Recommendations for heat shielding?

crashing_sux

Blow Me?
I keep reading that I should put some sort of heat shielding around my spark plug wires when I change them, can anyone tell me what type to look for and where to find it?

Looking at my current setup it appears the previous owner put two types of heat shielding on, one feels like a fabric with a shiny metal coating, reminds me of those asbestos gloves you use when working with hot stuff, the other looks basically like a red section of garden hose, maybe a little more supple.

Are there other types, is one better than the other? And where the hell do I get this stuff? The current stuff is toast, my headers got red hot once and now my truck runs like crap, the latest trick is it's been running for five or ten minutes then just dying, forcing me to sit around 20 minutes before it restarts. I hope plugs, wires, cap and rotors will fix that (going on this weekend) but I definitely need new heat shielding when I do it as the current stuff is all burnt, powdery, and flaking off.

Looks like I might have ruined the coating put on my headers by getting them that hot too :(
 

TYRODD

My ass. Look at it.
What you need are called "spark plug boot protectors". They are fiberglass sleeves that slip over you spark plug boots. They are probably 7" long and really work well IMO. You should be able to find them in a speed shop or the performance/ignition section of a chain auto store. I think I paid ~$20 for two...kinda pricey but they dont really go bad and they will save you cash in the long run. Taylor spiro pros or MSD 8.5s seam to take heat better than most other spark plug wire Ive found :tup: .
 

Ian Turgeon

Cascading Inspiration
Talk to Mike Hood here, he can get you the boot protectors for a pretty good price. I've got those on my sy now, cant attest to them except for the fact that putting them on 90 degree ends is very difficult.

It sounds like you have the cheaper reflective DEI stuff you can find in Summit along with a Fire Sleeve. The fire sleeve stuff should be able to handle whatever you throw at it, however there are a lot of imitations.
 

crashing_sux

Blow Me?
I picked up a set of the Taylor boot protectors locally, there are no instructions with them and they are of a different design than what I did have.

These have a ring in one end making the opening very small, just slightly larger than the opening in the end of a spark plug wire. Am I supposed to remove the boot from the wire, put the protector on, then put the boot on and slide the protector up on the boot, or is that ring supposed to sit over the spark plug with the rest of the protector going over the boot?

I feel dumb asking this but it really doesn't seem obvious to me, I guess I'm not sure whether this protector is intended to only protect the wire or if it's supposed to cover the boot as well.
 

Ian Turgeon

Cascading Inspiration
I spent a great deal of time getting those rings to fit over the spark plug boots, so If I were to find out that in fact they arent supposed to do that at all, then I guess I found why it was such a difficult task.
 

Try Me

New member
Yea, i have those also along with the shielding that goes over the entire plug wire (cant remember the brand but its the same texture as those boots).

I bought a roll of 8.5mm msd wire and the summit tool and make my own plug wires so its a little easier for me, but you are supposed to take the boot off and slide those boots over the wire so that the larger end goes over the boot and plug and the small ring goes up over the wire. It obviously is easier when you are making a new wire. they do work well though, i used to have alot of trouble burning plug wires even after the 2000 degree jet hot coat
 

crashing_sux

Blow Me?
That's funny that you guys both said that (the ring goes over the wire) as I have been googling a bit and finally found a site that sells them that had the note next to them...easy install, slip the wide end over the boot and install with the ring between the boot and the spark plug.

So that's what I did. Seems reasonable to protect the boot as well. I had some extra fire sleeve stuff that I wanted to use as well, behind the boot protector but I would have had to remove the boot and wasn't sure if that was a good idea.

One strange thing I ran into, I just bought the Black Beauty plug wires and the 45 degree plug for # 6 won't click on. I played with it a bit and couldn't get it to click (or grab) onto the plug it just slid on, and slid right back off. I tried pinching it with pliers a bit to tighten the ring up that is supposed to grab the plug but that didn't work either. Any way to tighten these up? I just used my old plug wire for 6 until I can get the black beauty working as it was getting dark and I wanted my truck running.
 

Ty0279

Historically Significant
SyTyArchives said:
Talk to Mike Hood here, he can get you the boot protectors for a pretty good price. I've got those on my sy now, cant attest to them except for the fact that putting them on 90 degree ends is very difficult.

I put some on my Ty a couple months ago. Yeah, getting those things on was really difficult, especially when the wires were already on the truck. :x

I picked mine up at NAPA for about $5-$6 each. I'll be calling Hood next time though.
 

SpoolingTurbo6

Donating Member
the shiz-nit

the shiz-nit

this is what I used on mine :lol: from Mc Master Carr ...good stuff
Temps up to 1400* 8849k55 or 1200* 2592k56 neat stuff

Quote    1400°  F Fiberglass Sleeving— This tightly knitted fiberglass is stronger and provides the best temperature resistance of the fiberglass sleeving we offer. Resists most acids (excluding hydrofluoric), alkalies, oil, grease, ammonia, and detergents. Temperature range is -70°   to +1400°  F. Wall thickness is " Color is white. To Order:  Please select from available lengths of 5, 10, 25, and 50 ft. Maximum continuous length is 50 ft.
go to www.mcmastercarr.com search part #

your welcome
Tyson
 
Top