AEM Tru boost help

JAY

Donating Member
I picked this up at NATS & was trying to get it figured out. What settings do you guys use for a mostly stock truck running ATR Pitbull chip? Isn't the stock waste gate pressure 5#? Trying to get it setup & not blow anything up in the process.
 

Big Mike

New member
Re: AEM Tru boost help

Slowly back away from your Syclone, stock is 8# without boost controller hooked up.
 

Syclone#2960

What ever it takes!!
Re: AEM Tru boost help

I installed the same gauge today and trying to figure out how to set the boost level. The instructions are not very clear.
 

eviltwin

"junkyard syclone"
Re: AEM Tru boost help

There super easy to set up if you don't read the instructions lol. Push and hold the two buttons for over 2 seconds. Should say something like program9 or so. Press the two again for another 2 seconds to get the the settings menu. To change the settings use the buttons one at a time. To go to the next setting push both buttons at the same time. It should be preset to run under the correct sensor and show psi not bar. I dont use the alarm setting but i put the guage light setting to afew pounds over my max boost setting i will run. Now just keep pushing both until you get to the spring pressure menu. They suggest that you put the spring pressure about 2psi lower than the actual spring. The point of this setting is when the wg starts to crack open. If you set this setting too high it will struggle to control the boost evenly. You can fine tune this if needed. The scramble boost setting will be the duty cycle first and time setting second. If you don't have this hooked up then don't mess with it. If you do, just remember that it uses a monetary switch. After all that you will get to the A pressure and then B pressure settings. always start low and work your way up slowly. Different wgs and springs will take duty cycle differently. Once you get that set, put the two buttons two more times and you will be set. Once your set, if you hold and press both buttons again, you can adjust the boost setting your at by simple pushing one button at a time.
 

Syclone#2960

What ever it takes!!
Re: AEM Tru boost help

There super easy to set up if you don't read the instructions lol. Push and hold the two buttons for over 2 seconds. Should say something like program9 or so. Press the two again for another 2 seconds to get the the settings menu. To change the settings use the buttons one at a time. To go to the next setting push both buttons at the same time. It should be preset to run under the correct sensor and show psi not bar. I dont use the alarm setting but i put the guage light setting to afew pounds over my max boost setting i will run. Now just keep pushing both until you get to the spring pressure menu. They suggest that you put the spring pressure about 2psi lower than the actual spring. The point of this setting is when the wg starts to crack open. If you set this setting too high it will struggle to control the boost evenly. You can fine tune this if needed. The scramble boost setting will be the duty cycle first and time setting second. If you don't have this hooked up then don't mess with it. If you do, just remember that it uses a monetary switch. After all that you will get to the A pressure and then B pressure settings. always start low and work your way up slowly. Different wgs and springs will take duty cycle differently. Once you get that set, put the two buttons two more times and you will be set. Once your set, if you hold and press both buttons again, you can adjust the boost setting your at by simple pushing one button at a time.

Thanx Garrison I found a video on another post going into detail about how to program.
 

Syclone#2960

What ever it takes!!
Re: AEM Tru boost help

Very much! Just need to figure out what to set my spring rate pressure at. I have a PTE HD Internal Wastegate. I think it's rated @18psi base boost.
 

eviltwin

"junkyard syclone"
Re: AEM Tru boost help

Thanx Garrison I found a video on another post going into detail about how to program.

Very much! Just need to figure out what to set my spring rate pressure at. I have a PTE HD Internal Wastegate. I think it's rated @18psi base boost.

No problem. The videos probably make it much easier! 18psi base is alot, I feel like base pressure should be alot lower on an internal gate.
 

Syclone#2960

What ever it takes!!
Re: AEM Tru boost help

No problem. The videos probably make it much easier! 18psi base is alot, I feel like base pressure should be alot lower on an internal gate.


I talked to PTE they said the 1011-144 actuator begins to open @ 18psi and it seems fine...at least I don't hear the turbo acting funny as described in one of the videos.
 
Last edited:
Top