9 sec syclone build!

Z SKI

Donating Member
Re: 9 sec syclone build!

You have to figure in about 30% more fuel for e85. I plan on running 120# injectors for the e85. That should be good for up to 750 HP For reference I maxed out 74# injectors on race gas in my typhoon running mid 10s and stepped up to 84#. 84# would be good for around 550 600 with e85. Not good enough for my combo on corn.. So I'm going to 120#.
Fuel pump is the bigger issue. You'll need plenty of pump for e85.

Thanks Frank... How do the 120#'s idle and drive on the street?? I got one of those new Holley double pump units, we'll see how it does..

See ya,
 

autoaddictions

Active member
Re: 9 sec syclone build!

Thanks Frank... How do the 120#'s idle and drive on the street?? I got one of those new Holley double pump units, we'll see how it does..

See ya,

I guess i will find out! I have run 160s before never tried 120s. I was able to tune out a good idle. I dont think it will be a problem. Then again im using a Big stuff system so it might be harder with a stock setup code 59. Not sure what your using for fuel management.
 
Last edited:

Z SKI

Donating Member
Re: 9 sec syclone build!

I guess i will find out! I have run 160s before never tried 120s. I was able to tune out a good idle. I dont think it will be a problem. Then again im using a Big stuff system so it might be harder with a stock setup code 59. Not sure what your using for fuel management.

Cool man!! Let me know how it goes with the 120#ers. I'm running the Holley Dominator with a distributor-less ignition setup with sequential fuel injection... It will either run really good, not run, or blow up... One of the three... Thanks again for your help and can't wait to see you Sy and your Ty finished!! :rock:
 
Last edited:

autoaddictions

Active member
Re: 9 sec syclone build!

More done today its starting to come together. Got the fuel system plumbed with all Teflon lines Mounted regulator installed fuel rails and Intake. Distributor dropped in, new vacuum lines, Headers, Turbo and turbo and support bracket built and installed!! Still lots to do!!

Big stuff install ,relocate battery to bed, install gauges, Wire up fuel pump,MSD,Fans.










 

TYTILIDIE

METH HEAD
Re: 9 sec syclone build!

Very nice!

If you don't mind me asking, how are you running those lines to the heater core? Is the core after market or did you sweat some fittings on thrre?
 

autoaddictions

Active member
Re: 9 sec syclone build!

Very nice!

If you don't mind me asking, how are you running those lines to the heater core? Is the core after market or did you sweat some fittings on thrre?

Nothing special!! I cut them shorter then slid the -12 Hose over with some hose clamp AN style ends. The block side is -12 AN. I put some RTV on the copper ends before sliding the hose over It helps hold them on without leaking.
 

0966Sy

Code what?
Looking good Frank, I like the black wrinkle coat. Did the same with my Sy on certain components. Are you doing a plug n play BS3? Tick, tick....12 more days. Looking forward to your results
 

autoaddictions

Active member
Re: 9 sec syclone build!

Looking good Frank, I like the black wrinkle coat. Did the same with my Sy on certain components. Are you doing a plug n play BS3? Tick, tick....12 more days. Looking forward to your results

I am cheating and using the plug and play i pulled from the Typhoon. I do have a standalone harness but im going to use it in the Typhoon for the Bowtie upgrade. Im going to run a racepack dash so ill go the rip out old harness deal. Nice write up BTY!!

12 days no problem!! Big challenge though Totally stock to fully built Stock Block In 23 days. Now that im seeing results its motivating me. Im hoping my pic uploads will do the same for some other members here.
 

fivetodrive

CRISPY
Re: 9 sec syclone build!

The waste gate location is interesting. Can't wait to see how you do this!

What size down pipe are you going to run?
 

autoaddictions

Active member
Re: 9 sec syclone build!

The waste gate location is interesting. Can't wait to see how you do this!

What size down pipe are you going to run?

Down pipe is 3" v band. Im going to run a electric dump this time. I want it as quiet as i can for driving around in.

Waste gate recirculates back into the down pipe for a quiet experience as well.

I almost have the engine bay done. I will update post with new pics tomorrow should have front end back on, and intercooler piping and down pipe in place.
 

autoaddictions

Active member
Re: 9 sec syclone build!

Lots more completed on the Sy today. Drive shaft showed up today very nice piece from Dynotech looked sweet right out of the box!!
Installed that and tightened up all the vbands topped off the fluids!!
Installed the plugs and wires fit the exhaust to the down pipe.
We put some fuel in the tank for the first time, tank was good but had to deal with a few small fuel leaks. Fixed the loose AN fittings then re tested fuel system all the way to 90psi.
Plugged in the big suff system loaded up a start up tune.

Im very pleased to get this running in just 3 weeks!! It could of taken months..

Keith Watson was here with me for the whole project! He turned most the wrenches while i mostly Tinted windows for customers all day, and steered the project.
Big thanks to Keith!!

Dynotech 4L80e Aluminum Shaft


New light weight custom straps installed on the rear yoke!! We will have these available for a group purchase soon.
 

Sportmachines

Active member
Re: 9 sec syclone build!

Well done Frank and Keith! That things going to be a monster. Love the speed and quality of the build. Kuddos!
 

fivetodrive

CRISPY
Re: 9 sec syclone build!

Do you have a gallery with more pictures of your engine? I really wanted to look at your headers and the way that they connect to the wastegate and then back to the downpipe. Your build is unique due to the vband exhaust housing.

Thanks!

Aaron
 

1BADV6

Donating Member
Re: 9 sec syclone build!

Very nice Frank, but then again I have come to expect nothing but from you :)
 
Top