A/F vs Mat

Buster

New member
I posted a question in the chip section a few weeks ago and for some reason that section is gone, anyhow I've got some info that might be old news, but I thought a few of you might interested in. My original problem was my a/f ratio at wot would change on a daily basis, and really run lean on highway kickdowns, I never consider mat temp, but obviously when your cruising down the freeway and your mat temp drops you'll need more fuel for a wot blast.

When Dig and I originally tuned my truck it was pretty hot out, MAT temps would start out in the 110-120 range and end at about 160-170. Dig tuned it to be safe, I'm not sure exactly what a/f, but some where in the low 12-1's, maybe even fatter. Anyhow a few weeks later Kris and I bought a wideband and I found my a/f ratio to be dangerously high, in the mid13-1's at wot. After making a few passes I've found that my a/f ratio is closely related to my MAT temp, at 80 degrees (at most rpms and boost levels) I'm in the 13.3-1 range, then at 111 degrees (at most rpms and boost levels) I'm in the 12.7-1 range, and then at 150 I'm in the 11.9-1 range.

Anyhow I think I found the right table in promgrammer (F31M) that controls fuel based on MAT, just thought a few might be interested in this info. I haven't started using this table yet, but only problem I see is it's kind of broad, I'd be sweet if Bill could added a few tables so we could adjust fuel a little more closely based on temp. If anyones using this table I'd like to hear about it.

Mark L
 

10secTy

Sy-Ty builder and Tuner
Been there done that. I tuned Tonys to have a nice flat AF.
Then on the real cool night we would go out and I would adjust using this
table. Then on hot days same thing so now it does not matter on the temps its always 12-1.

Oh if you raise the number it removes fuel and if you lower the number it increases fuel.

Nolan
 

JSM

Active member
I have a tunercat def. file in the works, that lets you modify this table.

Here is my only issue so far with it.

I can't duplicate Promgrammers #'s exactly. I am VERY close but not exact.

For those that have used the table, I am thinking of just changing the scale factor. It won't affect chip at all, just give you different #'s to look at.

For example right now it is set to around 300 in promgrammer. 300what I am not sure.

I was thinking of changing it so 300=100... so be close to a % of fuel. Need more fuel, give it 110%... Need less 90%..

Anybody have any suggestions?
 

BillC

New member
Re: A/F vs Mat

Buster said:
Anyhow I think I found the right table in promgrammer (F31M) that controls fuel based on MAT, just thought a few might be interested in this info. I haven't started using this table yet, but only problem I see is it's kind of broad, I'd be sweet if Bill could added a few tables so we could adjust fuel a little more closely based on temp.
As much as I'd like to freely add new tables and parameters to Promgrammer, I can't. I'm limited to what already exists in the chip. Every table and parameter that is possible to adjust in the chip is already in Promgrammer (unless there are some undocumented ones I don't know about). So, if you don't see it in Promgrammer, it's simply not in the chip. :(

FWIW, there is one apparent exception to this rule: the F71_SCALE "parameter". Yes, I created and added it, but it's not really an exception. It is not a parameter in the normal sense, it is actually a chip code hack that Dig and BG developed. So, it acts as if it is a parameter, but it really changes the chip code.
 

Buster

New member
Canadian SY/TY said:
Oh if you raise the number it removes fuel and if you lower the number it increases fuel.

Nolan

Damn your sharp, I forgot to ask that question, and you already answered it.

Mark L
 

smeagol

Active member
I have the accurate representations of those columns somewhere (in Fahrenheit).. we should integrate those (unless they already are...)
 

10secTy

Sy-Ty builder and Tuner
They are accurate for celsius.
Just convert the mat temps in datamaster and tune away.

Nolan
 

10secTy

Sy-Ty builder and Tuner
Kelvin works off of absolute zero.
So zero Kelvin is like -370 something degrees celsius.
which did not make any sense. So I took it as a misprint
and used Celsius.
I will have to check the bible when I get home to see what it says.
Hehehe maybe I am just lucky :D

Oh just want to make sure we are talking about the same table its F31M.

Nolan Nykyforuk
 

smeagol

Active member
Yep, Kelvin works off absolute zero.

This is definitely a crucial table. I'll go through the code and try and find my accurate info on it.

We'll clear this up once and for all, then we'll have Bill integrate whatever changes need to be made into Promgrammer ;)
 

JSM

Active member
I can make headings anything we want on tunercat also

Had it labeled Canada, Chicago, LA, Bosnia, .... Hell once just to see if I could do it...

I am still curious as to what 300 means when you pull it up on promgrammer. I always like to know WHAT i am changing, besides just add more, take away some.

Bible is on the ftp also, if you guys need it while away from home.
 

BillC

New member
If I remember correctly, 0 Kelvin is equal to -273 Celsius. So, 300 Kelvin would be 27C, or nearly 81 degrees Fahrenheit.

There are two tables calibrated in degrees Kelvin. The rest of the temperature values are calibrated in degrees Celsius. Would people prefer that the Kelvin tables get displayed in Celsius (so all temps use the same scale), or would they prefer the tables to stay the same?
 
Top