at least it's steady, right? I used to get around 16-17 psi.

The only thing different is that I took my EGR out of the mix. I also replaced the vacuum lines around the turbo and boost solenoid, but I've replaced them about 12 times with other lines with these same results... Could this be the problem?

Just to let you know: I can boost launch at about the same limit, but no boost launches are in the datamaster files below.

Notice that the waste gate duty cycle is at 74.9 and doesn't change on boostlimit5. Is that where my problem is?

Would a crapped out MAP sensor do this? What are the symptoms of a bad map sensor or one that isn't getting the correct amount of vacuum/boost?

If my timing is too retarded (my balancer is slipped, so it is damned hard finding true 0), would that cause the boost to not crawl up to the full 16-17 it should be getting (ATR Pitbull)? I tried advancing it a little bit more, and the same boost limit was there. boostlimit5 is where it was advanced 1-2 extra degrees.

http://www.wsu.edu/~odiwik/boostlimit.uni
http://www.wsu.edu/~odiwik/boostlimit2.uni
http://www.wsu.edu/~odiwik/boostlimit3.uni
http://www.wsu.edu/~odiwik/boostlimit4.uni
http://www.wsu.edu/~odiwik/boostlimit5.uni

I have an aftermarket boost gauge, and both it and datamaster were reading 16-17 psi before. They both stop at 13-14 now for some reason...
 

93 TY 2185

Donating Member
I looked at your files. I don't see any "Boost Target" value in any of those files.
I don't know why this is, but it's something I noticed.
 

odium

1BADGMC
The cat doesn't smell like eggs. How do I check to make sure it isn't clogged? I've been dumping lots of fuel in the engine getting the thing tuned, so that might be a variable....

What are some other possibilities?
 

dgoodhue

BuSTeD 4.3
From what I understand, the ATR Pitbul doesn't have feedback for boost control (closed loop), it just opens the wastegate duty cycle for a certain throttle percentage (open loop) Did you adjust the wastegate at all?

FYI the pitbull wastegate table looks like this


TPS % 0 12.5 25 37.5 50 62.5 75 87.5 100
Wastgate 52.0 53.5 56.2 58.2 59.8 64.8 66.0 68.8 75.0

So 74.9 is right on for 100% TPS
 

odium

1BADGMC
I haven't touched the wastegate since I did vacuum lines, EGR delete, plugs, etc. etc... I checked the rod adjustment and it looked ok according to how kwick6 replies on all the arm adjustment posts (I searched it). I will check a third time tonight and make sure it's still right.

You're talking about the wastegate arm adjustment, right?
 

dgoodhue

BuSTeD 4.3
odiwik said:
I haven't touched the wastegate since I did vacuum lines,

You're talking about the wastegate arm adjustment, right?

Yeah I am talking about the wastegate arm adjustment.

If you had a slightly leak in the vauum lines in the boost control vacuum lines, then it would cause your boost be higher. If that is true be thankful you did you vacuum lines, because a big vacuum leak in those lines will cause you to loose boost control. This mean your boost will go as high was the turbo will produce, motor blows or until you back out of the gas from the horrible sounding noises.
 

odium

1BADGMC
Previous datamaster files showed that I would be at a constant 16-17 psi just as constant as the datamaster files above (straight line, looked good) and never spiked.

Am I supposed to be getting near 16-17 psi with the ATR Pitbull?

I was getting knock before I got rid of my EGR and redid these vacuum lines... I would let my foot off because of the "horrible sounding noises" and spark retard you mentioned, heh.

Would the vacuum leak cause a constant higher boost level, or would it spike to the high levels and go back down randomly?
 

dgoodhue

BuSTeD 4.3
odiwik said:
Previous datamaster files showed that I would be at a constant 16-17 psi just as constant as the datamaster files above (straight line, looked good) and never spiked.

Am I supposed to be getting near 16-17 psi with the ATR Pitbull?

The Pitbull is a 2 bar chip, it can only read to 14.5 psi. Your map sensor can only read to 14.5psi, I really don't see how datamaster was seeing 16-17 psi. Anything over 14.5 psi in the ECM read 15.0 psi (when you have a 2 bar map sensor). The reason ATR uses an open loop boost control is that it allows you to adjust you wastegate arm to the desired boost level.

I tried out an ATR on my stock Ty and I saw around 14 psi of boost.
 

odium

1BADGMC
Just an update: She runs like an f'n raped gorilla now. I'm going to write a book as a reply here, so if anybody has these problems they can see what I did to solve them.

I just spent the last three hours tuning it to run ~ 15.5-16 psi and it only gets .5 knock retard on the 2-3 shift consistently. I'm so happy I finally got her running right... I can finally start modifying some stuff.

Alright, the important part: How was it done and fixed?

Get datamaster and a laptop somehow. You can buy it or borrow it. You will need it. This is a must. All spark retard, knock, tuning, etc. was done with this tool. Check it out at http://www.ttspowersystems.com

When I got this truck, I was getting massive knock retard at WOT, so I bought a bunch of the typical tuneup stuff and installed it. ATR wires (suck by the way b/c the crimps keep breaking and I have to constantly recrimp them), Conrad cap and rotor, NGK UR5 plugs, AFPR, vacuum lines, and boost, electronic fuel pressure, and transmission temperature gauges. I then timed it to 0 with the tan wire disconnected.

While I was doing this, I redid my vacuum lines with a silicon hose kit that I found at some hole in the wall aftermarket parts store in Spokane. All vacuum lines were replaced up until the heater controls and vacuum ball on the vacuum circuit found here: http://www.sicid.com/vacuum_diagram.jpg (I changed the cruise control line). The reason I didn't replace every vacuum line was because the stupid kit was made for a Honda Civic or equivalent, so there wasn't enough vacuum line to do it all. If somebody on the board is selling a kit, buy it, unless you live in Seattle, Portland, Chicago, some kind of big city that would carry it. I live in the middle of nowhere, so I was sort of out of luck... Anyway, the most important vacuum lines to replace are the plenum to AFPR and Map sensor, and even more importantly, THE TURBO SOLENOID AND WASTEGATE VACUUM LINES. Replace these if you are having strange boost issues. I was getting knock from boost spikes caused by a vacuum leak here, I'm pretty damned sure. I was getting 17-20 psi in datamaster before the vacuum line replacement, and even though it isn't very accurate over 14 psi since my ATR Pitbull is a 2-bar chip, my boost gauge was agreeing. This is where some of my knock issues were coming from.

I also deleted the EGR from the vacuum circuit, and I haven't gotten a code yet. If I do, all I have to do is pull the ECM B fuse for 30 seconds and all will be well again. This reduced my intake temperatures by almost 30 degrees F. I'm assuming this also helped my detonation problem.

Alright, so all the problems should be gone now right? Wrong. I was getting massive knock under any boost at all. Why?

The main thing that was causing my knock: Timing. My timing chain has slipped a tooth or two, as my TDC is at about 15-20 degrees retarded from where the 0 mark is. I found my TDC with a screwdriver and a wrench on the harmonic balancer bolt. First, I had somebody blip the starter until I felt exhaust come out of the #1 spark plug hole. At the beginning of the exhaust stroke, I manually wrenched the piston up, tapped it with a screwdriver, marked the harmonic balancer with a line of whiteout, took the screw driver out, wrenched the motor over, put the screw driver back in, wrenched the motor the opposite way, and marked when it hit the screw driver again. In between these two marks is TDC. It turns out that when I had timed it before, it was actually almost 15 degrees advanced. Very bad. Lots of knock.

When I figured that out, I set it for true TDC and I had no spark retard and absolutely no knock at WOT any more, but I had a new problem: The boost was stuck at 13 psi for some reason. If it had been 10, I would have known that I was in "limp home mode" or that the boost control solenoid was disconnected or something was going on with it, but it was 13, an odd number.

Apparently an ATR Pitbull chip runs in open loop mode and depends only on TPS (Throttle Position Sensor) input to control the wastegate. From advice from the board, they said to check the wastegate rod, and I did. I set it according to this diagram: http://boostvalve.com/tech/wg-preload.html. This didn't help me. I was still stuck at 13.5 psi or so. Well, I played with the rod adjustment a little bit, but was scared to twist it in too much. I could not get more boost for some reason, so I eventually got frustrated and just twisted the rod super-short. There are probably 8 threads left on the rod right now, but after I did it, I got 15-16 psi. Problem fixed: Don't be worried and twist the arm in for more boost if you have an ATR Pitbull. Twist it out for less.

If you don't have an ATR Pitbull, set the wastegate arm how the diagram explains.

I spent about 2 and a half hours fine-tuning the timing and wastegate arm by trial and error. I did the arm first, giving me ~16 psi, and I then loosened the timing bolt and changed timing until any spark retard was pretty much gone. I set my base fuel pressure at 50 psi, just to make sure enough fuel is getting in. I ended up being about 1 degree advanced with my wastegate rod showing about 8 threads left to get my perfect setup. It WILL be different for you.

Just a note, if you have an ATR pitbull, it is not recommended to tune over 14.7 psi. The 2-bar chip can only read up to 14.7 psi, and does not compensate enough fueling for any more boost than that. If you have an ATR Pitbull, I strongly suggest getting an Ultimate or dig 4-way chip or some other 3-bar chip with a 3-bar map sensor if you plan on running over 14.7 psi of boost. I am looking in to an aftermarket chip right now, and realistically, I should have tuned my truck for 14 psi, but it runs too damned good right now to change. Besides, I don't run the truck w/o datamaster, so problems are usually seen before bad things happen.

Quick summary: When you get a new Ty, do a basic tuneup no matter what condition it is in. Mine was pristine, but I still had to do the following: New plugs (NGK UR5), new wires (I used ATR Black Beauts, but I hate them and would go Taylor next time), cap and rotor (conrad), an AFPR, fuel pump if you don't have it, boost, trans temp (weak link on tys), and fuel pressure gauge whether it be mechanical in the engine bay or electric in the cab, and vacuum lines. Do not forget the vacuum lines near the turbo/wastegate. There are two links you need to replace. Time the beast using the TDC method described above. Get datamaster somehow and learn to use it wisely.

Hopefully all this will solve your problems if you have anything similar to what mine were.

It finally runs like a bat of out hell, and does so consistently.
 

wrx2typhoon

New member
Thanks for the info, looks like i will be replacing some hoses.Among some other things.I want low 12's by the time weather gets nice again, but i want the thing running perfect before i mod.Right now its perfect except for wot
1/2 3/4 pulls great, idles great, Hopefully this will fix my wot prob.
Thanks again
Adam
 

SeattleSy#1255

Category 5 Conservative
bezerk said:
SeattleSy#1255 said:
good for you Ben!

bigger turbo now?

shit, he just spend a whole bunch of time trying to get it right.. :tup:

Enjoy it while it runs! :wink:

yes but a stock truck running right gets old after a week....ok ok, two weeks.

ok, its been 5 years here! :p
 

MikeMcNair

New member
Re: Why would my boost be limited? Datamaster files included.

bringing this back from the dead to thank the OP for the write up!!!

i will look into these things as well. i am having an issue where the truck falls on it's face at ~ 13 psi also, and feels like it is just plain dead. virtually no knock, and only other code is the IAC code (# 35)

my truck runs perfect until ~ 13 psi, and then it starts pulling ~ 1.5* of timing, and basically feels like it is dying, sputtering, misfiring, not too sure what it is.

my injector DC is showing high (~ 120%) and my AFR's are perfect, in fact a HAIR rich (11.8 requested by ECU, 11.2 showing on the PLX)

i have a walbro, new plugs gapped right, new wires, coil, cap, rotor, AFPR, vac lines, etc.

i am running the same boost with or without the solenoid plugged in, which is ODD. actually, it runs lower in 1st gear, than it does in second for some reason too. (12 ish in first, 15-16 in second)

i had to put my WG actuator arm out VERY far to get the boost this low, other wise it was way too high (~ 20 psi)

i do not know what chip or MAP is in the truck, and would love some insight on how to find out. i was told it is stock, but the ECU is requesting 17.3 psi at low throttle, and it is requesting 15.9 at WOT, which is clearly not stock.

my buddy who had a GN a while ago told me that the truck smelled like detonation, which apparent does have an odor to it.

any thoughts and or help is greatly appreciated. i have to figure out why this just started to bog on me.

log2_63degreespulled.jpg
 

MikeMcNair

New member
Re: Why would my boost be limited? Datamaster files included.

ok guys, i am really stumped.

every now and then i am throwing a code 43, but it goes away. i found a plug wire (300 miles on it) that was ripped, so i replaced it.

i pulled all the plugs, and 1/2 of them were all sourts of crudded up. (basically, looked like they had been breaded, like chicken :) )

cleaned them up, gapped them to .028 (per Nolan's suggestion) and went out for a spin. EDIT: i am running NGK UR6IX, per nolan's suggestion, could that be the issue? everyone seems to say UR5 in all the threads i am finding......

well, same issue is happening. truck runs awesome, then just falls on it's face. it happens around 3200 rpm's, and you can see it on the log below (look at the dip in the RPMs)

93 octane, solenoid plugged in, AFPR set at 42# (vac line off) AFR's in the 11.1 range at WOT, walbro kicking just fine, trans shifting well etc.

i have no idea where to look, since everything SEEMS fine, and the logs seem great, then it stumbles....

any ideas are greatly appreciated!!!!! thanks in advance!

47degreespulledatthestumble.jpg
 
Last edited:

fivetodrive

CRISPY
Re: Why would my boost be limited? Datamaster files included.

Fix the knock first. It looks like it starts at about 4 lbs of boost and never goes away. If you don't have any race gas handy add some Xylene to the tank and see if you can get rid of the knock. You are also at 100% DC on your injectors. But they have been known to go 120%

Start with the easy stuff...
 
Top