Swap camshafts without removing A/C condensor?

Tooky

Serious about performance
I spent the last hour searching and couldn't find the answer. I'm stripping the heads and front brackets etc. all off the motor to do Vortec heads and a cam swap. However I just had my A/C recharged about a year ago and would hate to lose it. I plan to flip the compressor over by the stock battery location.

But what about the cam? If I take out the radiator, will there be enough room to R&R the cam without hitting the A/C condensor? I don't have the cam yet but judging by the length of the block it looks really close.
 

Bill Z

Donating Member
Re: Swap camshafts without removing A/C condensor?

I did an engine replacement without loosing my A/C by doing like you said (flopping the compressor over on top of the battery).

Once you remove the radiator, you should have more than enough room to change out the cam shaft. Just to make sure, take a tape measure and check it out. The short cam in these V6s aren’t very long. If it won’t quite make it, try undoing the motor mounts and raising the engine just enough to clear the radiator mount.

Let us know.

Good luck.
 

Tooky

Serious about performance
Re: Swap camshafts without removing A/C condensor?

Followup question.... if I pull the timing cover to swap cams, replace the timing cover gasket, am I going to get a proper seal? The oil pan doesn't need to be pulled, does it? I'm a first timer :)
 

dgoodhue

BuSTeD 4.3
Re: Swap camshafts without removing A/C condensor?

I am pretty sure you will be fine, but I will look when I get home.

Edit I would remove the oil pan.
 
Last edited:

Loeryder

New member
Re: Swap camshafts without removing A/C condensor?

When I swapped my L35s I held my 412 cam up to the front of the block and decided we would wait until we pull the whole motor to do the cam.

I had the radiator out but it still looked too close to the condenser for my liking.
And I was running out of time to leave for Nats so I cut my mod list down to what we could do in a week.
 

turrrbo6

Member
Re: Swap camshafts without removing A/C condensor?

I pulled mine also for the vortecs and cam swap. Nice time to clean everything!!!
 

turbodig

Active member
Re: Swap camshafts without removing A/C condensor?

TookyCat said:
I spent the last hour searching and couldn't find the answer. I'm stripping the heads and front brackets etc. all off the motor to do Vortec heads and a cam swap. However I just had my A/C recharged about a year ago and would hate to lose it. I plan to flip the compressor over by the stock battery location.

But what about the cam? If I take out the radiator, will there be enough room to R&R the cam without hitting the A/C condensor? I don't have the cam yet but judging by the length of the block it looks really close.

Loosen the condensor so it moves a bit (without removing the hoses). You should be able to make it.

Can always loosen the core support bolts to get a little wiggle room, too.
 

protosy

New member
Re: Swap camshafts without removing A/C condensor?

TookyCat said:
Followup question.... if I pull the timing cover to swap cams, replace the timing cover gasket, am I going to get a proper seal? The oil pan doesn't need to be pulled, does it? I'm a first timer :)

the front of the oil pan can be an issue. if you are lucky you wont rip the pan gasket and can get your timing chain cover back on without it getting goobered up. if it does get messed up, i'd think u'll end up pulling the oil pan.

i've only done it a few times, not a ton of experience. i am sure others will chime in with their input.
 

leroy

Donating Member
Re: Swap camshafts without removing A/C condensor?

I've done this. You don't have to remove the condenser. You need to drop the oil pan for the best result. Some people trim the timing cover a bit and then press it in without dropping the pan.

Jim
 

E-Rue

New member
Re: Swap camshafts without removing A/C condensor?

been there done that........ a couple of times already.

oil pan needs to come down when you remove the timing cover, or when you reassemble it, it will slowly seep oil from the front cover for the rest of its life. iv done one both ways...... oil pan is a damn nightmare to drop with the front diff all in the way, if you dont have a lift, but its better than leaking oil from the timing cover. if you ahve a lift..... its a no brainer .....take the pan down.

AC compressor easily flips out of the way and lays to the side but i believe you have to move the condensor to get the cam to slid all the way out. so you would have it made, except the cam is too long to come all the way out with the condensor in place.....(unless im mistaken, mine didnt ahve AC when i did it) i dont know how your gonna do that without taking loose the hoses, but i wish you the best of luck.

take lots of pics for the rest of these monkies that want to do the same install.

e
 

Don W.

Stab it and steer it
Re: Swap camshafts without removing A/C condensor?

When I removed my pan I took the front dif out. I wonder if just removing the 4 support bolts and lowering it would do it? Also, IMO removing the starter and lower bell housing helps a bunch. Not sure you can do it otherwise. :2cents:
 

Tooky

Serious about performance
Re: Swap camshafts without removing A/C condensor?

Alright guys I'm at the moment of truth.. I got the lifters out, timing chain off, radiator removed etc. All that's left is to pull the cam. But I have my new cam and I eyeballed the length of it by setting it near the block and touching the condensor, and the distributor gear and rear journal look like they'd still be in the block when the cam is hitting the condensor. Due to the delicate nature of the cam bearings, I don't want to pull the stock cam yet, only to find out that it doesn't clear.

Can anyone say definitively what it takes to pull the cam with the A/C condensor still installed? I've removed the rubber upper mounts for the condensor which allows it to flex back a little bit but it sure looks like I could use an extra 1-2" yet. I have never pulled a cam but I'm expecting it needs to be absolutely straight right until the very last journal comes out. If I could cock it sideways at the last journal I'd be home free but I am not expecting that benefit.
 

Black Knight

I Glow Therefore I am
Re: Swap camshafts without removing A/C condensor?

Can't tell you for sure 100%, but when I got rid of the A/C in my truck the back of the condensor was very beaten up, like someone tried what your attempting at one time and found out it's very, very close.
 

leroy

Donating Member
Re: Swap camshafts without removing A/C condensor?

Nice documentation Josh! I don't remember doing that, but I may have had the transmission crossmember out to give a better angle?

Jim
 
Top