A2A guys step in

Damian

Member
Re: A2A guys step in

Replaced the thermostat, flushed the living hell out of everything, only has water and Royal Purple water wetter. It's dark out and the temp slowly creeps up still. If it's in park, it will ever so slightly go down. To even notice it, you really have to watch the gauge carefully. I was already wanting to sell my setup so I can get the truck fixed to pass smog (no cat), but if I have to swap out the intercooler, an A2A isn't going back in.

I have a 2001 S10 Xtreme radiator, it should be sufficient? It did just fine before the A2A.
 

Damian

Member
Re: A2A guys step in

I really hate this truck. It's 68 degrees out and it still crept up on me. I'm just going to put the stock intercooler on since I never had problems before. Then I can put the stock battery stuff back in since the PC680 will only last long enough for about 10 seconds of cranking. PS, I can't stand BMW drivers even more now.
 

Damian

Member
Re: A2A guys step in

Can someone measure how thick the stock radiator core is for me please? I'm still pulling the A2A out, but this is more of a curiousity thing. I'll measure mine here in a minute and post it up for comparison.
 

Ross L

Member
Re: A2A guys step in

Are you using the factory radiator with built in trans cooler? Could your trans/stall be causing the heat issue? I don't even know what the factory stall rpm is.
 

Damian

Member
Re: A2A guys step in

I'm using a 2001 S10 Blazer Xtreme radiator with a built in trans cooler because of the turbo inlet elbow was right up against the radiator and the heater connection was in the way. I was thinking the trans might be a problem, but it never ever went above 165 degrees before the A2A install. I was just hoping I wasn't the only one with the heat issues with this setup.

I measured the radiator core and it is 1 1/8" thick. The end caps are the same thickness as stock, I just didn't check the core size before I trashed the radiator.
 

berzerker

wookie
Re: A2A guys step in

double check a couple more things before you scrap the whole set up .

1 . ) if available .. what are the temp readings from the data master ?

2 . ) what is the needle on the coolant gauges position at max temp ?

3 . ) how good is the air flow through the inter cooler and radiator cores , with
engine running in park and fan running . will it hold a large hand rag against the grille ?
 

Damian

Member
Re: A2A guys step in

The gauge reading and Datamaster show the same temps, within reason that is.

My infared temp gun crapped out, so I need to get another one.

I did put a rag on the intercooler itself and it won't even make it to the bottom because it gets stuck to the intercooler from the air flow. I'm getting more than enough air flow, at least I think I am.
 

Windedv6

Ty n 10s
Re: A2A guys step in

Not enough radiator. Get a decent dual core that most of the the s10 V8 guys run and no radiator trans cooler. Use a corbra elbow on the intake to clear the thicker end caps.

John
 

Damian

Member
Re: A2A guys step in

Instead if the radiator connection, I added a barb fitting to the back of the water pump. I did think that might be the problem and I did crimp both lines with no change. 210 isn't bad, but it will most definitely keep going up.
 

Damian

Member
Re: A2A guys step in

Ended up pulling everything out. Thanks for everyone's help. I'm going to put the stock intercooler back in, pass smog (I hate CA). I will be upgrading the radiator very soon as well. What we can get out of this is a 1" thick core is not sufficient for these trucks.
 

Syclone#2960

What ever it takes!!
Re: A2A guys step in

You need an edelbrock water pump...I live in texas and do not always need my electric fans on with a stock autozone radiator...its hands down the best mod I have ever done on my typhoon along with the hitachi starter for a daily driver. I also have a tranny oil cooler in front of the radiator blocking the air flow. Do not run straight water it can evaporate after it boils unlike antifreeze's higher boiling point.
 

Damian

Member
Re: A2A guys step in

Ill get one eventually, but I have the high output water pump from VatoZone, which they don't have anymore according to their website. After this smog check, Im going to make sure she can drive to Nebraska and back so I can register her there and say to hell with smog. Then Ill install my FAST setup and be done, for awhile.
 

T-Bone

Active member
Re: A2A guys step in

I have a brand new custom designed thick top of the line Griffin radiator that I personally drove down and picked up from the manufacturer in GA. Doubtful I will ever use it since I sold my Sy it was intended for use on (my Ty is already equipped with one). You can hit me up via PM if you are interested in it.
 
Top