advice please

11secty

New member
well need a little help here just got my ty rebuilt eagle rods ross pistons so on and so forth , my question is i bought a bigger turbo (precision 54)
do i need to do any tuning before i go out and run at 21 lbs or should i trust my ultimate chip on stage 3 setting dont worry i also have the fuel setup for the power and then some any ways here is a list of my mods for help
any replys would be nice

walbro 255 fp
front mount ic
70lb an hour injectors
msd ignition
fuel pressure reg
mbc
ultimate chip
precision 54 turbo
3 inch turbo back no cat . no emission laws up here
p/p heads
 

SeattleSy#1255

Category 5 Conservative
Don't do it....

at least get a scan tool like Datamaster and see if you are getting knock at a lower boost level first. Its not worth the risk IMO, espically when you just spent some change on a new motor.
 

kwick6

Donating Member
Don't think theres an ultimate for 70lb injectors.

I'd also recommend datamaster and a laptop. You can order datamaster from my website.

You'll need to have your ultimate reprogrammed for the injectors, or go to a custom chip, or stand alone system.
 

11secty

New member
well

well

the injectors might be a little smaller but cant i just dyno it and adjust according to af ratio thats if any one could tell me what it should be at at 21 lbs the only dyno near my house dont have any one that can tune they can just set your fuel pressure to get the right af ratio.
i heard 11.6 but maybe i'm wrong thanks for your help . and i'll have to save up for the computer just dumped a shit load of money in the motor
 

MRKING

New Parts for Old Trucks
1

1

If all they do at the dyno shop is adjust your fuel pressure , I would keep your syclone far away from that place . Tuning is changing fuel maps and adj timing tables and other complex sh*t .

You should get datamaster and see how your truck acts now , then you can go from there .
 

kwick6

Donating Member
Re: well

Re: well

11secty said:
the injectors might be a little smaller but cant i just dyno it and adjust according to af ratio thats if any one could tell me what it should be at at 21 lbs the only dyno near my house dont have any one that can tune they can just set your fuel pressure to get the right af ratio.
i heard 11.6 but maybe i'm wrong thanks for your help . and i'll have to save up for the computer just dumped a shit load of money in the motor

You need to know what size injectors were used. Your truck would run terrible if your using a stock injector calibration with larger injectors.

Tuning would be much easier if you had a stand alone system, but if your planning on using the stock ecm, then you'll have to go with an injector that has a chip thats been calibrated for it.

The $185 for datamaster is a very minimal expense, and is a necessity for all of these trucks, let alone one that has just had an engine rebuilt. I wouldn't get into boost until you have a laptop and can monitor what is going on.
 

dgoodhue

BuSTeD 4.3
Re: well

Re: well

11secty said:
and i'll have to save up for the computer just dumped a shit load of money in the motor

Datamaster doens't require that new of a laptop, anything in the mid to late 90's will do (less then $150) I wouldn't run any significant boost through the motor unless you want to be rebuilding the motor again. You need to know what injectors and verision ultimate chip you have, if I had to guess its 50#, because the larger injectors require you to modifiy the ECM by soldering different injector drivers.
 

11secty

New member
where do i buy the datamaster at and does it come with a program i would assume , then just buy a cheesey laptop something not to old
 

11secty

New member
mick do i just dowload it to my computer then save it to disk well i did that for the 87- 4.3 z code engines now do i just save it to disk then put it in the lap top while hooked up

oh and it never asked me for that license or to put it any where i just clicked on the download efi pro v 4
 

Mick

New member
You would want to download and install the EFI Live V4 "evaluation" rather then the Pro version. The software will prompt you for the license info when you first run it. Its a bit quirky with this info, as it must be entered exactly as it is on the download page. Even took me a few trys before I got it right.
The Sy/Ty vehicle stream definition is located in the "Browse vehicle definitions" page, here is a more direct link
 
Top