AEM DFI

canadian

sy in progress
http://www.aempower.com/ems.htm

anybody ever seen this in person? grabbed some information off of another list, but don't know much about it:

"I have been spending some time working with one on a
non ford application and am thoroughly impressed.
Things like wide band feedback, automapping, internal
high speed logging and a killer boost control system
are only a couple things that I have found to be what
I need in a controller. You can find out more about it
at: http://www.aempower.com/ems.htm
I don't have any prices yet, but I will probably have
them available on my website as soon as the unit is
completed. "

"Want to monitor EGT, and have the controller adjust
fuel based on EGT at say WOT and full boost? Want to
run secondary injectors? Would you like to have your
turbo boost level controlled dependent on vehicle
speed? (for example 10psi at 10mph and ramp up to
20psi at 70MPH). Want to run two wide bands (or
regular O2s) and have each bank trimmed seperately?
Want to log data at a sampling rate of 250Hz and take
a derivativetive of engine speed to see how a change
has modified your torque curve? All of this and more
is possible with this controller.

Is it overkill for some people? possibly, but it's not
something that most people will be able to grow out of
soon.

It does have a couple drawbacks - one not being able
to directly drive low impedance injectors, but you can
go pretty fast on high impedance injectors, especially
if you are using additional injectors. I'm using low
impedence in my car (as are my dad and Bob) and I am
only running about 65% DC at 9.9s and 140+ MPH. "
 

smeagol

Active member
These are big with Supras right now, and I've heard of great results with them. I am dying to use one, as I have really become a bit disappointed in the FAST system in many aspects.

The software is buggy, their 5 bar setup *sucks*, no deceleration fueling to tune, no good adjustment for large injectors; in general, it is not comparable to OEM type of fuel/spark strategies.

The AEM has a lot of I/O, and some serious potential. Downside is that, being so powerful, it's not real user-friendly, and you can really screw up a calibration; or have the potential to fix a problem in a calibration, but not know exactly how a table functions.

I'll let you know when I tune one, I should be able to get my hands on some setup soon. I downloaded the software a while ago - sick adjustments could be made to that, to the point of *too* much available.
 

TheObiJuan

Active member
it is a pretty neat software setup. i messed with it for my dsm back in july.
i remember mike lee saying AEM wanted him to test on a typhoon or something like that.
care to chime in Mike?

one easy way of changing fueling is to click on the graph, highlight the rms you want to change, and add the percent of enrichment or enleanment. (is enleanment a word greeny?)
very simple. but very easy to make your car very slow.
it would be nice to have it as an option for syty's.
you can also download a trial version to lean with and mess with.
 

smeagol

Active member
well the graphical tuning isn't anything new, DFI & FAST have had that for years. The stuff that matters is, the user-configurable stuff.

I can have a boost controller
I can use the outputs for other things (TC lockup, alky, propane, extra injectors)
I can control a computer controlled auto trans
I can log w/o a laptop
I can run DIS setup (no eDist type of external setup necessary)
I can configure it to use any type of sensor (widebands too)
I can run dual knock sensors, with feedback control, custom tuned/calibrated by me

It looks really attractive on many levels, and an awful PITA for many reasons.

Yes you can do a lot, but being able to mess with a lot means you will fiddle with shit for HOURS.

No one has set it up for a Syty yet (no base calibrations, no harness done).

Doing large injectors (aka low impedance peak n hold) isn't possible directly yet. So you'd need some sort of driver change, or external driver setup.

More on this lata...
 

smeagol

Active member
The more i look at this the more i like it. It has the flexibility I've wanted for so long - adjust this parameter based on a sensor reading or what have ya. No need to hack the code, just drop down some menus.

Also, logging lots more inputs is a BIG thing. I'll have a source for all sorts of wacky sensors & their data where I work, and I could make use of any of them (aka EGT, MAP, possibly turbo speed sensor).

Multiple 02 sensors, adjusting for different conditions (different boost control based on coolant, or air temp, or barometer)... oh man there are so many possibilities.

Logging dual knock sensors, one in each head... controlling the propane with the computer rather than an external controller like i have now

lots of fun for someone to tweak on, but part of me would rather just do simple tuning and leave it at that, rather than spending lots of time twiddling on the laptop. pricing ain't bad, $1450 is going price for plug n play setups. I wonder if I could get it cheaper than that through my sources.. hummmmm.
 

canadian

sy in progress
will it work with our trucks (ie: do they have one for gm's? didn't see anything listed on the website).
 

smeagol

Active member
I'm sure it can be done, just a matter of setting up the software & wiring correctly. Definitely not for the newbie.
 
i'd like to make the word deleanment.
seriously - smeagie - doesnt anyone realize i own a real, legit, not internet based speedshop?
i have been a dealer for aem for over 15 years - we used them for weber stuff 'fore they went all ricey.
anyway, gimme a part number u need and i can price it for you.
let's do this privately.
mike
 

smeagol

Active member
Problem is that they don't have a part number that would work easily for a Syty. Anything would require some serious know-how to get going. It'd take me some time & materials to make anything work. FAST - gimme a saturday morning, it'll be installed & running *great*.

I'll let you know what I find out. I talked to a basic EMS tech and I asked too many questions he had no answers to, so I'm waiting for a call back from a more knowledgeable tech.
 
whenever u be ready.
here's a thought
if this is gonna happen, and ems supports it, (which i've not looked into)
how about going MAF instead of speed density?
99% of the time it'll do better then 99% of the speed density systems...far more adaptable...less people bugging u for help (!) cause it'll already be able to figure out airflow increases for itself, etc etc
 

smeagol

Active member
Thinking about this more, here's what you are looking at:

Universal stand alone race setup AEM box & harness
cost- probably $1500-2000 (this isn't even available to the general public yet)

Wiring to plug it into a syty setup
cost - $100-500 (depending if done yourself or bought this way, or other custom issues)

Now you still don't have a base calibration/configuration file.

If a kind hearted, retarded person such as myself sets this up and *gives* it away, for the basic sty setup, it'd be free. This is more difficult than you'd think. How do you setup the knock sensor filtering? Or the closed loop setup? or the ignition setup? Does the knock sensor adjust timing on all cylinders? just individual? Do you setup for 2? Did you want it configured for additional custom sensors? What are their specifications?

If someone sets this up and sells it, couple of hundred bucks maybe.. I don't know.

You still won't have :

Wideband 02 sensor (have to be made or purchased, then tapped into the AEM)

Ability to use low impedance injectors (not possible *yet*). To run larger than 50# injectors, you'd have to have injector drivers upgraded or run an external driver box (more $$)

A very powerful computer, not for the faint of heart though. I am considering doing it because I'd be able to get it for a decent deal, plus I'd make it work with or without the AEM (if it takes me too long to get the AEM working properly, I'd swap the stocker back in).

The $$ is a big hurdle at this point, considering what I can do with the stocker at this point, and the time I have invested in it.
Every time I read about the AEM though, I love the features it has, and is comparable to the stuff I use at work. Crazy datalogging & calibration features. All encompassing unit, could do away with my boost controller & propane controller. Course the fact that it's winter and my mind runs isn't helping things :wink:
 
i agree - the money's nuts, and most (all?) syty guys ae too cheap/poor to spend this kinda scratch. i also agree this is far far more then nearly anyone needs.
'course, that doesn't stop bench racing and dreaming....there's no doubt this is slick as whaleshit, but i doubt sincerely it's worth teh time/money for general pop. to screw with.
i'd see essentitally no financial return from an endeavour whatsoever.
that'd not stop me from doing it for fun, IF i could justify pissing away a big chunk of $.
and, truthfully, if i was really starting from scratch with a scratch harness, etc, no baseline, etc - i'd use 1 of 3 different ford-based systems - all maf, all known and good, all worthwhile and not a fortune.
but, that aint gonna happen either, so ....
 

UNIsackV6

Member
smeagol said:
Course the fact that it's winter and my mind runs isn't helping things :wink:

Oh boy look out BG is busy thinking again :wink: Hmmm they claim to have tons of experience with the Oddfire stuff...hmmm...now if I could just find a job...
 
Top