Head gasket questions...

BMFB

Not to scale
Re: Head gasket questions...

I've run the stock style vicotor renz gaskets through hell and back. If I was running over 25lbs of boost all the time I might think about something else, but I don't think they let go without some detonation thrown in the mix. I personally run these to act like a fuse for the motor.
 

Throws

Active member
Re: Head gasket questions...

And my question remains unanswered: WHY?

Mainly because I'm curious as to why they're never mentioned as alternates. I like to know all my options before committing. I'll probably go with the VR set, but having these discussions take place helps answer questions that I don't see asked/answered.

-P
 

Icarus-54

Donating Old Member
Re: Head gasket questions...

I use fel-pro #1002's sprayed with copper coat,never had a problem.Ya get what you pay for.
 

Damian

Member
Re: Head gasket questions...

I use fel-pro #1002's sprayed with copper coat,never had a problem.Ya get what you pay for.

That's what I did, but I use copper coat on damn near all gaskets. Stuff works great. Built 4 motors using it and never any leaks.
 

Don W.

Stab it and steer it
Re: Head gasket questions...

but I use copper coat on damn near all gaskets. Stuff works great. Built 4 motors using it and never any leaks.

And I've always installed my head gaskets bare. No leaks either. Go figure.:roll:
 

Throws

Active member
Re: Head gasket questions...

Whelp... called Felpros techline... he apologized but said there was nothing they offered for our application. He said anything being used on our trucks from FelPro is "off-label" and they couldn't guarantee any success. Ordering a set of VR tonight.

-P
 

BMFB

Not to scale
Re: Head gasket questions...

the biggest thing is what your using to attach your heads to the block. I say get at least the ARP bolts, the studs if you want to spend the extra.
 

Throws

Active member
Re: Head gasket questions...

the biggest thing is what your using to attach your heads to the block. I say get at least the ARP bolts, the studs if you want to spend the extra.

Looking at ARP v8 sets #134-3701 or #134-3601. 1/2 the price, same bolts?

-P
 

sytyguy

Moderated User
Re: Head gasket questions...

Looking at ARP v8 sets #134-3701 or #134-3601. 1/2 the price, same bolts?

-P
Correct, get the SBC set and use the necessary bolts. FWIW, I sell them for:

Hex Head - 134-3601 - $75 set
12 Point - 134-3701 - $78 set
 

DaveP

Active member
Re: Head gasket questions...

I don't believe it's correct or desirable to put any coating whatsoever on a composition head gasket. Install them dry. It defeats any sealing properties designed into the factory coatings by the manufacturer.

In the past I've used numerous "steel shim" OEM gaskets in my SBC and BBC builds because they don't require re-torquing as do the composites mentioned earlier. For steel shims I apply a coat of Copper Coat, and allow it to dry before installing. Steel shim head gaskets tend to seep around some of the holes in the deck when applied to a "used" non-prepped surface. The Copper Coat seals these minor imperfections.

But composite gaskets should always be installed dry.
 

Throws

Active member
Re: Head gasket questions...

[...] Steel shim head gaskets tend to seep around some of the holes in the deck when applied to a "used" non-prepped surface. The Copper Coat seals these minor imperfections.[...]

What defines a prepped surface? A surface that's newly machined? How would you prep a used surface? I've heard that scotch-brite pads are OK, sometimes they're frowned upon. I know the 3M Scotch-loc products are a no-no.

-P
 

DaveP

Active member
Re: Head gasket questions...

What defines a prepped surface? A surface that's newly machined? How would you prep a used surface? I've heard that scotch-brite pads are OK, sometimes they're frowned upon. I know the 3M Scotch-loc products are a no-no.

-P
You've got it. Blocks are vary rarely resurfaced during an overhaul or rebuild. There are often minor surface imperfections present such as corrosion around coolant holes and minor scratches. This is an un-prepped surface in that the builder has no control over the surface finish or quality. He didn't prep it with machining.. A freshly milled head has a prepped surface.

I scrape any chunks off with a scraper and razor blades. I then hit it with a wire cup brush in my 4" Makita angle grinder. Wipe it with lacquer thinner to ensure an oil-free surface for maximum adhesion, and install the head.

Scotch Brite pads shed abrasive residue during use. Not what you want in the cyls after the pistons have been installed. Scotch Brite may be an OK technique during cleaning operations of a bare block. But to clean the deck as part of a head R&R with the pistons in the block, no.
 

DaveP

Active member
Re: Head gasket questions...

One other thing about head installation. I always run a tap in every threaded hole for the head bolts. I also clean the bolts on my wire bench wheel. This assures clean threads, and an even torque. If the heads are surfaced, and the bolts not cleaned the threads will have build-up at a point that used to be just above the deck surface, but will now be rammed into the threads, because of the decreased head thickness.

Clean threads in the block and on the bolts will promote even and consistent torque. Which will result in maximum gasket compression.
 

Don W.

Stab it and steer it
Re: Head gasket questions...

One other thing about head installation. I always run a tap in every threaded hole for the head bolts. I also clean the bolts on my wire bench wheel. This assures clean threads, and an even torque. If the heads are surfaced, and the bolts not cleaned the threads will have build-up at a point that used to be just above the deck surface, but will now be rammed into the threads, because of the decreased head thickness.

Clean threads in the block and on the bolts will promote even and consistent torque. Which will result in maximum gasket compression.

X2. Forgot about that Dave. Since I consider head/seal one of the most important parts a build I've been known to run a head bolt down each hole just so I know. :roll: An actual tap, as opposed to a thread cleaner, can remove metal so care should be used.

http://www.summitracing.com/parts/SUM-900200/

I've never used these but it's worth considering. Cheap insurance if you will...
 
Top