Recent content by typhoonesq

  1. typhoonesq

    Crankshalf Help - I think my motor has the wrong crank

    Bought truck with obvious rod knock. Motor out and torn down. Found #5 spun and mains 2 and 3 wiped. SO..............................off to the machine shop. Magnfluxed ok'd, ground down 20 on the rods and 30 on the mains...ok. Time to balance and the setup won't balance. Shop says needs 80...
  2. typhoonesq

    Parts Lists and Suggestions

    Getting my motor back from the shop. I searched for hours and can't find a condensed section or write up on the ancillary parts need to put this thing back together. Did I miss it? I wouldn't doubt it. I need to know the following: (1) Anyone make a complete gasket set? Part # (2) Head gaskets...
  3. typhoonesq

    Kenne Bell Pistons and rings mounted to Eagle H-Beam Rods ---

    Re: Kenne Bell Pistons and rings mounted to Eagle H-Beam Rods --- I'm a board memeber:lol:. I pm'd you.
  4. typhoonesq

    Vortec Short Block / stock heads buildup

    I'm looking to acquire a vortec short block. I plan on using the original heads and everything else as well. My original block spun rod bearing. A couple of questions: (1) Whats the best year block to use? Can I put my old heads on the vortec block? (I know vortec heads are the way to go but $...
  5. typhoonesq

    Question about new vortec long block

    Re: Question about new vortec long block Well at this point i'm going to getting that Vortec and carefully tuning it. Should be interesting. Stay tuned.
  6. typhoonesq

    Question about new vortec long block

    Re: Question about new vortec long block Originally I was looking to spend $2500 to rebuild my engine with 4 bolt mains, new forged pistons, rods, machine work etc.... Realistic ()? Spend another $1500 or so on vortec heads and the list goes on...... That same money will buy me a BRAND NEW 4.3...
  7. typhoonesq

    Question about new vortec long block

    Re: Question about new vortec long block Originally I was looking to spend $2500 to rebuild my engine with 4 bolt mains, new forged pistons, rods, machine work etc.... Realistic (:roll:)? Spend another $1500 or so on vortec heads and the list goes on...... That same money will buy me a BRAND...
  8. typhoonesq

    Question about new vortec long block

    Re: Question about new vortec long block I can't say my tuning skills are great considering I've never tuned a anything but I've read a lot of posts here and will be getting the necessary software. It seems regardless of how well the motor is build, a tune is absolutely necessary for these...
  9. typhoonesq

    Question about new vortec long block

    I did some searching but found nothing really on point. This is what i'm considering: (1) Rebuilding old block (bad rod) with 4 bolt mains, forged pistons, eagle rods, bearing etc.. With machine work and parts I'm probably looking in $2500 range. or (2) I just found a very low milage 4.3 L35...
  10. typhoonesq

    Another new TY owner - The Project has begun!!

    Re: Another new TY owner - The Project has begun!! Purchased off craigslist. Guy i purchased it from had no mechanical background and was clueless for the most part on what was wrong with the truck. Pics coming soon. Truck # is 0693. Red/black. No accidents and very well preserved. KB cat back...
  11. typhoonesq

    Another new TY owner - The Project has begun!!

    Just purchased today: 1992 Typhoon 51K original two owner originally from Texas. Truck is MINT from front to back EXCEPT for a rod or main bearing knock :rant:. The truck was advertised with the knock. Not quite sure yet. Just got it into the garage and will be investigating prior to total...
Top