95 vortech 4.3 turbo?

ForceFedFbody

New member
i know this isnt exactly syty, but i figured you guys would know better than anyone else..
i was wondering how a later model (1995) vortech 4.3 V6 would hold up witha single turbo?
i have a chance to pick up a complete blazer that was involved in a roll over accident for verryyy cheap.
what do u think it could handle as far as boost with stock bottom end and compression ratio? possible power out put and ANY reccommendations for turbo (t03/t04??) intercooler and fuel upgrades???

*id like to keep it sorta on a budget if i do decide to do it, like put about 1500-2000 into the motor*

any help would be extremely helpful...Thanks - Keith
 
Most people's honest opinion will be to save your money.

It get expensive to turbo a NA 4.3 reliably.

But, you could feasabley run 10 psi safely if you threw a alcohol injection kit on. As for the intercooler, the only restriction is what you can fab up to put in front of the grill. You would also need to go electric fan.
 

odium

1BADGMC
I'm with smaug, especially if you are on a budget. If you weren't on a budget, you could do it for 4-5000, and it would be a clone of a syclone/typhoon engine w/ upgraded pistons, rods, pretty much all the internals.

Divergent is also right, but you would HAVE to have an intercooler and HAVE to have the alcohol to run the 10 psi. If you have no alky, you could probably only run 5 psi safely, with a perfect tune, with no internal changes to the motor. Shortly after you get the motor done, you will probably then shatter the transmission.

Save your money and do a 5.7 swap. You could easily do that for ~1500 in just about any car/truck you are planning on working with.
 

stuartlittle

New member
I'll help you some what. First off you're looking at a Central port injection motor with probibly one of the Worst designed intakes ever. So #1 you're looking at a new intake. SyTy Intakes I've seen run well over $500. Then you're looking into injectors *6 then a New computer and Harness possibly. Then you're looking at Rods, Pistons, Cam, Rockers, Exhaust, Plumbing, Map sensor 2 or 3 bar, and a lot of tuning time. Now remove all the items needed to change out from the motor you're looking at and you have a Block, Crank, BALANCE SHAFT, Heads and Valves. It's not being said that you can't do it, Heck I'm going to do it. But when you through the word Budget into the mix you're looking at the imposible route.

Now I'll tell you a little of what I'm faced with in my 95 4.3 CPI engine that's identicle to the one you are looking at. #1 I'm looking at All the parts stated above plus I'll be fabbing up my own intake from scratch going off of pics that I've seen and such. This will not be easy And will require Tig Welding. While I do have these resources this still will not be cheap. I'm looking at close to $6K in building this engine alone, but I'm looking at More HP than the stock SyTy engines. In a completely different vehicle.
 

BigBadSmoosh

Picking fights on I-65 since 2013
all you guys with these cmpi 4.3s..

if you happen to have an extra good working one around with say less than $100k miles.. let me know..

mine has 130k and has started leaving oil everywhere, I still drive it and I will until it goes boom, but it would be nice to have a backup plan.

and no, I don't feel like going out and buying something else, I want a house not a new daily driver.
 

Lynn D. Brown

New member
4.3 Turbo'ed

4.3 Turbo'ed

Hey Guys,

I knew the SyTy Int Man. was unique and hard to find - NLA from GM.. Is it the Upper that's different ? Is the Lower the same on all the 4.3's ? In which case, U could have a sheet metal Upper made. I know Mike Lee of RPM sells them, but they are $2000. +.

The block is the same except for the balance shaft after '93, wasn't it ? They say that the balance shaft makes it weaker, but I'm thinking it's probably OK as long as U don't go mega-HP. The crank is only slightly upgraded - nodular instead of grey Cast Iron - and I think U can still get it from GM Perf Parts. And it's easy to get forged pistons in the right CR.

Of course w heads, the 96+ Vortechs are supposedly a big upgrade. If I do this upgrade, I will go w a '96 + engine - I imagine there should be a few in the J-Yards.
 

stuartlittle

New member
Pretty much all internals are different. But when going with Turbos if you don't want to buy a Turbo Cam you can get away with the STOCK cam.
 

Drac0nic

New member
I've put considerable thought into a JY style 4.3L turbo. I'd go with a TBI intake and TB, that way you've got all the sensors there. Get a shop to put bungs in it for port injectors, and you're GTG. You're dealing with boost which would mean that while NICE low restriction won't hurt the motor as bad. If you can program/find someone to the 1227747 ECM from say a TBI vehicle, you may be able to get a 1 bar MAP to work with it, even though you'll lose some precision. People are probably gonna give me crap because yes it is a TBI computer, and they've only got 2 injectors stock but consider this; The injectors it uses are 2.5 ohm impedance, which means the drivers will handle 12/2.5 or 4.8A. If you use half a dozen 16 ohm injectors (stock GN injectors are 30# and 16 ohms roughly, at least mine were on the DVM) you're at 4.5A which means it won't burn the box up to use it for batch fire. The other option is to get a Sy/Ty box (you can pick em up for a 50 bucks if you watch) and make that work, it wouldn't be that much of an issue. Hell, it's probably one of the most documented GM boxes out there. A 3.8L fuel rail is spaced about right to use with a 4.3L too, at least on the cast iron Q-jet intake I've got. For a motor like that I'd be very tempted to use a pair of RHB5s from Ford Probes or a single stock GN turbo. Both of which would be more then enough turbo for that kinda ride, and should spool well. I'd probably go with the RHB5s if you could clear em, just run em off stock manifolds with adapters.. The cam with these engines more then likelyisn't the best for turbocharging, but the CPI cam is more radical then what came with the stock Sy/Tys quite frankly, which was a stock TBI camshaft. Get an intercooler, if you look around on boards a powerstroker intercooler can be had for $150-200 and it's more then you'll *ever* need for a setup like that.
 

TYTILIDIE

METH HEAD
Dude save yourself time and money and get a different vehicle. Maye be at an auction? You said this was in a roll over right? I garauntee that roof will never be as strong again unless you know someone who really knows what teh hell theyre doing. That should cost a grand atleast I would think. Then you gotta get it painted ,another 2-4 depending on what you go with. Always remember tfhat you get what you pay for. If you want to hot rod for cheap then get get someting with a better platfrom. Just my opinion.

Mike
 
Top