Alky tuning

smeagol

Active member
Without even reading the thread I'm sure you are referring to Derek O Banion's setup.

You should do some more reading at the www.aempower.com forums. He has more good info there.

(warning: the AEM system will make you sick; he's using it to control his alky injection system, with warnings and automated precautions if it goes dry)
 

Daron

Active member
Re: Alky tuning

That forum seems to be down, do you care to summarize Mark?
Thanks,
Daron
 

Buster

New member
Basically the question asked in the tread is what afr should be ran with methanol, 12-1, 10-1 or 8-1? According to Derek, which I'm sure is correct, you just tune to 12-1. Basically he's saying it doesn't matter if your running gas or methanol you'll still be tuning for 12-1, even know it'll take nearly 2.5 times more methanol to get the same reading on the WB sensor.

This will make tuning a breeze, in the beginning I was under the impression I'd need to figure out my exact gas to meth ratio at every boost/rpm level and shoot for a different afr. See I'll be injecting 3-4 1- mm nozzles at say 7 psi, at this boost level I'll be running almost all alky, but then as the boost goes up so will the need for extra gas, changing my alky to gas ratio at every boost level.

So the game plan now is to dump in the alky under boost and start pulling fuel until I get a nice flat afr, hopefully I'll be able to make the big boy hp (70 series with 25-30 psi) without completely reworking the fuel system.
 

Buster

New member
I'm going back to an intercooler, alky alone works, but not as good. The biggest draw back was the one-second before the alky actually hit, mats would go up like 60 degrees. Basically starting a run at 100 degrees, then add the 60, and I'd be running 160 all the way down the track, not terrible, considering I hit 200 degrees on the top end with both the stocker and KB intercooler and no alky.

I do believe alky will be the single most important part of my new combo though. Considering the possible below ambient mats, ability to burn more fuel, and the extra octane. I am planning on running race gas and alky for extremely high boost levels. I'll be reporting back either this weekend or next depending on when PTE gets my new turbo here.
 

Maxtor

New member
Mark -

Are you running straight methanol in your system? I have always used denatured alcohol from the local home improvement (96% ethanol, 4% methanol). What advantage are you seeing using meth vs. ethanol?

From the MSDS, methanol has a higher autoignition temp (683F vs. 867F), and methanol appears to be slightly more flammable with a wider explosion range. I can't gather that much more.

I was going to try methanol today, but after driving to just about all the stores I could think of I couldn't locate it. Where are you buying straight methanol?
 

Buster

New member
Methanol's better, but ethanol ain't bad. Either one work well. I like the idea that denature ain't so poisonous, just splashed myself today with straight methanol while doing some flow testing. Here's a link, if you read the whole chart you'll understand the differences.

http://www.holdfastmac.com.au/techcharts.html

As of right now I'm still using Heet, which I believe is 99% meth.
 

Buster

New member
Make sure to click on comparative rating and fuel rating, helps to understand what their talking about.
 

Maxtor

New member
Great link, Mark. Very informative. Thanks for the info.

I never even thought of using Heet when I was on my "meth quest" today, amazing how the mind can forget things you once knew...

I better watch those meth jokes; here in Indiana that kind of thing can get you locked up :eek:

Thanks again.
 

Buster

New member
Buster said:
I do believe alky will be the single most important part of my new combo though. Considering the possible below ambient mats, ability to burn more fuel, and the extra octane. I am planning on running race gas and alky for extremely high boost levels. I'll be reporting back either this weekend or next depending on when PTE gets my new turbo here.

I take all this back now, after 147 bins I've got a fricken headache. Got it tuned without alky to 20-21 psi where I'm 100 duty cycle on the 50's. Truck seems to run good at this level, actually very good. Only problem is I have to set the fuel cut at 21 psi and that's no fun.

Then I started tuning two nozzle, that was the majority of the 147 bins, maxed those out, so I went to four, tuning got a lot harder because my ignition was breaking up so bad. My ignition wasn't great with two nozzles, but was terrible with four.

According to datamaster the truck runs better without any alky, might have something to do with the ignition break up. Even got beat by a mustang on the freeway at 25 psi, the ignition was breaking up so bad I was actually losing rpms, well sort of. That's my story and I'm sticking to it.
 

Buster

New member
Ignitions all fixed up now, bought some stock in MSD. Anyhow, the alkys working much better, even works with 4 nozzles now. I'm planning on making a few track passes this weekend if the weather clears up.
 

Buster

New member
Did some real world testing, comparing methanol Vs ethanol. First pass was with ethanol, went home emptied the container, refilled it with methanol and went to the exact same spot.

Here are the results

Ethanol (4-1mm nozzles) and Pure 92 octane 0-120 mph
Mats went from 84.2 to 99 degrees.
Map was between 249 to 264 (20-23 psi)
Timing was set at 15-16 degrees, picked up 4.4 degrees of knock in 3rd
Datamaster ET:
60 feet 1.45
1/8 7.109 @ 97.7
1/4 11.27 @ 116.9 (no tcc, its broke)
Real afr was mostly in the low 11-1's

Methanol (4-1mm nozzles) and Pure 92 octane 0-120 mph
Mats went from 80.4 to 92.5 degrees
Map was between 243 to 266 (20-23 psi)
Timing was set at 15-16 degrees, picked up 3.3 degrees of knock in 3rd
Datamaster ET:
60 feet 1.46
1/8 7.10 @ 97.9
1/4 11.23 @ 118.8
Real afr was mostly in the low 12-1's
 

Maxtor

New member
Great info, Mark. I just drained the ethanol out of my tank yesterday and put in methanol after going through the information you provided. A couple of runs confirmed lower MAT's for me with methanol than I used to see with similar conditions and ethanol.

I am interested, though, that you had more knock (4.4 vs. 3.3 max) with AFR's almost a full point lower. Any ideas on why this would happen? Seems backwards. Unfortunately, I also changed injectors when I switched to methanol yesterday so I can't do any before/after comparisons with AFR.

I did notice that I can run quite a bit more methanol with the stock ignition than I could ethanol before it breaks up.

What toy from MSD did you buy to strengthen you ignition to put in more alcohol? A 6a box?
 

Buster

New member
I think the methanol maybe a bit more knock resistant, actually on the methanol run it only knocked once 3.3 degrees, with the ethanol it knocked twice, the highest being 4.4. As far as MSD, I went with the 6AL, noise filter, plug wires, 1000 degree wire protectors, and UR6ix plugs gapped at the factory .038-.040.
 

Buster

New member
Here's a little update from last week.

I decided to try out the bigger shurflo pump (1.8gpm) and upgraded all my wiring, it flows considerably more now, each pass is well over 12 oz, not sure exactly, but its sucking those little 12 oz heet bottles down like crazy.

Here's the info.

Methanol and 92 octane 0-121 mph
Mats went from 84.2 to 87.3
Map 260-270 (24-25 psi)
Timing 16-18 degrees
AFR low 11's
Knock 1.8 degrees
Duty cycle (50# injectors) 85%

Data master ET:

60 feet 1.71
1/8 7.29 @ 98.7
1/4 11.36 @ 121.0

I decided this weekend to pull the tranny and quit messing with the bad converter, while the trannys out I decided to have it freshened up a bit. I should be ready to roll by next weekend. If I can get some good solid times on datamaster I'll make a trip up to Digs track for a few times slips on 92 octane.
 
Top