Unbreakable Poly Motor Mounts INSTALLED !

Tydriver

TurboLS6 Powa'
Well ladies and gentlemen (Bdubb, the 1st one applies to you :wink: )..

Jeff and I installed the ES Poly Mounts with his adapter plates in my Typhoon today.

YES IT CAN BE DONE WITH THE ENGINE INSTALLED

I have my truck pretty much disassembled for the assault on the Vortec heads.. No Doubt this indeed made it easier but I have NO problems believing it CANT be done on a truck that still is assembled. My suggestions are to remove the Exhaust for access and a couple other smaller things.

Anyhow... Heres the pics, I elected to go with the BLUE mounts from ES so they would compliment my blue truck. Also makes it easier to spot them in the pictures.

Heres underneath looking at BOTH of them installed:
bothpoly.jpg



Heres a closeup of the PASSENGER SIDE:
passengerpoly.jpg



And last but NOT least... The DRIVERS Side:
driverssidepoly.jpg


Hee hee.... No more broken Motor mounts for me.. The Drivers side literally came out in 3 pieces total ! And was trully worthless.
 

ParTyBoy

New member
On 2002-02-09 23:54, ALBERTAN wrote:
Put the heat shields back on or go buy another set of ES mounts now. :wink:

Sorry don't have any experience with motor mounts ,but what heat shield... pics???
Something I'll need to know when I get around to replacing mine eventually...
 

Tydriver

TurboLS6 Powa'
On 2002-02-09 23:54, ALBERTAN wrote:
Put the heat shields back on or go buy another set of ES mounts now. :wink:

Well unfortunately, I dont think thats gonna happen... The stockers literally CRUMBLED when I got near 'em... I intend on coming up with something that will work however.. Anyone know if they are offered as replacement items from GM ?? Part #'s ??

Otherwise I have a few ideas.....


Thanks for the input however.
 

Tydriver

TurboLS6 Powa'
Sorry don't have any experience with motor mounts ,but what heat shield... pics???
Something I'll need to know when I get around to replacing mine eventually...

I'll post a pic of the top end of my truck, U can see the OEM heat sheilds in place, since they were pretty much toast I decided it was worth destroying them to facilitate removal of the remaining mount... However if you can save them and U elect to do so, be prepared for some extra headaches. Unless of course U change them at engine overhaul time.

Heres the pic, notice where the mounts are, there is SUPPOSED To be a heatsheild blanket type material... Like I said, SUPPOSED TO BE

shortblockty.jpg
 

TurboTony

Active member
Just to add to what Dean is talking about, the drivers side motor mount came with a heat shield from the factory. When I installed my poly mounts it looked pretty scabby and was kinda falling apart.

Now I'm 90% sure that the instructions from RR said that the shield was optional, so I left it out.

Well today I pulled the drivetrain back out and lo and behold the drivers side mount was melted. :eek:

Just thought I would share with the syty world so others wouldn't make the same error.


TurboTony
 

badnewz

Member
Who is selling that stuff, and what are the part #'s. If I could get a link I would buy a set of the adapters and mounts.

Thanks,

Mike B
St.Clair Shores, MI
 

UNIsackV6

Member
On 2002-02-10 19:22, NWSTP Eastside wrote:
Head over to http://www.nwstp.com

look under products section...

part #'s, contact, install page, everything you shall need.

Nice work guys I know what a pain in the ass this job can be...but you make it about as easy as it is gonna get, nice quality too, and Jeff thanks for all your help in the past...
 
Top