Need Piston / Rod knowlege

Ian Turgeon

Cascading Inspiration
If anywone with some good knowlege on the different pistons and rods would do a a little tech talk here, I'd like to post an article on SyTyArchives.com.

What I'm looking for.

piston/rod general tech
piston/rod characteristics
part numbers
specs

Come on guys, i know theres a lot of knowlege out there on these, lets get this organized, as I've recieved quite a few requests through my site for this info.
 

myclone

Donating Member
I can prolly help a little. Then again maybe Im just rambling. :grin:

Here's what I know/have been told by the likes of Sonny Leonard (engine builder):

TRW forged pistons are slightly heavier than J&E or Arias wrist due to a heavier wrist pin.

TRWs are extremely durable unless subjected to lots of detonation. J&E survived a detonatious 4.3 eng I had dealings with when the TRWs didnt. Maybe they are "softer" than the TRWs or just not as "well made". I dunno. Im not metalurgistessessistesss...

TRWs dont have wrist pin oiling holes where as the J&Es I used did.

The rods Ive dealt with were the factory stuff prepped in various ways. Heres what I found:

1st set were just balanced and deburred. Survived many trips to 8k+ RPM in a 2wd s-10. This truck was not able to "hook up" so the rods didnt get loaded real hard. Only stress they endured was massive amounts of RPM any time the truck was being driven. :grin:

Second try were the above rods with the beams deburred, polished, then shot peened. They held up to the same abuse and looked fine on tear down after a full summer of being beaten to death.

Third go round... Same set of rods but had the ARP "waveloc" bolts installed. These rods lasted ~2seconds into a 8k+ burnout before scattering the eng. When the eng was torn down the rod caps that were still attached to the rods had to be pried/beaten out of the eng.

After some research it was found the rod/cap bolt holes were not sized for the waveloc bolts properly. The rpms stressed the big eng of the rod enough to cause the bearing clearance to change. This grenaded the bottom end of the eng. So much for me ever using Terry Walters Performance machine shop...

Well, I know this prolly doesnt contain the info you were really after or numbers/graphs/flow charts but it is what Ive had experience with for the little 4.3. Might help someone decide what kinda path they want to take with putting togeather a rotating assembly.

I got some info about the diff between the SB rods and V6 rods but I figure most ppl already know the differences anyway so I wont bore you with repeating it.
 

Captain Morgan

Moderated User
On 2001-12-12 16:23, myclone wrote:
I got some info about the diff between the SB rods and V6 rods but I figure most ppl already know the differences anyway so I wont bore you with repeating it.

I would be interested in hearing about it :grin:
 

myclone

Donating Member
Someone actually wants me to type more info???!! There IS a God after all!!!


The diff that I know of are the big end width and the chamfer. Due to our engines being non common pin (each rod has its own crank journal)the rods have a bevel or "chamfer" on BOTH sides of the big end where as the SB stuff only has it on the fillet or "outside" of the big end.

SB are "common pin" or two rods share a crank journal. The SB rods only need the chamfer on one side of each rod to clear the fillet on the crank. Our stuff has the fillet on each journal also but only one rod takes up residence there. Hence the need to have the chamfer on both sides. Rather than just take a SB rod and add the chamfer to it GM, in its infinite wisdom :roll: , narrowed the big end AND added a chamfer for the 4.3.. Why they did this I'll never understand but Im sure there is a reason.

Rod bearings are corrospondingly narrower also for us. Mane bearings are same as SB stuff.

Other than that the rods are the same as far as I know/remember.

FWIW, if you do a odd fire 4.3 using the "common pin" crank then SB rods drop in with no fuss/no muss.. Havent done one of those yet as Im too stupid with puterized tuning/engine management to even try (for now :grin: ).
 

Ian Turgeon

Cascading Inspiration
any more input? come on guys.
Just think, if you type it this one time, you wont have to type it ever again.
Q:
"whats wrong with my pistons, why do i have to buy twr's how long should i get my rods? do they smell good, can i paint em with chromillusion?"

A:
uh, go to sytyarchives.com/howto/
 
Top