Re: Brake pedal to floor, new MC and ABS delete
I have not finished the new brake lines so I do not know if the ABS delete helped. I guess the first thing to do would be to look for leaks from the wheel cylinders, lines, etc. Beyond that I can't really help you.
Re: Brake pedal to floor, new MC and ABS delete
I guess my next step is to test the MC. I am going to work on making a plug so I can plug the outlets and see if the pedal still creeps to the floor. I will try to do this asap but I am pretty busy.
Re: Brake pedal to floor, new MC and ABS delete
I did not see any leaks. I have looked at the wheel cylinders. Can the combination valve go bad? That would be the only other thing I could imagine besides the ABS unit or the MC.
My truck's brakes are giving me a major headache. The original problem was that the pedal was slowly going to the floor as if there were a leak. At stoplights it would eventually begin to creep forward until I pumped the brakes. There was no fluid loss so I replaced the MC with a remanufactured...
Re: Help with Datamaster file
Somebody also suggested that it may be the fuel pump. What do you guys think of that? It makes sense since the fuel filter was clogged. Any thoughts? I guess the next thing to replace will be the fuel pump once I get the brakes figured out.
Re: Help with Datamaster file
The reason it didn't happen is the second one is because I ran out of pavement to keep going. It was just starting to stop accelerating the instant I let off. Only the last data point or two will be showing this symptom. I am sure that it was starting to happen though.
Re: Help with Datamaster file
The truck is completely stock. The IC pump is hotwired on so in the first file that explains the IAC temps. It also seems to shift ok from 1 to 2 but it does not from 2-3 and 3-4. It pulls hard up to around 4000 rpm and then seems to lose power and hang at that rpm...
Re: Help with Datamaster file
I found my ALDL cable and took the Syclone for a drive today. I got it idling cold and warm. Are both OK? Perhaps I am imagining the increased roughness after it is warm. This file also has lots of driving around and one short full speed blast at the end. There...
Re: Help with Datamaster file
OK so I am back and today I adjusted the TV cable as instructed on that writeup. I also hotwired the IC pump (it was not hotwired at the time when I got that dm file). My brakes are not working well so I am not going to do any at-speed testing. I am going to have...
Re: Help with Datamaster file
Ok when I get back in a month I will try all this stuff. Thanks for all the good ideas. I am currently on the other side of the country and am about to go internetless for the next month.
Re: Help with Datamaster file
I live at 7000ft but 23.9 is too low if that is measured in mmHg. Does the computer get its baro reading from the MAP sensor? Is there a way to test that? I know I didn't shift into park, maybe I missed OD and went to neutral. Does my boost around where the truck...
Re: #2293 Syclone has a new home
Thanks! check out my thread in Chipping, Emissions and Tuning:tup:. Also, does this truck look lowered in the rear? It has a small lowering block but I am not sure if it is stock.
So here are my problems, stock truck with 81k miles:
1. The truck has a rough idle, only sometimes. I am guessing that this is dependent on whether it is in open or closed loop. What should I do to check the o2 sensor?
2. The truck has trouble shifting 2-3 and 3-4. You only see the 2-3 shift...
Hey, a few weeks ago my dad bought me Syclone #2293. It was owned by an old man who bought it new and used it for a daily driver until he was unable to drive. After that he would start it up and drive it on occasion. It has 81k miles. I think it was well taken care of. It is completely stock...