Need Help,, Ty Still Wont Start......

VermontTy

Support Our Troops
Re: Need Help,, Ty Still Wont Start......

Stefan, read through my issues and see if there's anything that might ring a bell. It's not the exact same thing, but there may be something in there that jogs your memory.

http://www.syty.net/forums/showthread.php?t=29986

Something I haven't heard mentioned is the vacuum line to the pressure regulator. Vacuum for it comes off the backside of the manifold; it goes to a T fitting where it splits and goes to the MAP sensor and pressure regulator. Do you have an adjustable regulator? When setting my fuel pressure, if the line was open going from the plenum to the pressure regulator, the truck would not run. I had to plug it with a bolt while I set the pressure. Double check that you haven't knocked it loose or off in your messing with the distributor; I did it twice in my adventures above, but caught it before I cranked and cranked.

Don W. said:
BTW if you ARE getting fuel then there's a bunch a gas throughout your system: intake, exaust ect.
It would be smart to change the oil too.

============EDIT===============

You didn't pull your distributor out while you were replacing the ignition module, did you? Are you sure you plugged the pick-up back in (I think green plug?) when you reinstalled it? It's kind of hidden underneath the reluctor area.
 

Priceless

New member
Re: Need Help,, Ty Still Wont Start......

Ok this is what i have gotten to..... I checked everything over again and im not getting spark... But now it gets confusing... I thought it might be the Ignition module so i pulled it out and went and got a new one... Still nothing.. Checked the pickup coil with a multi meter and it reads fine.. The coil is getting power from the red wire and the wire form the coil to the distributer checks out good.. so i tried to get spark right from the coil... Nothing came off of it.. So i though maybe my new MSD coil went bad... Went out and bought a new oem coil... Pluged it in and nothing.... Is there a voltage regulator or something...

Where does the gray/white wire from the gray plug to the coil go????
Is that wire a ground??? Im lost...
Would that wire cause no spark...
When i crank the Ty over the tach zeros out everywhere.. Do i have a short?? Thank you all for the help... I feel like im going in circles....
 

Don W.

Stab it and steer it
Re: Need Help,, Ty Still Wont Start......

Somebody chime in here if I’m nuts but the way I read the manual you can disconnect the 4 term connector and still test for spark.

The following does make sense:

If still no spark then plug in the 4 term and disconnect the C/+/B term on the module and check for 10 volts or more (key on, of course) at the + and C at the dist harness connection. If good than the harness, which goes to the coil, is bad. In other words C and + are the low voltage feed to the coil. No low voltage in, no high voltage out.
icon_smile.gif


Hope this helps a little.
 
Last edited:

GMCSyclone1

NASTE MEMBER
Re: Need Help,, Sy Wont Start......

Re: Need Help,, Sy Wont Start......

I finally got the truck back together and it will not start. It was running fine before. I have a new plugs, cap & rotor. I checked the egr it works fine truck is getting fuel and spark but will not turn over. I did paint the motor but i covered everything well. The first time I tried to start the truck it seem to kill the battery instantly, I checked my grounds and notice one did have a little paint on it and it wasn't making good contact. Now the truck cranks but it doesn't crank very long its like a serious of short cranks and then one long one. Guages jump boost and tach move oil pressure and voltage and everything electrical is in good working order but I can not figure out what is wrong. I never messed with the timing so I can't see how it would be off. The biggest problem that I still notice is that when I try to crank it the battery is being drained very quick are there any suggestions?
 
Last edited:

Don W.

Stab it and steer it
Re: Need Help,, Ty Still Wont Start......

Based on your description and assuming you didn’t actually remove the dist. and it ran before, then your plug wires are out of order.

Click here and then on “distributor.”

http://home.swbell.net/loeryder/

This assumes that your dist. is in the factory location. In other words it hasn’t been removed and reinstalled with the rotor in a different location.
 

GMCSyclone1

NASTE MEMBER
Re: Need Help,, Ty Still Wont Start......

I may not be a smart man but I know what dumb is. Well now that I might be the dumbest syty owner on the board I can proudly say the sy is running again :rock: Thanks Don you hit it right on the head I actually figured that out while the site was down but when I came back in and checked you were right. I don't know how I managed that but I did :banghead: I would like to thank everybody on the board for their support and help and I am happy to say 2707 rides again. I will post pics of the cleaned up motor once I find my cable for the camera. Thanks Again Everybody!
 

Don W.

Stab it and steer it
Re: Need Help,, Ty Still Wont Start......

You be welcome!

Remember there are two kinds of people. Those who have, and those who will.... make whatever mistake you'd like put here.
icon_biggrin.gif

Glad you figured it out.
 

Priceless

New member
Re: Need Help,, Ty Still Wont Start......

WOW... my thread helped someone..... good to hear it.... my truck is still just sitting in my garage... not starting... I think its a ground but dont know where to look... my tach Zeros out when i try to start it... I didnt touch any of the electrical though... and im getting tried of taking this thing apart and then putting it back together with no improvement.. oh-well....
 
Re: Need Help,, Ty Still Wont Start......

Same thing just happened to me yesterday cost me a $200.00 tow i replaced the distributor and it started right up..
 

Priceless

New member
Re: Need Help,, Ty Still Wont Start......

Took it to the shop the other day.. i completely gave up what it might be... Well they call me up not even 2 hours later telling me the PICK-UP coil was bad... so $300 later my Ty is fixed and runs... While i was trying to fix the Ty i took off the cat and exhaust.. Since i live in Cali i had to put it back on for emissions.. Before i got the exhaust put back on all i have to say is what a difference.. It was so much more faster with out the exhaust.. the turbo spooled so much faster... it was great just a little to loud... Now the ty seems to have a miss or something.. while idling the ty every once in a while seems to stumble.. as if it wants to die... no error codes.. i gonna replace the fuel pump next.. preventitive matnence... i missed driving the ty... glad its up and running again...of course driving the GTO all the time wasnt all that bad...
 
Top