Recent content by bshaw

  1. bshaw

    749-Vortech-928 with new 5.0L

    Re: 749-Vortech-928 with new 5.0L I don't think NB vs WB is the big issue here. I'm dealing with something seriously whacked, not fine tuning. NB tells me enough to know it's going real lean. Not enough to tell me the exact AFR, but enough to know it's lean. Not the best tool but...
  2. bshaw

    749-Vortech-928 with new 5.0L

    Re: 749-Vortech-928 with new 5.0L No, no wb hooked up yet, just a nb and a led display.
  3. bshaw

    749-Vortech-928 with new 5.0L

    Re: 749-Vortech-928 with new 5.0L Values in F29 are already about 50% higher than what I ran with the last engine. You're thinking I should keep on going with adding more fuel to F29? I'm still running the stock code. Looked at code59 but didn't pursue it because of the 3 bar map issue, one...
  4. bshaw

    749-Vortech-928 with new 5.0L

    Re: 749-Vortech-928 with new 5.0L No boost at this point, this is just off idle so still in the vacuum domain. I've not messed with F77 yet, I need to get the light cruse stuff working right before I go to boost. Thanks,
  5. bshaw

    749-Vortech-928 with new 5.0L

    Please excuse the somewhat off-topic post, but it is sort of related. The subject is a 1984 Porsche 928 5.0L v8 with a Vortech supercharger controlled by a GM1227749 ECM. I ran a similar configuration for several years and many track hours, it was running pretty well until I lost compression...
  6. bshaw

    Anyone in CT?

    Is anyone here in CT with some data logging hardware/software? I'm having a bit of trouble with data errors, it would be great if I could plug in some known good hardware and see if my troubles go away. Thanks,
  7. bshaw

    Chilled Gasoline?

    My 928 has a fuel cooler installed from the factory. There's a small (coke can) sized canister the fuel flows through before returning to the tank. The A/C line runs through it on the way to the interior. Theory is that idling in traffic on hot days, the fuel returned to the tank from the...
  8. bshaw

    New heads, new troubles (somewhat OT)

    So I'm not loosing it. Ok, maybe I am, but not on that particular point :-)
  9. bshaw

    New heads, new troubles (somewhat OT)

    Re: New heads, new troubles (somewhat OT) GM module, lt1 TB, IAC, IAT, TPS. The rest of the sensors are Porsche (Bosch). The Porsche distributor has an output that feeds directly into the ignition module to provide reference pulses. Works like a champ. Narrow band O2. Yep, gotta get...
  10. bshaw

    New heads, new troubles (somewhat OT)

    Yes, I need to make that leap to WB02. I'm having troubles just data logging right now, loads of data errors. I fould a mention here of grounding the laptop case to the car, going to try that tonight. Ahhh, open loop while tuning! I should have remembered that! You can tell I haven't...
  11. bshaw

    New heads, new troubles (somewhat OT)

    I say OT because the subject is a supercharged Porsche 928 controlled by a 749. I hope you guys don't mind a question or two from me from time to time, but I'm not sure where else to ask 749 questions. I'll stop if you guys object. If you remember, I supercharged my 928 4.7L v8 track car...
  12. bshaw

    749 low Z mods

    I've added a page detailing my low Z injector driver mods for the 749: http://mywebpages.comcast.net/p-928/749mods.html Enjoy!
  13. bshaw

    Wastegate control question

    Hi gang, I just got the supercharger installed in my 928, it's working pretty well (boost is goooood!) I'm working a blowoff valve into the system now and would like to control it with the 749's wastegate output. My question is: does the wastegate get actuated when the throttle is closed...
  14. bshaw

    749 in a 928 - MAP troubles

    Bwahahahahaha...it's alive, IT'S ALIVE!!! Running pig-rich, but running! To answer my previous question, the sense resistors have to be changed as well as the driver mosfets to run the 8 p&h injectors. You need 1/2 the resistance so paralleling in a pair of .1 ohm, 2W resistors did the...
  15. bshaw

    749 in a 928 - MAP troubles

    I'm making some progress here. Got the plenum back and everything installed again. I've been chasing a problem with injector pulse width. I found the sense jumpers wrong on my test bench. Once I fixed that it started working properly. I can clearly see the fixed pulse and the variable hold...
Top