10s Again finally!!

autoaddictions

Active member
Well went to the track tonight!! Frist pass off the trailer 11.07@125mph. Not bad. Harry anderson was there helping Ed Hess and he came over and took a look at my logs leaned out my early boost maps added some timing -- Bam, Next pass 10.93@126mph!!! Mad props to Harry!!! So finally a repeat 10 sec pass. My air intake temps are super high in the 200s so it looks like The RPM intercooler is out of efficiency and Ill need a bigger one or some meth. Im pretty sure with lower intake temps 10.70or 60s can be run. I had a good 60 ft a 1.61 due to the quick 8 track prep. That help as well.
Ralph and Don were also there tonight Ralph i believe ran his best pass to date i think 11.3s and Don managed to drive his home without blowing anything up so thats a positive step for him as well. Nice work don. In all it was a good night there were some other SyTys there and it looked like a NASTE meet!!

http://www.youtube.com/watch?v=JTice0XnLis
 
Last edited:

WyoSyclone

Active member
Re: 10s Again finally!!

Good job, Frank! I knew that was a 10-second Ty first time I saw you pre-stage at Nats... how fast can it go... that's the question :D
...Rob
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
Re: 10s Again finally!!

yeah good time tonight it was packed with friends, 6 from south nj meets "wrx's, sti's" 5 from central nj and pa "all wrx's" frank, ralph, ryan "boostedpimp", dennis "crazykease", and ed hess, then another friend in a 71 240 with a gn motor in it. sorry if i missed some one there was so many people there tonight. good times frank, ralph and myself all got new bests. and i did not blow anything up which is a blessing in it self, even though i have a boost problem i just can not figure out.

don
 

Windedv6

Ty n 10s
Re: 10s Again finally!!

How much boost were you running? I am running McCoy's ATA and can keep it 130*-140*. There should not be that much difference between McCoy's and RPM's. I am pulling in 100% outside air vs under hood hot air. That dropped me about 25*. Are you running a EGT gauge?

John
 

autoaddictions

Active member
Re: 10s Again finally!!

Windedv6 said:
How much boost were you running? I am running McCoy's ATA and can keep it 130*-140*. There should not be that much difference between McCoy's and RPM's. I am pulling in 100% outside air vs under hood hot air. That dropped me about 25*. Are you running a EGT gauge?

John
27 PSI 21* of timing. No egt gauge. No scoop on the intercooler and no intake tube to cold air( open Turbo ) I dont have much room for a intake but i need to figure out somthing on that.
 

alwayswantedone

Donating Member
Re: 10s Again finally!!

Wow nice that you backed up your other 10.9 Frank and Ralph with a new best very nice. Most shocking is that Don didn't break anything haha. Sounds like it was a good night I should have come out to NJ a day earlier damn.
 

Captain Morgan

Moderated User
Re: 10s Again finally!!

Nice job frank. :tup: Ill have to get out to the track one of these evenings, I havent seen Ed run in over a year, would be nice to get my ass out there and breath in some fresh rubbing for a change.
 

Windedv6

Ty n 10s
Re: 10s Again finally!!

Here is what I did. I can always put my blower fan back on if I really needed it some day. This setup pulls cold air in from the high presure cowl area.

Engine72turbo3.jpg


I used the same holes as the blower motor and blocked off the passage to the interior with high dense foam (easily reversible). Also the filter is larger than most ppl can fit in anywhere. This setup uses a 4" cobra elbow and a 4" 90* elbow. Short 4"dia x 2" long sleves connect them together. I got the elbows from "Turbo Time". The tube was made by my local fab guy and covered with a custom heat blanket from DEI products. It the same material that they have to cover starters, etc. I wraps around and holds with velcro.

Another thing I do at the track is pop out my head light and roll the elbow around and down. It aligns perfectly with the back of the light. I enlarged the back of the light pocket to 4" also. You don't have ot take out the light pocket or mess with anything but the two little screws on the light trim and pop out the light at the track. Works great. In my link below you can see the light out on the run. I painted the pocket light grey so it isn't that noticable.

On your run. Where did you end up on AFR and with what gas. I use 110 octane and around 11.9 - 12.2 afr with 26* timing. I would not recommend that to everyone, but my intake setup as a better distribution than a ported stocker, which helps to have all the cylinders running consistant AFRs. The problem I had with a ported stocker intake is the my O2 sensor reading was averaging cylinders running rich and others running lean. The telling sign was reading the plugs as they were not consistant. I started poping some head gaskets. I then switched to the Bowtie/Pontiac single plane intake. Having the plugs reading consistant I was able to increase both the timing and the AFRs. I run the same turbo as you at around 27 - 29# boost.

John
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
Re: 10s Again finally!!

i gained over 30 rwhp on a dyno with only removing a 4" cobra elbow "no pipes or filter elbow only" to running a open turbo. i also had a 4" pipe coming out of the cobra elbow down in front of the wheel for street use.
 

George Blake

DONATING MEMBER
Re: 10s Again finally!!

Raist103 said:
i gained over 30 rwhp on a dyno with only removing a 4" cobra elbow "no pipes or filter elbow only" to running a open turbo. i also had a 4" pipe coming out of the cobra elbow down in front of the wheel for street use.

Guys, watch those cobra elbows. It may have been a fluke but when Tasos was setting his truck up, he found out he was sucking his flat (30+ psi) and had to go another route.
 

sytyguy

Moderated User
Re: 10s Again finally!!

I put a night cam in my engine bay once and ran at 28 psi. My cobra elbow was collapsing a great deal. Changed elbow styles and put a hose clamp in the middle (to keep form).....MUCH better now.

Hood
 

Flyin Ryan

hated cuz he drives fords
Re: 10s Again finally!!

wow totally missed this thread but yea great night of racing.. and great meeting you Frank your ty is awesome in all aspects! meth injection will be your friend
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
Re: 10s Again finally!!

yeah i heard the same thing about cobra elbows so when i was on the dyno 23psi mine only moved in about 1/4-1/2 in. i probably have a vid of it somewhere
 

George Blake

DONATING MEMBER
Re: 10s Again finally!!

Raist103 said:
yeah i heard the same thing about cobra elbows so when i was on the dyno 23psi mine only moved in about 1/4-1/2 in. i probably have a vid of it somewhere

Everybody's isn't gonna move the same. Tasos had pontiac heads, a fabricated intake and a turbo the size of a trash can lid mated to a 5" exhaust. It moved some serious air. If someone is running moderate boost and the engine doesn't have as high a demand, it may not be an issue for that person.
 

Windedv6

Ty n 10s
Re: 10s Again finally!!

A couple of years age my cobra elbow was sucking in to the point where it was choking off the air causing the engine to die off. I spent days thinking it was fuel or electrical related. I finally discovered a hole in the elbow where the turbo shaft end was starting to punch through. I reinforced elbow with a thin metal plate and had no problems since.

John
 
Top