1st Datamaster runs

Zac

New member
Made my first datamaster run's this weekend. I think that I am having a fuel problem. I have a new fuel pump & AFPR just not installed yet.

This weekend, the truck was running extremely bad. On the second run, the truck was surging very badly. On the forth run, I could barley keep it started.

I was hopeing that someone could possible confirm or deny the possible fuel problem.


My Mods:
Conrad Cap & Rotor
NGK UR5's
Taylor Spiro Pro's
3/4 heater hose IC lines
Boost gauge
MSD 6a

If any one could check them out, I will e-mail you a zip file.

Thanks alot in advance,
Zac
zacshead@hotmail.com
 

Falco

Donating Member
Zac,

Quite a busy week for me, so just took a look at it so far.

First of all. Have you read the FAQ on left? You should follow it and search for some basic stuff.

How old is your ignition stuff? Have you checked your timing? To TDC too? etc..

The files are really noisy. Lotsa data errors. You could try to adjust your ALDL timing in DM, but I'd bet it comes from a somehow bad ignition (light show under hood/MSD6) or some bad grounds. Pls check your grounds too.

It'd be nice to see some WOT runs, but you shouldn't do it with a severly sick truck.

Will look at the file a bit later and try to check fueling...

Peace,
 

Zac

New member
Falco--

First, thanks for taking some time to check out my files.

Yes I have checked out the FAQ. The truck was running decently for a little while.

I have been reading on tweeking the DM communication setting's. That was the first thing that I was going to try to do first. Another list member suggested that I try grounding the ECM. I probably will try this, I just have to figure out to do this.

It'd be nice to see some WOT runs, but you shouldn't do it with a severly sick truck.

Yes, I really don't feel comfortable going WOT Right know. If you floor the gas, the Boost builds but the truck is very, very sluggish. If you stay into the gas, you can quickly hear a popping sound. This can't be good.

How old is your ignition stuff? Have you checked your timing? To TDC too? etc.

Wires, coil, Module, C&R =3k miles
Plugs= 200miles or so.

Timing is about 1.5-->2 degress retarted.
Haven't checked TDC yet. I have the Piston stop, but haven't had time to use it yet.
This is on my list of To do's.

I have been thinking that I should remove the MSD6a. It is currenltly mounted in the Glove box.

Pls check your grounds too
I will do this to. A couple other's have told me to check this.

If I can answer any other ?'s let me know.

thanks,
ZAC
 
B

Blake

Guest
Your MSD is mounted in the glovebox? It is just inches from your ecm. You just answered your noise problem. It is supposed to be mounted as close to the battery as possible and not upside down. The instructions say it won't drain water properly if you don't. I've seen a couple installs where it is mounted very stealthly on the fender, out of the engine compartment. Kinda on the other side of the stock coolant overflow.
Blake

<font size=-1>[ This Message was edited by: Blake on 2002-01-17 17:26 ]</font>
 

Syclone#892

Member
Msd sells a noise filter to install in the power wires from the box and it works very well. I had the same problem with data errors and I put the filter in and the problem was solved.
 

Falco

Donating Member
Zac,

Firts thing is to remove that MSD6 from you glove box. Remove it completely or put it as Blake said. Hopefully it will solve the problem.

About the ECm grounding. I've connected my ECM cover and one of my ECM ground lines to the frame where the motor is grounded (driver's side on the firewall).

Rgds,
 
Top