Air/Fuel

BLACK92TY

It's never enough
Had a weird day at the track today. Wasn't the best of conditions for a track day but I figured I'd make some passes before I put it away for the winter up here in Minnesnowta. Times weren't dramatically different from previous best but felt week towards the end of the track. Little bit of boost fluttter, zero knock but A/F was around 14.6-14.7. For a modified truck it seems a bit lean but I'm no tuner so I'm looking for troubleshooting solutions. Wondering what you guys think about ideal A/F ratio for the combo I'm running.

Build is .030 over, 4 bolts,Eagle HBeam rods, JE pistons, Hood custom cam, L35s, 60# inj, Walbro FP, AFPR, WB02, sureflo IC pump, external WG, EGR delete, catless dynomax, Dig Tuned 17 in 1 chip so the race setting isn't the one I use when I'm weekend cruising. Usually run a more conservative setting but the boost has always been obedient (particularly after external gate conversion).

Truck ran clockwork 12.81s until now. 12.88 isn't too far off so I might seem like I'm nitpicking, but the sputtering at the end of the track is what has got me puzzled.
 
Last edited:

nallj92

Active member
Re: Air/Fuel

that is way lean, should be high 11's low 12's for afrs under WOT. Obviously this would be dependant on what the motor wanted and how Dig has the chip dialed in. May have a old wideband sensor, or fueling issues.
 

BLACK92TY

It's never enough
Re: Air/Fuel

Could a faulty MAP sensor contribute to this? Running 3Bar. Not sure how long it's been in there.
 

dgoodhue

BuSTeD 4.3
Re: Air/Fuel

I Highly doubt the map sensor. It is more likely something like the fuel pump, fuel regulator, vacuum lines.

What is the condition of your vacuum lines? Do you have a fuel pressure gauge?
 

BLACK92TY

It's never enough
Re: Air/Fuel

Vac lines are all up to par. The Walbro 255 that's in there has been in it since we bought the truck some 10+ years ago now. That was my initial thought. Fuel filter is maybe 2-3yrs old. How would you be able to tell if the regulator is bad? I don't have a fuel pressure gauge yet. Suppose that would help.

We're going to get under the hood and check the FP at idle and WOT this week. If it wasn't the vac lines, fuel pump or regulator what would most people do in this case just fatten up the fuel pressure?
 
Last edited:

dgoodhue

BuSTeD 4.3
Re: Air/Fuel

The regulator vacuum port would either have gas in it (or vacuum line smell of gas) or the fuel pressure would not either go down with vacuum/up with boost.

The fuel pump check would be to check to see if the fuel pressure increase equal with boost from the base fp. So if the base (vacuum line disconnected) fuel pressure was 45 psi, with the vacuum line connected the fp at 15psi should be 45+15=60psi.
 

Windedv6

Ty n 10s
Re: Air/Fuel

I have seen this happen. High af down track when people run multiple hot runs. The vac line comes off the regulator. Good way to blow a motor. Always put a clamp or zip ties on your vac llines...

John
 

BLACK92TY

It's never enough
Re: Air/Fuel

Thanks for all the responses guys. The more info the better. The searches have been almost an all day thing today. This helps big time.

I have seen this happen. High af down track when people run multiple hot runs. The vac line comes off the regulator. Good way to blow a motor. Always put a clamp or zip ties on your vac llines...

John

You had me very nervous, just ran down to the garage to take a peak. The vac line coming off the top of the regulator was/still is connected and zip tied to hell. Glad you pointed that out though. Thank you.
 
Last edited:

BLACK92TY

It's never enough
Re: Air/Fuel

The regulator vacuum port would either have gas in it (or vacuum line smell of gas) or the fuel pressure would not either go down with vacuum/up with boost.

The fuel pump check would be to check to see if the fuel pressure increase equal with boost from the base fp. So if the base (vacuum line disconnected) fuel pressure was 45 psi, with the vacuum line connected the fp at 15psi should be 45+15=60psi.

Very helpful. Thank you.
 

BLACK92TY

It's never enough
Re: Air/Fuel

Finally got under the hood today. Pulled the vac line off AFPR to check for gas and everything checked out. No gas or fumes. Before throwing on the Fuel Pressure tester, decided to follow a couple vac lines just to be sure, turns out I overlooked behind the intake. Found a crack in the T vacuum fitting coming off the plenum behind the intake. Kinda did a double take, saw it, pulled on it just a tad to make sure I wasn't seeing things and sure enough it just fell apart. So a new T set up and clamped as hard as I can go.

Checked base with vac off and FP was at about 44ish.
Put the vacuum back on and FP dropped to 35ish at idle.
Went out for a quick spin and FP climbed to about 60 under close to WOT. But...the A/F is still hovering in the 14.2-14.7 range.

I didn't think the vac fix would solve all my lean problems but we're glad we found it. Just kinda stumped on where to go from here. Could this be a WB02 issue? Puzzled.
 
Last edited:

Damian

Member
Re: Air/Fuel

I'm going to ask a stupid question, are those a/f ratios at idle or under boost? If under boost, how much boost?
 

Damian

Member
Re: Air/Fuel

Under boost, that a/f ratio will knock like crazy. Pull the O2 sensor out and see what it looks like. Some of them require them to be installed at a certain angle otherwise it won't read properly, or it's just bad.
 
Top