How to lift cab off frame?

ed hess

race or get outta the way
looking for some ideas and or pics on lifting the cab only from one frame to another frame. the bed is a no brainer.

I would like to do this with nothing more my engine hoist cherry picker.

So whats the best way to do this.

1 straps thru the door windows?
will this bend the roof or doors?

2 straps under the body running front to back
not sure if body mounts would keep the straps from wanting to move inboard.

Also not sure if back wall would want to bend in at seam where floor meets the back wall.

3 another solution would be to move the chassis next door on dollies (navingationg driveway aprons might prove dificult) and use the arms on an above ground lift, using wood to create space to clear cladding mounts.

So beyond my thoughts, HOW DID YOU DO THIS?

moderators:

Please allow me some leeway posting this into the general section. I just hope to get more reads in the hope of getting a good answer.
afterwards you can store this one in the vault or tech archives. And yes i did search this prior to posting

thank you
ed
 

Syclone#1992

SyTy.net Moderator
Re: How to lift cab off frame?

No problem Ed! Good luck, I have never done this, but I think someone in Arizona did this, if I remember right it was a blue syclone.
 

syclone3

Member
Re: How to lift cab off frame?

You can use a cherry picker. I would leave the doors open and blanket wrap the roof edges. We used a recovery strap that was 4 inches wide and 20 ft long. Was my dads idea and the cab didn't get damaged at all.
 

ed hess

race or get outta the way
Re: How to lift cab off frame?

i really need to find a cherry picker setup pic, showing the straps mounting and or looping location.

I do find the aspect of using the fender mounting locations as front lift points interesting.

I plan to cut the cage from the frame and move the cage with the cab, which makes this even more interesting.

ed
 

turbodig

Active member
Re: How to lift cab off frame?

'nother idea...

Old winch attached to rafters. Do the long straps (If you had some really long,wide ratchet tie-downs, you can use those, but as was mentioned, wrap them heavily with moving blankets.
 

Luke

Fish sticks SUCK !!!
Re: How to lift cab off frame?

didnt MRKING swap bodys from frame to frame??
 

JSM

Active member
Re: How to lift cab off frame?

I did this with my ty. What I did was jacked the car up as high as I could, then put jackstands on the outside edges of the body. I then placed the jack on the frame, unbolted frame and lowered the frame from under it. Then slide frame out, new frame back in.

Option 2 would be to jack the body off the frame, then use some cross beams to fully jack body off allowing the jack stands to be further out making removal of frame a bit easier.
 

bezerk

New member
Re: How to lift cab off frame?

forklifts are da shizzle.
ryan.jpg
 

super-gt

New member
Re: How to lift cab off frame?

^^Lol...that pic makes me cringe!

When I had to move my cab off my frame, we removed the doors and seats but left everything else on. Between 4 of us we were able to lift it and get it off but let me tell you that thing is a heavy mother! Especially when you are holding up the corner where the AC is.....Good luck to ya!
 

turboj91

New member
Re: How to lift cab off frame?

Option 2 would be to jack the body off the frame, then use some cross beams to fully jack body off allowing the jack stands to be further out making removal of frame a bit easier.[/QUOTE]


If you are doing the work yourself I agree with the above. I did this for my Chevelle. Unbolted the body (cowl back) from the frame and jacked the body up enough to roll in a 2x3 steel beam with legs/wheels. One under the cowl (at the torque box mounts) and one in the back (trunk mounts). Made small pillars with bolt holes to mount the body onto the beam (just square tube) and then tied the legs front to back to prevent collapsing. The body was now higher than the chassis and I rolled out the chassis and rolled it back in when I was done with it. All by myself in a one car garage with just a floor jack and wood blocks.
 

LIL QIK

HELL YEA I GOT BOOST!
Re: How to lift cab off frame?

I just used my engine hoist on my full size halfton when I did it. Was planning on doing the same thing with the Syclone. Figured it would be even easier. It was extremely easy doing it that way on the halfton. Granted....it's a fairly heavy duty hoist.
 

ViciousV6

400HP/550FTLB
Re: How to lift cab off frame?

Ed,

Perfect would be a 2 post lift would work the best, if not then Harbor freight has the chain hoists which could be hung from the ceiling (steel beam, wood beam etc) use 2 hoist and one for each side.

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=2954

1300lbs should cover the body, if not get 2 smaller ones they have 880lb and 1100lb units.

Being electric too its easier to operate by ur self or 2 people.

Hope its helps!

Ralph
 

jpalmer

New member
Re: How to lift cab off frame?

well i have replaced my cab on my s-10 2x,two people, two 2x4s and room to move. they are surprisingly light. even with the doors on and glass installed but gutted otherwise.
 

ty-rob

New member
Re: How to lift cab off frame?

If all you can use is a cherry picker and put straps thru the window opening wouldn't that put the cherry picket at its upper limits before you start lifting. I've never tryed it so I don't know if it would work but what if you remove the seat and with two pieces of chain or two straps make an x between the outter seat mounts on the floor and put the cherry picker thru the window or remove 1 door. I dont know if the fire wall being the heavist part how the ballance would be. Just a thought, hope it helps
 

ed hess

race or get outta the way
Re: How to lift cab off frame?

thanks to all who input their ideas. plenty of good ideas and examples.

so i have to wonder if the seat belt mounts on the floor in the rear corners have enough meat around them then....

if so hows does this sound.

hook to seat belt mounts in rear corners of floor

hook to top fender mounts on top door hinge.

now since my syclone has a sunroof in it... rear straps thru the roof and front straps up and i think this just might center the weight on a cherry picker and allow the boom to be fully extended to 1000 lb setting on it. same as i use to pull the motor.

sure sounds easy to me.

now i gotta find some clamps to keep the cage from falling out the bottom when i lift.


btw, 2nd attempt at a good frame delivery is supposed to happen tomorrow... :)

thanks to all

and thanks to the moderators for their help
ed
 

mattw

Active member
Re: How to lift cab off frame?

So is this new frame getting blasted and painted/coated??


-Matt
 

JSM

Active member
Re: How to lift cab off frame?

If the seat belts don't hold do you really think they were strong enough to save you?
 

ed hess

race or get outta the way
Re: How to lift cab off frame?

TwinTurboV8Ty said:
If the seat belts don't hold do you really think they were strong enough to save you?

beats me because the weight of the driver multilplied by whatever g force is distributed accross all three seat belt mounting points.

then again if the straps are all adjusted perfectly and the cab drops it will land on its initial resting place. .... hopefuly lol :)

this is going to be the same kinda feeling you had right before you turned the key on that 1st motor you ever did. :)

and the new frame, just going and only going to do whatever it needs.

but paint only, no powdercoating or anything crazy. ie. same epoxy paint i used on my cage and the original frame.

ed
 
Top