009 calibrations

kwick6

Donating Member
I will be getting the 009 injectors in the mail next week. I want to install them, but am thinking I might need a chip to get the right amount of fuel. Could I put them in and just lower the fuel pressure? If anyone can help me out I would really appreciate it. I don't have the burner at my house, but a friend does.

Thanks,
Scott
 

kwick6

Donating Member
Why do I keep making the wrong decisions??? It was a dumb idea to throw that te44 on. I am getting very poor throttle response. It actually stalled today. It has me pretty nervous considering all the work that I have put into it.

I think that if I can get my new 009s in and get the fuel dialed in then it may be ok.
So where do I go from here? I regret not trading for the frankenstein turbo. I would have been able to leave the injectors alone, no need for a 9/11 torque converter, and I would have had excellent spooling. But NO.
It is really a struggle to try and get it to run properly since I put this turbo on. I am frustrated to the point that driving the truck is no longer fun. Its a real PITA, but I know I'm not the only one to have ever gone through this.

Its funny, some have the ability to get speedpro when they need it, or anything else for that matter, and there are some that struggle to pay for a set of spark plugs.

Later,
Scott
 

Buster

New member
Your going in the wrong direction, adding 009's to fix your problem is a bad idea, but since you've already ordered them E-mail me and I'll set you up with a chip. BTW: The stock injectors will work with that te44, I told you that last time you asked, but obviously you didn't listen.
 

kwick6

Donating Member
On 2001-10-28 21:50, Turbo Sy wrote:
Your going in the wrong direction, adding 009's to fix your problem is a bad idea, but since you've already ordered them E-mail me and I'll set you up with a chip. BTW: The stock injectors will work with that te44, I told you that last time you asked, but obviously you didn't listen.

Mark,
I don't have your email address.
Thank you for your help.

Scott
kwiksix@msn.com
 

kwick6

Donating Member
On 2001-10-28 21:57, 1FSTSIX wrote:
Scott, i'll be happy to trade my stock parts for yours......j/k
I acually dig the fact that i get a great idle...
If you like i can bring my tech-2 over and i can re-burn your idle to 775 or 800 or?
It worked great for me...

Who is this?
I would appreciate any help that comes my way. As far as trading goes, I don't think you would really want to do that...trust me.

Scott
 

kwick6

Donating Member
Oh yeah I forgot you got that plate Thom.
How is the ty running? Do you have my new email address... kwiksix@msn.com?
Get ahold of me sometime so we can do some wrenching. Have you changed plugs, cap, rotor yet? I would like to try those NGK plugs out, have heard they make the trucks idle nice.

Mark, I got your email. I am waiting to hear back from Jim...to see if he can burn that bin to a chip for me. If he can't I'll let you know tommarow or the next day. I haven't decided what to use for boost control. I am leaning towards the ANS though. The reason I bought the injectors was because I have a feeling that the ones that are in are shot. I didn't want new stock injectors because that would be a waste of money. I am going to try and get this running good and see if I can find any problems with the scantool. I can't really understand why the acceleration is so slow, or why it stalls more often now. It usually stalls after I start it when its cold. I will have to find out how to post a datamaster file....no clue how to do that.
I don't really have any idea what to set the fuel press. to. I had it at ~50psi base and it seemed to run really sluggish..so I raised it to 60psi base and it had better throttle response but lagged on acceleration..(too rich) So I dropped to ~55psi base and now its sluggish agian. I am not making much progress like this and the truck drives poorly. I need to get it so the idle, off-idle and cruise all react well to a certain fuel press. But that is where I just don't seem to know what to look at. Maybe 02's ...AFR's, ???
It could be in the chip??? I am using a Todd A. 16lb street program. If a stock chip would be easier to work from maybe I'll through the 2 bar map back in and get it running good on the stock chip.

Thanks,
Scott

<font size=-1>[ This Message was edited by: kwick6 on 2001-10-29 18:56 ]</font>
 

Buster

New member
There's nothing wrong with Todd's chip, but I'd put the stock chip back in and set your fuel pressure at 43 psi. I've got a set of stock injectors for sale for $100, might be a good idea.
 

kwick6

Donating Member
On 2001-10-29 20:11, Turbo Sy wrote:
There's nothing wrong with Todd's chip, but I'd put the stock chip back in and set your fuel pressure at 43 psi. I've got a set of stock injectors for sale for $100, might be a good idea.

If I put the stock chip back in, I'll need to buy a 2 bar map sensor. One thing that I heard about the ultimate chip, which may pertain to this chip I have also...is that the injectors are running static. They are controlling the amount of fuel by adjusting the fuel pressure. I could be wrong. Lets say for instance, just example here, the stock injector will flow "X" amount of fuel at 30psi so instead of calling them stock injectors we will call them X lbs. injectors.
So to get more than the X out of them they run them at static (wide open) and control the amount of fuel by the pressure. Likewise,
The 42.5lb injectors will flow 42.5 @45psi consistantly. So with the fuel press set to 45 it will flow as they are made to, not static.
I have heard that the injectors get a little squirrely at static and cannot be consistant.

No flames please, just let me know if I have somewhat of the right idea. It could have been that when I raised my fuel press to 60psi base it liked it but as I accelerated, the flow became very erradic.

Just let me know what you think. And don't laugh... :razz:

Scott
 

Buster

New member
More fuel pressure will deliver more fuel per pulse, so adding fuel pressure will deliver more fuel across the entire rpm range, regardless of what injector.

You need bigger injectors when you are running the stock injectors static, which you are not. If you were you'd be very happy with your trucks performance, this is why I don't advise people to get bigger injectors when their truck isn't running up to par.

Chuck B just ran an 11.44 @ 119 mph with stock injectors, I'd guess he's running static even with C16, but that 119 in the 1/4.
 

Buster

New member
Now let me explain the reason I think your going in the wrong direction with the 009's. Since we started out with the calibration from the stock injectors it would make sense to upgrade to an injector that flow linear to the stockers.

The 009's are not linear to the stock injectors, so you end with with a messy calibration, which can cause problems. So now when you have a problem you don't know if it's your truck or the injectors or your calibration.

Here's a quick clip from Joe at PTE.

First of all I do not wish to argue semantics, terminology, or definitions of linearity. If someone was to flow a Stock injector, 36# Bluetop,868, 42.5# 009,MSD50 & 55 at say 3ms,6ms,12ms, etc to Static opening, what would the results be?

The 36#BT at idle & midrange pulse widths(45 PSI) flowed 15-17% more than a Stock Injector, & 20-22% richer at static opening. The 868# so called 36# at idle& midrange pulse widths flowed 24-25% richer than a stock injector, & 16-17% richer at static opening.

The 42.5# 009 at idle & midrange pulse widths
flowed 57-58% richer than Stock Injector, and 42-44% richer at static opening.

The 50# Delphi (MSD) at idle & midrange flowed 60-65 % richer than Stock Injector, and 65-70% richer at static opening.

For additional information, the stock injectors we used flowed 29.5 to 30# at 45 psi static flow.

The 36# Blue Tops flowed 36-37# 45psi Static.

The 868 flowed 34.5 to 35.1# 45psi Static.

The 42.5#009 flowed 42.6 to 43.8 Static.

The 50# Delphi (MSD) flowed 49-51# Static.

So if some one were to ask what injectors exhibit a nonlinear flow characteristic compared to a stock injector or a flow plotted curve I would have to say 868's,& 009's. BTW the Red stripe injectors 38/40# exhibited the same (non-linear) flow characteristics as the 009's, although I didn't use them as an example.

If I was asked what upgrade injectors are the most linear and easy for most to program, it would be the 36#BT,& 50# Delphi/MSD. Of course the 38/40# 42.5# etc. are easy to program now that flow characteristics have been established. The examples I gave above were comparisons with certain type injectors compared to a typical stock GN injector. This type of comp. is helpful when putting together a programming scheme.

We have also flowed all types of injectors using our state of the art flow bench (developed for the ZR-1 project) and have plotted their flow characteristics. Believe it or not there are LINEAR injectors. I found it ironic that I took a 50 Delphi injector that happen to flow 50.3#/hr at 45psi at 6000rpm static, and then flowed it at 70% duty cycle at 4000rpm and it flowed 35.1#/hr. Heck I would say that's pretty darn linear?? In closing to address the original subject, yes tip in problems can be in the program. But I have found more often then not IAC, TPS settings, or MAF problems have been the culprit.
If I remember correctly if you set your fuel pressure at 3-bar (43.5) and put the vacuum. back on the regulator it would drop about 4 to 5 PSI...to 38-39 PSI. Of course this depends on the manifold vacuum at idle, which of course can be affected by some things, like a hotter cam. Also higher idle at colder temps would affect the vacuum applied to the regulator. I would suggest that fuel pressure should always be adjusted with the vacuum. line off, and also important that the engine be fully warmed up. Remember injectors are rated full delivery at a certain pressure, most are rated at 43to 43.5 PSI (3-bar) i.e. 42.5#/hr at 43 PSI. So if you set your fuel pressure at 35-36# vacuum ON, then with vacuum OFF it could only be 40 PSI. If this was the case you would not get full delivery of the injector at WOT, even if the injector was programmed to go static.
 

kwick6

Donating Member
Mark,

I know what you mean about not changing injectors just because you truck might not be running up to par. The injector linearity was explained well. It makes me think that the 50's would be a better choice because of that. The reason I thought of changing them was because of the bigger turbo. I tried for a long time to get a compressor map, which I was told by a list member...Dr Lew..that he could do a calculation for sizing injectors to that turbo. I don't plan on changing injectors right away, and it seems that the stock injectors may have been plenty, so I am not going to make things worse by throwing in the 009s. I want to be completely sure that I have run out of injector and will want to know why. What kind of things on datamaster could I look at to make sure I am running the right amount of fuel? My pyrometer isn't all that accurate to me yet as it seems to be a range and keeps me from running too lean. So if it isn't necessary at this point to go to a larger injector...than when would it be? I am just talking in terms of turbo size. I thought if your turbo was forcing almost twice the amount of air than the fuel should be raised substantially.

Thanks,
Scott
 

Buster

New member
You can size your injectors by your trucks performance. If your trucks running 110 or better in the 1/4 I'd say it's time to step up to the 50's, yes the stockers can go a bit faster, but your pushing your luck. Get a hold of a G-tech and find out what kind of power your making, my mph on the G-tech was around 116 which was 110 at the track.

There's really no function in Datamaster that says your trucks running rich or lean other than at idle/cruise, but you can look for tell tales, one tell is if you start seeing knock retard at high boost, but before you can trust this reading you have to verify that it isn't picking up false knock. Run a tank of 110 and if your getting knock with 14-15 psi your probably getting false knock but if your getting 0 knock most likely it's work. Once your knock sensor is working properly, then you can start using it to tune, next get your truck running up to par.

What's running up to par? Manifold temps under 160 at the END of a full 1/4 mile blast, engine temps between 160-180, 0 knock retard, maybe a few degrees at the TCC lock up which happens at 66-69 mph, Good boost control (no spikes), timing set at 0, 13V-14V battery voltage, new plugs, wires, and cap.
 

smeagol

Active member
The linearity issue is why I chose the 50s, this has been apparent for years. The 009s are a pain to deal with. The calibration I had running for my Ty with the 50s was better than how it ran with stock injectors. Yes the 50s are expensive compared to 009s, but time is precious, and I've already spent loads of time on the 50s, let alone what would be needed on the 009s.

Static issues - stock chip goes static early, Ultimate goes static a *bit* later. Early meaning like 15psi/4000rpm versus 18psi & 4000rpm. These are blanket statements, don't quote me.

Brian G
 

kwick6

Donating Member
Brian,

If you would be willing to sell me a 50lb chip that would be great. I wouldn't mind paying a bit more for the 50lb inj. since it would be worth it. Are they MSD's?

I only thought about using the 009s because they weren't quite as big as the 50's, but now I can see why they would be better because of their linearity. The other alternative would be to buy a new set of stock injectors. I would rather not do that because of the fact that you said the 50's could be dialed in to perform better than the stock.

Hey I know all you need is another person bugging you for a chip, so if you say sure I promise never to post another injector topic....... :smile:

Could someone please explain tip in.?? I think Mark mentioned it and was wondering what kind of issues that presented.

Thanks,
Scott
 

smeagol

Active member
I'm sure we can get you a chip somehow. Do you have an Ultimate or just stock setup now?

Tip in - off idle is one of those areas that is hard to calibrate where it feels very good in all conditions. AE fueling comes into play as well as the regular VE fueling. 009s have a difficult to tune bottom end, so tip in is as much a hassle or more. With the programs we have going now, it's pretty well dialed in.

Brian G
 

kwick6

Donating Member
On 2001-10-30 15:05, Red Canyonero wrote:
I'm sure we can get you a chip somehow. Do you have an Ultimate or just stock setup now?

Tip in - off idle is one of those areas that is hard to calibrate where it feels very good in all conditions. AE fueling comes into play as well as the regular VE fueling. 009s have a difficult to tune bottom end, so tip in is as much a hassle or more. With the programs we have going now, it's pretty well dialed in.

Brian G

I am at a stock setup. Is the 50lb similar to the ultimate, with the control box?

Thanks,
Scott
 

kwick6

Donating Member
Brian,

In the stock set up, where all the injectors are fired every 360* of crank rotation, are you getting 2 pulses per injection event.

So, if I understand this then... You have changed this to Quasi-asynchronous fueling where instead of getting the 2 pulses you might get a single pulse. That would be more desirable getting the one pulse of 1ms from a 50lb injector than 2 pulses of .5ms.

Another question I have is about overboost.
If overboost occurs what is done for safety?
Fuel dumped in?, and/or timing retarded?

Thanks,
Scott
 
Top