Trying to solve boost and idle issues

Im trying to figure out why my boost hits 15psi real fast and then slowly creeps to 20 psi. I changed the boost solenoid and also shortened my waste gate rod. None of this helped. My truck has also been idling really bad lately and even dies sometimes. I have all new plugs, rotor, cap, and wires, TPS sensor all the obvious stuff. I decided I needed to start doing some digging to figure this out.

I pulled the throttle body off, and then checked the IAC. The IAC looked really good. But there is a lot of black oil in the inside of the throttle body.

DSCF1308.jpg


I also removed my EGR block off plate. It looks really corroded. Maybe boost is escaping from there?

DSCF1310.jpg


I looked down then intake and there is a ton of black oil. Looks like some bad blow by. What do you guys thing I should do? It’s real black oil and not any new looking oil. I did have a chemical flush last year trying to flush out that noisy lifter.

DSCF1309.jpg


I’m also going to replace my intake gasket just incase. It’s just coming off in small pieces and making a mess. Is there a trick to getting old gaskets off? I don’t want to use sand paper and get metallic dust down into the engine.

DSCF1303.jpg


I have paper towel around the valve covers because I also just put in a 160 thermostat and got clooant pooled up.
 
Last edited:
Re: Trying to solve boost and idle issues

bezerk said:
datamaster?

Ha ha yeah I knew someone would ask for that. Its not really telling me much. I also have not logged in awhile because Im waiting for my license key from TTS.

I have a file from a couple of weeks ago that has me idleing. How do I post it up?
 

bezerk

New member
Re: Trying to solve boost and idle issues

taker a look at your o2 reading. if you are to lean under wot. your exhaust temp will go up. and hard to control boost, also might be your actuator might be leaking.
TTS is a bitch to deal with if it comes to codes. somebody will have a patch around here
 
Re: Trying to solve boost and idle issues

Oh and I do have a new O2 sensor also. Im actually have fuel pressure way to high right now. My fuel pressure gauge broke and now its stuck at 50 psi base until I get a new gauge to see what Im adjusting to.

I also thought maybe I was running to rich at idle and killing it that way. I never had that problem before though.
 
Re: Trying to solve boost and idle issues

In my file all that I see that stands out is STerm Percent and LTerm Counts. Im not really sure what those are. Their fields turn red.
 

denny

Active member
Re: Trying to solve boost and idle issues

Shortened your wastegate rod will increase boost, check the vaccum lines from the turbo to solenoid to the wastegate for leaks cracks.
 

WyoSyclone

Active member
Re: Trying to solve boost and idle issues

I think Denny has you on the right track... vacuum leak... soak the intake manifold gasket with Goo-Gone (walmart)... put it on (heavily) in the morning and when you get back that evening the gasket should come off easily.
 
Last edited:
Re: Trying to solve boost and idle issues

WyoSyclone said:
soak the intake manifold gasket with Goo-Gone (walmart)... put it on (heavily) in the morning and when you get back that evening the gasket should come off easily.

Sweet! good idea!
 
Re: Trying to solve boost and idle issues

denny said:
Shortened your wastegate rod will increase boost, check the vaccum lines from the turbo to solenoid to the wastegate for leaks cracks.

I changed the boost solenoid and also shortened my waste gate rod. None of this helped.
 

Don W.

Stab it and steer it
Re: Trying to solve boost and idle issues

How is actual oil consumption? You might be sucking oil past a bad EGR valve. (The one that goes to the TB.) This would also cause funny idle. Is everything ahead of the TB clean? Meaning the IC side of the TB, outlet of turbo. Just wonderin'.
 

bezerk

New member
Re: Trying to solve boost and idle issues

FYI. 870's is a bit to lean. it might not have affect on your boost, but lean means higher EGT's and will spool the turbo harder. might get bad boost control cause of that.
 

turbodig

Active member
Re: Trying to solve boost and idle issues

They all (intakes) look like that after a few years of sucking PCV fumes in.

Unless you've got a lot of breathing out of the oil fill, I wouldn't worry about it.
Mine looked ugly at 8800 miles.
 
Re: Trying to solve boost and idle issues

Don W. said:
How is actual oil consumption? You might be sucking oil past a bad EGR valve. (The one that goes to the TB.) This would also cause funny idle. Is everything ahead of the TB clean? Meaning the IC side of the TB, outlet of turbo. Just wonderin'.

Its does not use much oil and I have never seen any oil past the intercooler inlet.
 
Re: Trying to solve boost and idle issues

bezerk said:
FYI. 870's is a bit to lean. it might not have affect on your boost, but lean means higher EGT's and will spool the turbo harder. might get bad boost control cause of that.

Thats strange because Im using alky and Im getting no knock at 20 psi. Maybe I need to turn it up more. I like to be a little lean and have no knock because thats when you make your best power. But maybe you are right. I will add more alky.
 
Re: Trying to solve boost and idle issues

turbodig said:
They all (intakes) look like that after a few years of sucking PCV fumes in.

Unless you've got a lot of breathing out of the oil fill, I wouldn't worry about it.
Mine looked ugly at 8800 miles.

Ok that makes me feel better :tup:
 
Top