Thanks to all Got what i needed

kessler

New member
Ok heres whats going on, I just finished up the motor build and reinstalling in into the truck and i crank it but it wont start, I have good fuel PSI and i have spark but it seems like the fuel injectors aren't kicking. Would a bad Ignition Modual do this or am i just looking in the wrong places. I even went so much as redoing all of the grounds thinking that it might be that.

Any suggestions would help.



Thanks
 
Last edited:

Loeryder

New member
Re: Please Help

Re: Please Help

A noid light will tell you if you are getting signal at the injector.

Someone just posted about borrowing one of these from AutoZone.

Have you timed the motor yet?
Start by checking your firing order, TDC, and try starting it with the tan wire disconnected.
 

4C FED

Absolutum Dominium
Re: Please Help

Re: Please Help

DId you double check that TDC for #1 cylinder jives with #1 on the distributor?
 

kessler

New member
Re: Please Help

Re: Please Help

well even if i was 180 off the thing would still pop like its trying to start. I have power at the Injector clip. and there brand new 75lbrs from RPM. And the plugs are dry.
 

MRKING

New Parts for Old Trucks
Re: Please Help

Re: Please Help

Is your ecm modified for the larger injectors ? Possibly the chip isnt seated properly in the carrier ?
 

kessler

New member
Re: Please Help

Re: Please Help

Yes its the Turbo time V3 for the 75lbrs. I have checked it 3 times now. I have an extra Mudual for the Distributer and my question is this now would it tell the ecu when to fire the injectors by it reading the Distributer?
 

MRKING

New Parts for Old Trucks
Re: Please Help

Re: Please Help

kessler said:
Yes its the Turbo time V3 for the 75lbrs. I have checked it 3 times now. I have an extra Mudual for the Distributer and my question is this now would it tell the ecu when to fire the injectors by it reading the Distributer?


To run injectors larger than 50-65 lbs , like your 75's , the stock ecm has to be modified by installing larger injector drivers . Thats a seperate item from the chip itself . If it hasnt been done , the symptoms you describe will exist .

You didnt say yes or no when I asked so I wanted to reiterate my question . It is a must do with the 75's , your ecm wont fire them without it .
 

E-Rue

New member
Re: Please Help

Re: Please Help

MRKING said:
To run injectors larger than 50-65 lbs , like your 75's , the stock ecm has to be modified by installing larger injector drivers . Thats a seperate item from the chip itself . If it hasnt been done , the symptoms you describe will exist .

You didnt say yes or no when I asked so I wanted to reiterate my question . It is a must do with the 75's , your ecm wont fire them without it .

he is exactly right, your ECU must be modded with low impedance drivers in order to fire the injectors...... im gonna assume you know what your doing and that this has been done and the ECU has been verified to work.............


if you dont come up with anything after diagnosing it, hit it with a quick shot of starter fluid and see if it comes to life. way back on the first version of this chip we had a couple of trucks that wouldnt fire up on their own cold. im just curious if your having a similar issue. 75lb version 3 should not have this problem, but every truck is different, and it could be a million and one things not making your truck start. keep in mind if you dont have the relay mod to go with the modded ECU your not gonna get proper voltage to the ECU and your fuel curve will be largely skewed from what we see here on the trucks we built and developed this program for. heres a picture to help you with the relay install if you havnt already done it. as you can see in the picture, the pink and black wire going to the ECU was cut. the part coming form the dash goes to trigger the relay (mine was mounted in the engine bay) and the power wire coming from the relay is atached to the ECU end of it.

aaa.jpg



e
 

kessler

New member
Re: Please Help

Re: Please Help

ok well i didnt mod the Injector driver due to i didn't know that i had to. So how can i do this and who can do it. Then does anyone have a Wiring diagram on how to get the ECU more voltage for that Mod?

More importantly where can i get the parts to do this mod, I need it done ASAP i leave for NC in 10 days and i need the truck up and running.
 
Last edited:

turbodig

Active member
Re: Please Help

Re: Please Help

MRKING said:
To run injectors larger than 50-65 lbs , like your 75's , the stock ecm has to be modified by installing larger injector drivers . Thats a seperate item from the chip itself . If it hasnt been done , the symptoms you describe will exist .

You didnt say yes or no when I asked so I wanted to reiterate my question . It is a must do with the 75's , your ecm wont fire them without it .

Also, there's a wiring harness mod, if you want to run them true peak-n-hold.
Otherwise, you're just saturating some low ohm injectors.

DIg
 
Top