Recent content by Tim Zapoluch

  1. T

    What more do i need??

    Hi. You have to start the romulator program. then you select the chip your emulating, which should be a 128k chip. then you go to load buffer, and browse to select the bin you want to use. then you click on the buffer to rom tab, I think it's the very top one on the left side of the screen. I...
  2. T

    It lives!

    Got my motor running yesterday, seems like it is going to be a powerhouse once tuned.... right up until the oil line on top of the turbo blew off. The ecm was running off the eprom at first, but now all I can get is limp home mode, no matter what I try. Thats ok for now, as the motor actually...
  3. T

    Ext Wastegate, Ultimate, and Stock boost control??

    I'm not quite sure how the vac lines are set up. it seems to me that the wastegate seloniod duty cycle would be adjustable for the reasosn stated. As I understand it, the wastegate itself can only flow so much so fast. In order to drop the turbine speed, exhaust is bled from before the...
  4. T

    Could we use this map ecu?

    seems kinda limited, for the price, doesn't it?
  5. T

    Ext Wastegate, Ultimate, and Stock boost control??

    The chip controls the wastegate duty cycle, which means that the program is taking in account the legnth of time needed for the wastegate to bleed a certain amount of exhaust. with a external, larger wastegate, the duty cycle would have to be shortened, I think, since the wastegate would have...
  6. T

    Any last suggestions to get rid of knock retard before I go

    I've been told that pouring a cup or so of distilled water down the throat of a revved motor will help to wash out (steam out, more likely) the combustion chambers. There could be some carbon buildup causing knock. Is the wastegate sticking or is there a pinhole leak in the line that is...
  7. T

    trouble with datamaster

    I had the same error. all i did to get it to work is just keep trying, it eventually worked. make sure the cable is plugged in all the way. sometimes they exhibit "nintendo syndrome". if you had one, you know what I mean. is it the stock chip in the computer? Tim
  8. T

    Datalogging errors and miscommunications.....

    I know this might sound like (and be) a royal pain in the ass, but, have you tried shielding the plug wires by wrapping them in aluminum foil? they have to be grounded at one end only. Maybe try wrapping the wire between the aldl connector and the laptop. once again, ground one end only to...
  9. T

    First time engine startup w/ new cam

    Turbo is a garrett off of a ford merkur, to3, i can't remember the turbine and compressor specs for the life of me, but i'll write them down. I just got my romulator yesterday, i think there was a bad connection in the chip end of the cable, but it's working now. I had an idea for the cable...
  10. T

    First time engine startup w/ new cam

    I origilally selected the '749 based upon the same thought: displacement per cylinder. it's out of a turbo sunbird, 2.0L . the 3.1 was only marginally larger, which i was going to compensate for by raising the fuel pressure or using slightly larger injectors, perhaps the same perctenage more...
  11. T

    First time engine startup w/ new cam

    Hello. the 3.1 I have is actually a 2.8 stroker. 2.8block, 3.1 crank, so it does indeed have a distributor. as to the stock injectors, I went as far as to pick up another ecm from a 3.1, it's a 16196397 flash pcm, p6 family, out of a 95 grand prix. I was just going to wire that one on...
  12. T

    The EST or the ESC?????

    I had a problem similar to this on a 87 gmc pickup, with a '165 ecm. I fixed it by cleaning the ground connection on the gooseneck. the problem soon returned, so I re-located the ground to a better spot. I don't think the intake manifold is the best place to ground the ecm, seeing as the...
  13. T

    promgrammer

    Thanks. I think i'll figure it out. I just wanted to be sure it could be done.
  14. T

    Installing Distributor

    Usually you can get the oil pump drive shaft to line up by turning the crank pully bolt with a breaker bar/socket, as this keeps the distributor in time with the cam. sometimes bumping the starter moves it too far too fast, but usually works well. Tim
Top