KR with loads of alky

Re: KR with loads of alky

turbodig said:
the HEET bottles are convenient to carry around behind the seat if you need a quick fillup.

Thats why we have a bed to carry our 5 gallon jugs of meth.
 

TYTILIDIE

METH HEAD
Re: KR with loads of alky

I just have a motor cycle type gas jug and when I need to take some meth with me I full up a used up washer fluid bottle. But I go through about a gallon every three days.
 
Re: KR with loads of alky

There are a few guys on there that use HEET (yellow bottle). I think I got each bottle of HEET for under one dollar at Walmart. I spent $20 and that fills up my alky control holding tank twice. I heard windsheild washer fluid is not the greatest to use. Especially the ones that are dyed.
 

Flyin Ryan

hated cuz he drives fords
Re: KR with loads of alky

I said it before and i'll say it again... or just qoute myself :)


Flyin Ryan said:
running a mix of alky and water is a waste in my opinion. By that I mean your not getting the most out of what you have.. sure the water provides a anti detonant effect of a cooler combustion chamber but I feel it's offset by the greatly reduced energy water would provide compared to methanol. Water does provide energy as it goes from liquid to gas when the molecules are expanding but methanol also has a pretty good latent heat of evaporization and does so at a much lower temp. So it cools the intake like water does but also while raising the octane of the fuel in the combustion chamber. It also provides more power than gasoline in direct contrast to the reduced power that water provides you... so basically if you want the most of out of your alky injection kit don't run mix run striaght meth. Sure mixes are cheap and easy to find NOT why not go to Home Depot and in the paint section grab a jug of denatured alcohol?

Also if your going to use windshield washer fluid, do not use the Green, Yellow or Orange washer fluids. They contain glycol and depending on the consentration of it.. it can causes some problems... also stay away from anything that says "de-icer" as well.
 

syclone3

Member
Re: KR with loads of alky

I use VP M1 in five gallon cans. Tune cars every week on my dyno with Alky. Some like to mix it 50/50 with water. I like mine 100% meth. Hot weather or location thereof with the tank can make it boil so the water helps with that.
Most cars will pick up a full point of fuel that needs to be worked with. I like to stick with 11.5-12.0 on my cars using pump gas and alku.
And all require more timing to make power. Unless there is something wrong with the combination or engine. Depending, 2-5 degrees in some cases can be added.
Just giving general alky tuning guidelines. Getting read to put some on my beater Syclone. Have a Snow kit and a newer SMC. Not sure which one I will use. Do have a 1.75 gallon tank that I will mount behind the seat. Sure alleviates problems with heat.
This truck has been a small mods and bolt on project. Need to dyno it again to see where its at. All stock and a plugged converter was 237 and 357 tq. Mustang dyno. Looking for 300-320 with the current stock turbo setup on alky. Its always had 100 in it since I got it.
 
Re: KR with loads of alky

OK the new plugs helped and things are making a little more sense. I can get runs with T3 20psi setting on my ultimate with no KR at all. But then I do not change a thing and I see timing being pulled again on an identical run. Do I need to move my injector to the front of my intercooler to get more consistent runs?
DSCF1180.jpg
 

NecroWolf

lost marbles member
Re: KR with loads of alky

i would think spraying through the intercooler wouldn't help it mix right and i could see it forming drops from the mist, i think the common place to spray is right in front of the throttle body. seems a lot of people drill and tap the outlet neck on the intercooler
 

Flyin Ryan

hated cuz he drives fords
Re: KR with loads of alky

NecroWolf said:
i would think spraying through the intercooler wouldn't help it mix right and i could see it forming drops from the mist, i think the common place to spray is right in front of the throttle body. seems a lot of people drill and tap the outlet neck on the intercooler


I agree
 

Tooky

Serious about performance
Re: KR with loads of alky

You never responded to all the earlier suggestions pointing out that you need to lean out the gasoline at the injectors when running alky. You also need a wideband. ???
 
Re: KR with loads of alky

Oh sorry. I guess my main goal was to get no KR before I turned the injectors down.
I have datamaster, an ETG (its not even close to as good as a wideband), I did not lean out the injectors. I have just been tuning off the knock count datamaster gives me. I do notice exhaust temps are lower now that Im using alky. I was just curious as to why I get good runs, and change nothing and all of a sudden it turns bad?
 

Tooky

Serious about performance
Re: KR with loads of alky

It's a lot more challenging tuning additional FUEL (alky) when you don't know your Air FUEL Ratio...
 

NecroWolf

lost marbles member
Re: KR with loads of alky

you could be flooding out yuor plugs too. an egt is a useful tool, but so is a wideband and a knock sensor. each has its uses. egts and afr can show spark knock, a knock sensor can help i dentify an off afr, etc....
 

Flyin Ryan

hated cuz he drives fords
Re: KR with loads of alky

maybe you have false knock?? you might want to stop spraying alky and try getting your tune right first then you can spray alky and back the fuel off a bit etc .. just an idea I didn't re read this whole thread so if that makes no sense sorry
 
Top