Nissan 240sx swap - please help

Edub

New member
Hi guys. I'm completely new to this forum and to GM tuning so I'd like to begin by saying hello.

Myself and a few other guys are looking into using one of these ECUs for our custom Nissan KA24 turbo motors. I understand this is one of the most versatile and tunable ECUs out there and think it would be sweet. I'm guessing that the 2.0L turbo Sunbird memcal is the closest match to our 2.4L I4.

The question I have now is how to go about the tuning process. I see from some of the posted links that VE is a good place to start and I have some VE values for WOT - the rest are yet to be seen.

So, once I graft the ECU to my harness and make any necessary mods, where do I begin? Also, if I just give the car to a tuning shop and say "do it" how much should I expect to pay?
 

SBNova

New member
Re: Nissan 240sx swap - please help

VE tables are where you adjust the fueling. Higher numbers entered equal richer fuel mixtures. You would nee to make sure that the chip is set for the same or similar size injectors as there is no quick input for injector sizing in the $58 mask for our ECM's. For more info, try thirdgen.org in the DIY-Prom section. There are more people there swapping GM ECM's into non-GM vehicles than you will probably find here. Craig Moates sell all the hardware you will need to tune your ECM, at Moates.net. Good luck.
 

turbodig

Active member
Re: Nissan 240sx swap - please help

Edub said:
Hi guys. I'm completely new to this forum and to GM tuning so I'd like to begin by saying hello.

Myself and a few other guys are looking into using one of these ECUs for our custom Nissan KA24 turbo motors. I understand this is one of the most versatile and tunable ECUs out there and think it would be sweet. I'm guessing that the 2.0L turbo Sunbird memcal is the closest match to our 2.4L I4.

The question I have now is how to go about the tuning process. I see from some of the posted links that VE is a good place to start and I have some VE values for WOT - the rest are yet to be seen.

So, once I graft the ECU to my harness and make any necessary mods, where do I begin? Also, if I just give the car to a tuning shop and say "do it" how much should I expect to pay?


The graft-in process is going to be the biggest part of the deal... tuning will seem like chicken-feed in comparison.

I think you might find a 2.5L N/A memcal that could be used.. that would likely be closer.
Also, assuming yours is a DOHC motor, the Quad-4 cars might be a better choice. There were a number of Late-80s quad-4 cars (Achievas, Calais) that might be a closer match.

I think you'd be lucky to find anybody locally that would work on such a thing. Most of them will tell you to buy an aftermarket ECU.

The Thirdgen.org web site has a whole book on basic tuning stuff. Searching around this forum will net you some basic how-tos on stuff you'll need to get going.

Good luck, sounds like a fun swap.

Later,

Dig
 

Edub

New member
Re: Nissan 240sx swap - please help

I checked out thirdgen, there is a lot of good info. I am familiar with programming EPROMs but I am still a bit confused on memcal selection and why this is important. As for the bin, I was told to use one from a turbo Sunbird because of the way it deals with the turbo. In one ECU swap article the guy mentioned keeping his stock memcal but using the Sunbird bin on his V8. So, you can mix and match bins and memcals? Would I be better off finding something with a closer displacement - would it be set up for boost? My car is actually an SOHC. I guess I'm just not understanding what this whole memcal business is all about. My current ECU just has an EPROM.

As for injectors, is there not an equation that can be modified accordingly?

I know you guys hate all these nooby questions - sorry.
 

2kwik4u

Resident slow guy
Re: Nissan 240sx swap - please help

There are some injector constants in the bin you can modify to change that. Thats not a huge issue.

KA24 have a distributor? If so I don't see it being a terribly hard swap. Injector, and timing control is all you really need. You'll need to verify the Nissan sensors output matches the GM ECM's expected input (or convert to all GM sensors). In the end, aside from alot of wiring to go through, I don't think it'll be to bad.

The Memcal is what the EEPROM "ride" in. Think of the Memcal as a carrier for the Chip....Or an adapter from the chip to the ECM. I'm not knowledgable enough to know exactly what the memcal does, but I know it's gotta be there. I "think" it houses the EST circuitry (est = electronic spark control). SOmeone more knowledgable can help more here than I can.
 

WannabaTY

New member
Re: Nissan 240sx swap - please help

If you can find a 180sx ecu you will be fine. There is a company called JGY that can probably help you with that. He use to buy our front mount IC kits from me years ago for the se-R 200sx with sr20-det swaps.
Don
 

turbodig

Active member
Re: Nissan 240sx swap - please help

Edub said:
I checked out thirdgen, there is a lot of good info. I am familiar with programming EPROMs but I am still a bit confused on memcal selection and why this is important. As for the bin, I was told to use one from a turbo Sunbird because of the way it deals with the turbo. In one ECU swap article the guy mentioned keeping his stock memcal but using the Sunbird bin on his V8. So, you can mix and match bins and memcals? Would I be better off finding something with a closer displacement - would it be set up for boost? My car is actually an SOHC. I guess I'm just not understanding what this whole memcal business is all about. My current ECU just has an EPROM.

As for injectors, is there not an equation that can be modified accordingly?

I know you guys hate all these nooby questions - sorry.

The MEMCAL itself is hardware. It sorta defines the base physical characteristics of the motor- how many cyls it has, how big the cyls are, how the motor "sounds" to a knock sensor. There is also a rudimentary approximation of injector size, for "limp home" mode.
The limp home fueling generally gets ignored, we run 84# injectors on a MEMCAL set for 30s.

The software part of the deal is what's burned into the EPROM that also happens to be on the MEMCAL.

There's some confusion out there regarding MEMCALs, since GM used to use 2 separate pieces, a PROM and a CALPAK (which sometimes gets incorrectly referred to as a MEMCAL).

Even more confusion exists, because GM used both types simultaneously. There's really No hard year cutoff where they quit using the one and started the other. After '94, pretty much everything went to flash PCMs due to federal OBDII requirements.

The long and the short of it is that there are many possibilites out there for MEMCALs, and you can generally program any software image onto them.

An example-

The $58 Mask ID (Program ID) code that runs in the SyTy ran in a 1222749 ECM, with a MEMCAL specific to a 4.3L, 6cyl motor. You can run the same code with a MEMCAL for a 4-cyl (as it did in the Sunbird app), or a V8 MEMCAL from an F-body car that ran in a different ECM model. (a 1222730)

The '730, '749, and '727 (an underhood-hardened version of the '730) are all very close cousins from a hardware standpoint. Most code that ran in any of the above ECMs will run in any of the others.

Ludis' web page is pretty much the Mecca of the GM ECM info world. He's got a pretty complete breakdown of what was used where, and with what motor:

http://www.cruzers.com/~ludis/p4xref.html


If your car is a SOHC motor, a late Sunbird MEMCAL would be a good choice. It doesn't really have anything to do with the turbo, but a SOHC motor sounds different to a knock sensor than a DOHC, or a pushrod motor. GM tuned these specifically to the acoustic signature of the motor they were to be used on, so you're not gonna ever get an exact match, but you should be able to find something that's close enough.


Later,
 
Top